Details, datasheet, quote on part number: RA13H8891MB
CategoryRF & Microwaves => Modules->800MHz Band
TitleModules->800MHz Band
CompanyMitsubishi Electronics America, Inc.
DatasheetDownload RA13H8891MB datasheet
Find where to buy


Features, Applications

DESCRIPTION The 13-watt RF MOSFET Amplifier Module for 12.5-volt mobile radios that operate in the to 915-MHz range. The battery can be connected directly to the drain of the enhancement-mode MOSFET transistors. Without the gate voltage (VGG=0V), only a small leakage current flows into the drain and the RF input signal attenuates to 60 dB. The output power and drain current increase as the gate voltage increases. With a gate voltage around 4V (minimum), output power and drain current increases substantially. The nominal output power becomes available at 4.5V (typical) and 5V (maximum). At VGG=5V, the typical gate current is 1 mA. This module is designed for non-linear FM modulation, but may also be used for linear modulation by setting the drain quiescent current with the gate voltage and controlling the output power with the input power. FEATURES Enhancement-Mode MOSFET Transistors VGG=5V, Pin=1mW Broadband Frequency Range: 880-915MHz Low-Power Control Current IGG=1mA (typ) at VGG=5V Module Size: x 6.4 mm Linear operation is possible by setting the quiescent drain current with the gate voltage and controlling the output power with the input power

RF Input (Pin) Gate Voltage (VGG), Power Control Drain Voltage (VDD), Battery RF Output (Pout) RF Ground (Case)

SYMBOL PARAMETER VDD VGG Pin Pout Tcase(OP) Tstg Drain Voltage Gate Voltage Input Power Output Power Operation Case Temperature Range Storage Temperature Range CONDITIONS f=880-915MHz, ZG=ZL=50

ELECTRICAL CHARACTERISTICS (Tcase=+25C, ZG=ZL=50, unless otherwise specified) SYMBOL PARAMETER
f Pout 2fo in IGG Frequency Range Output Power Total Efficiency 2
Input VSWR Gate Current Stability Load VSWR Tolerance
Pin=0.5-2mW, Pout<20W (VGG control), Load Pin=1mW, Pout=13W (VGG control), Load VSWR=20:1
All parameters, conditions, ratings, and limits are subject to change without notice.


Related products with the same datasheet
Some Part number from the same manufacture Mitsubishi Electronics America, Inc.

M38044MB-XXXHP : RAM Size: 640bytes Single Chip 8-bit CMOS Microcomputer

M38221E9HFS : RAM Size: 256 Bytes; Single-chip 8-bit CMOS Microcomputer

M38250MD-XXXFP : RAM Size: 192 Bytes; Single-chip 8-bit CMOS Microcomputer

M38278EBMXXXFS : Single-chip 8-bit CMOS Microcomputer

M38505ME-XXXSS : RAM Size:768 Bytes; Single-chip 8-bit Microcomputer

M38860E9A-HP : RAM Size: 192bytes Single Chip 8-bit CMOS Microcomputer

M52944FP :

M56694GP : Latched/Addressable Bi-cmos & Dmos 32-bit Serial-input Latched Driver

MF1050V-4 : Saw Filter For Digital Mobile Telephone

MGFC41V3642_04 : 7.1 - 7.7ghz BAND 12W Internally Matched GaAs FET

Same catergory

10280-3 : = ;; Size LXWXH = 1.46 X 1.75 X 0.11" ;; Packaging = Caseless ;; Frequency MHZ = 116-150 ;; Power Handling Watts = 500.

854733-1 : = Filter - Cdma BTS ;; Frequency (MHz) = 114.99 ;; Bandwidth (MHz) = 1.4 ;; Insertion Loss (dB) = 25.0 Max ;; Modes of Operation = se ;; Package (mm) = Dip - M.

AH22 : . 50-860 MHz Contains 2 matched high-linearity amplifiers in one package -69 dBc CTB -70 dBc CSO +23 dBm P1dB +41 dBm Output IP3 +70 dBm Output IP2 MTBF >100 Years +5 V Single Positive Supply The is a high dynamic range amplifier targeting cable TV markets. The combination of gain flatness, high linearity and bandwidth makes it ideal for CATV distribution,.

AM035N4-00 : 32-37 GHZ GAAS Mmic Ring Hybrid Mixer. I Low Conversion Loss, dB I Low LO Power Requirement, 9 dBm I High to RF Isolation, No DC Bias Required Alpha's ring hybrid GaAs Schottky diode mixer has a typical conversion loss an LO power level as low as 9 dBm over the band 3237 GHz. The chip uses Alpha's proven Schottky diode technology, and is based upon MBE layers for the highest uniformity.

AS169-73 : Phemt GAAS ic SPDT Switch DC 2.5 GHZ. dB +30 dBm Typical IP3 52 dBm Typical Low Insertion Loss @ 0.9 GHz) Low DC Power Consumption Ultra Miniature Low Cost SOT-6 Plastic Package PHEMT Process The an IC FET SPDT switch in a low cost SOT-6 plastic package. The AS169-73 low insertion loss and positive voltage operation with very low DC power consumption. This general purpose switch can be used.

AW002R2-12 : GAAS SPDT ic 10 W T/r Switch DC 2.5 GHZ. T/R Switch High Isolation @ 0.9 GHz) Designed for Mobile Radio Applications @ 0.9 GHz @ 25C High Intercept Point (IP3 +63 dBm,@ 0.9 GHz) The is a high power IC FET SPDT switch in a plastic SOIC-8 package. This switch has been designed for use where extremely high linearity is required. It can be controlled with positive, negative or a combination of both.

BR6535 : Frequency (MHz) = 10 - 400 ;; Gain (Typ/Min) (dB) = 32.5 / 30 ;; Noise Figure (Typ/Max) (dB) = 1.8 / 3 ;; P1dB Comp Point (Typ/Min) (dBm) = +22 / +20 ;; 3rd Order Intercept (Typ) (dBm) = +37 ;; 2nd Order Intercept (Typ) (dBm) = +48 ;; DC Power (Typ) (V/mA) = +15 / +90 ;; Package = Package = Package = 4 Pin TO-8B Package = Surface Mount Package = Connectorized.

D2054UK : Purchase Online = ;; Package = DBC4 ;; Impedance Calculator = ;; Operating Voltage (V) = 28 ;; Power Output (W) = 10 ;; Minimum Efficiency = 40 ;; Gain = 13 ;; Test Frequency (MHz) = 1000 ;; Configuration = Push-pull ;; Application Range = 1-1000MHz ;; Active Fet Configuration = 2+2 ;; BVDSS (V) = 65.

HN2C13FT : Package = TU6 ;; Application = VHF/uhf Lna.

INA-03100 : Bipolar. 5V Fixed Gain Amplifier, Flat Gain to 3 GHZ. Low Noise, Cascadable Silicon Bipolar MMIC Amplifier Technical Data Cascadable 50 Gain Block Low Noise Figure: 2.5 dB Typical at 1.5 GHz High Gain: 26.0 dB Typical at 2.8 GHz 3 dB Bandwidth: to 2.8 GHz Unconditionally Stable (k>1) Low Power Consumption require high gain and low noise or RF amplification with minimum power consumption. The INA series.

LT1527AJ : Regulating Pulse Width Modulators.

MAX2015 : 0.1GHz to 2.5GHz, 75dB Logarithmic Detector/controllerthe MAX2015 Complete Multistage Logarithmic Amplifier is Designed to Accurately Convert Radio-frequency (RF) Signal Power in The 0.1GHz to 2.5GHz Frequency Range to an Equivalent DC Voltage. The Outstanding Dynamic Range And Precision Over Temperature of This Log Amplifier Make it Particularly Useful.

RMTR13390 : MMIC. Circuit = 13-39 GHZ Tripler Mmic ;; Frequency = 13-39 GHZ ;; Conversion Loss = 5 DBM.

SGA-2286 : DC-3500 MHZ Silicon Germanium HBT Cascadable Gain Block. Sirenza Microdevices is a high performance SiGe HBT MMIC Amplifier. A Darlington configuration featuring 1 micron emitters provides high F T and excellent thermal perfomance. The heterojunction increases breakdown voltage and minimizes leakage current between junctions. Cancellation of emitter junction non-linearities results in higher suppression of intermodulation.

FSAV430 : Low Voltage Ultra Low Power High Bandwidth (800MHz) Quad SPDT Video FSAV430 is a high performance Quad SPDT (2-to-1 multiplexer/demultiplexer) video switch designed specifically for switching high definition YPbPr and computer RGB (up to UXGA) signals. The bandwidth of this device is 800MHz (Typ) which allows signals to pass with minimal edge and phase.

HMC526 : 6 - 10 GHz, 50dB LO/RF Iso, 40dB Image Rejection, +28dBm IIP3. Wide IF Bandwidth: - 3.5 GHz Image Rejection: to RF Isolation: 50 dB High Input IP3: +28 dBm Typical Applications The HMC526 is ideal for: Point-to-Point and Point-to-Multi-Point Radio VSAT Military End Use The is a compact I /Q MMIC mixer which can be used as either an Image Reject Mixer or a Single Sideband Upconverter. The chip utilizes two standard.

HMC631LP3E : GaAs HBT VECTOR MODULATOR 1.8 - 2.7 GHz The HMC631LP3 & HMC631LP3E are high dynamic range Vector Modulator RFICs which are targeted for RF predistortion and feed-forward cancellation circuits, as well as RF cancellation, beam forming and amplitude/phase correction circuits. The I & Q ports o f t h e HMC6 3 1 L P 3 ( E ) c a n b e u s e d t o c o n t i n u o u s l y vary.

HMC712 : Voltage Variable Attenuator Chip, 5 - 30 GHz The HMC712 die is an absorptive Voltage Variable Attenuator (VVA) which operates from 5 - 30 GHz and is ideal in designs where an analog DC control signal must be used to control RF signal levels over a 30 dB amplitude range. It two shunt-type attenuators which are controlled by two analog voltages, Vctrl1.

0-C     D-L     M-R     S-Z