Details, datasheet, quote on part number: MC33989DW
PartMC33989DW
CategoryPower Management => Regulators => Linear Regulators
DescriptionMC33989 System Basis Chip With High Speed CAN Transceiver
CompanyMotorola Semiconductor Products
DatasheetDownload MC33989DW datasheet
Quote
Find where to buy
 
  

 

Features, Applications

Order this document by Rev: 4.91 Date: 10th July, 2002
SYSTEM BASIS CHIP WITH HIGH SPEED CAN
System Basis Chip with High Speed CAN Transceiver

The is a monolithic integrated circuit combining many functions frequently used by automotive ECUs. It incorporates: - Two voltage regulators. - Four high voltage inputs. - 1Mbaud CAN physical interface. Vdd1: Low drop voltage regulator, current limitation, over temperature detection, monitoring and reset function Vdd1: Total current capability 200mA. V2: Tracking function of Vdd1 regulator. Control circuitry for external bipolar ballast transistor for high flexibility in choice of peripheral voltage and current supply. Four operational modes (normal, stand-by, stop and sleep mode) Low stand-by current consumption in stop and sleep modes High speed 1MBaud CAN physical interface. Four external high voltage wake-up inputs, associated with HS1 Vbat switch 150mA output current capability for HS1 Vbat switch allowing drive of external switches pull up resistors or relays Vsup failure detection Nominal DC operating voltage from to 27V, extended range down 4.5V. 40V maximum transient voltage Programmable software time out and window watchdog Safe mode with separate outputs for Watchdog time out and Reset Wake up capabilities (four wake up inputs, programmable cyclic sense, forced wake up, CAN interface, SPI and stop mode over current) Interface with MCU through SPI

WDOGB CSB MOSI MISO SCLK GND CANL CANH L2 L1
Vsup monitor Dual Voltage Regulator Vdd1 Monitor
Mode control Oscillator Interrupt Watchdog Reset

This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice.

Supply Voltage at Vsup - Continuous voltage - Transient voltage (Load dump) Logic Inputs (Rx, Tx, MOSI, MISO, CSB, SCLK, Reset, WDOGB, INTB) Output current HS1 - voltage - output current ESD voltage (HBM L3 - All other pins ESD voltage (Machine Model) All pins except CANH and CANL - DC Input voltage - DC Input current - Transient input voltage (according to ISO7637 specification) and with external component (see figure 1 below).

V Vsup Vlog V I Vesdh -4 -2 Vesdm Vwu V -0.3 Internally limited - 0.3 Internally limited Vdd1+0.3 kV

Junction Temperature Storage Temperature Ambient Temperature (for info only) Thermal resistance junction to gnd pins (note 1) note 1: gnd pins

(Vsup From to 18V and Tamb to 125C) For all pins except CANH, CANL, Tx and Rx which are described in the CAN module section

Characteristics Description Vsup pin (Device power supply) Nominal DC Voltage range Extended DC Voltage range 1 Extended DC Voltage range 2 Input Voltage during Load Dump Input Voltage during jump start Supply Current in Stand-by Mode (note 2,4) (includes at Vdd1) Supply Current in Normal Mode (note 2)

mA Reduced functionality (note 1) (note 3) Load dump situation Jump start situation Iout Vdd1 =10mA CAN recessive or sleepdisable state Iout Vdd1 =10mA CAN recessive or sleepdisable state & V2 off, Vsup<12V, oscillator running (note5) CAN in sleep-disable state & V2 off, Vsup<12V oscillator not running (5) CAN in sleep-disable state & V2 off, Vsup>12V oscillator running (5) CAN in sleep-disable state Vdd1 on, Vsup<12V oscillator running (5) CAN in sleep-disable state Vdd1 on, Vsup<12V oscillator not running (5) CAN in sleep-disable state Vdd on, Vsup>12 oscillator running (5) CAN in sleep-disable state guaranteed by design In normal & standby mode In normal & standby mode guaranteed by design

Supply Current in Stop mode (note 2,4) I out Vdd1 <2mA Supply Current in Stop mode (note 2,4) I out Vdd1 <2mA Supply Current in Stop mode (note 2,4) Iout < 2mA BATFAIL Flag internal threshold BATFAIL Flag hysteresis Battery fall early warning threshold Battery fall early warning hysteresis

Isup (stop1) Isup (stop2) Isup (stop3) VBF hyst BFew BFewh 0.1 1.5

note 1: Vdd1>4V, reset high, logic pin high level reduced, device is functional. note 2: Current measured at Vsup pin. note 3: Device is fully functional. All functions are operating (All mode available and operating, Watchdog, HS1 turn ON turn OFF, CAN cell operating, to L3 inputs operating, SPI read write operation). Over temperature may occur. note 4: With CAN cell in sleep-disable state. If CAN cell is sleep-enabled for wake up, an additional 60uA must be added to specified value. note 5: Oscillator running means "Forced Wake up" or "Cyclic Sense" or "Software Watchdog in stop mode" timer activated. Oscillator not running means that "Forced Wake up" and "cyclic Sense" and "Software Watchdog in stop mode" are not activated.

Vdd1 (external 5V output for MCU supply). Idd1 is the total regulator output current. Vdd specification with external capacitor. Stability requirement: C>47uF ESR < 1.3 ohms (tantalum capacitor) In reset, normal request, normal and standby modes. Measures with C=47uF Tantalum. Vdd1 Output Voltage V Idd1 from to 200mA Tamb 125C 5.5V< Vsup <27V Idd1 from 200mA 4.5V< Vsup <5.5V


 

Related products with the same datasheet
MC33989DWR2
Some Part number from the same manufacture Motorola Semiconductor Products
MC33989DWR2 MC33989 System Basis Chip With High Speed CAN Transceiver
MC33990 J1850 Serial Transceiver With Enhanced Ground
MC33990D Enhanced Class B Serial Transceiver
MC33991 Dual Gauge Driver Integrated Circuit
MC33991DW Gauge Driver Integrated Circuit
MC33993 22-MULTIPLE Switch Detection Interface
MC33993DWB MC33993
MC33996 16-Output Switch With Spi Controlthe 33996 is a 16-output Low-side Switch With a 24-bit Serial Input Control. It is Designed For ...
MC33997 3.3/5.0V Switching Power Supply
MC33997DW Switching Power Supply With Linear Regulators
MC33998 2.6/5.0V Switching Power Supply
MC33998DW Switching Power Supply With Linear Regulators
MC33999 16-Output Switch With Spi And PWM Control
MC3399DW Automotive Half-amp High-side Switch
MC3399T
MC34001 JFET Input Operational Amplifiers
MC34012-1 Telephone Tone Ringer
MC34014
MC34014DW Telepone Speech Network With Dialer Interface
MC34014P Telefone Speech Network With Dialer Interface
MC34016 Cordless Universal Telephone Interface
Same catergory

BQ2013H : Monitor/Supervisory. Nicd/nimh/lead-acid Gas Gauge For High Discharge Rates (>10a), Pgmable Offset Error & Load Comp..

KA7500B : SMPS Controller. Internal Regulator Provides a Stable 5V Reference Supply Trimmed to 5% Uncommitted Output TR for 200mA Sink or Source Current Output Control For Push-Pull or Single Ended Operation Variable Duty Cycle By Dead Time Control (Pin 4) Complete PWM Control Circuit On-Chip Oscillator With Master or Slave Operation Internal Circuit Prohibits Double Pulse at Either.

M62001FP : System reset.

MC79L18A : 3-Terminal 1A Negative Voltage Regulator. Output Current 100mA No External Components Internal Thermal Over Load Protection Internal Short Circuit Current Limiting Output Voltage Offered in 5% Tolerance Output Voltage -18V, -24V These regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. Parameter Input Voltage (for to -8V) (for to -18V).

MTB001 : Power Ics / Solenoid/motor Drivers (MTA,MTB Series). Four output driver per package TTL/CMOS compatible inputs (Low active) APPLICATION Head needle drive for printer Stepping motor drive for Output Voltage Output Current Reverse Voltage(flyback diode) Forward Current(each flyback diode) Forward Current(each common terminal) Output Current(each GND terminal) LogicSupplyVoltage LogicInputVoltage EnableInputVoltage.

MTD1120F : . Constant-current chopping function (Off time fixed, self-oscillation) 4-phase input (with inhibit for simultaneously turn ON) Built-in flywheel diodes Absolute Maximum Ratings (Ta=25) Item Symbol VCEO(SUS) Output Voltage IO Output Current VCC Logic@Supply@Voltage VIN Logic@Input@Voltage PT Total Power Dissipation Tj Junction Temperature Tstg Storage.

PKM4113PILA : DC/DC Converter. Advanced 126W DC/ DC Power Module 48 V Input; 12V Output High Efficiency 90% Typ Fast Dynamic Response, 150us, 100 mVpeak Typ Heatsinks available as an option for extended operation Low Output Ripple, 75mVp-p Typ High power density, 76.2 W/in3 Wide input voltage range (36-75V) according to ETSI s Industry standard footprint & pin-out 1,500 Vdc isolation.

TPS70751PWP : ti TPS70751, Dual-output Low-dropout (LDO) Voltage Regulator With Power up Sequencing.

TPS79425DCQ : ti TPS79425, Ultra-low Noise, High Psrr, Fast RF, High Enable, 250-mA Low Dropout Regulator.

UNR12-25W : Non-Isolated DC-DC Converters. 3.0-3.6V input range Non-isolated, or 1.8V output x 1" through-hole or SMT package Gull-wing leads/standard reflow for SMT Full synchronous-rectifier topology 300kHz switching; Planar magnetics High efficiency, to 89% Low noise, 80mVp-p Quick transient response, 25sec VOUT user-trimmable from to +50/55C ambient operation with no derating Remote on/off.

UPD16873 : Monolithic 3-aspect Spindle Motor Driver. is 3 aspect spindle motor driver that composed by CMOS control circuit and MOS bridge output. The consumption electric power can be substantially reduced to the screwdriver which used a conventional Bipolar transistor by the adoption of 3 aspect all-wave PWM methods and making an output paragraph MOSFET. Low On resistance. (The summation of the on resistance.

LM3410 : 525kHz/1.6MHz, Constant Current Boost And SEPIC LED Driver The LM3410 constant current LED driver is a monolithic, high frequency, PWM step-up DC/DC converter in 5-pin SOT23, 6-pin LLP, & 8-pin eMSOP packages. With a minimum of external components the LM3410 is easy to use. It can drive 2.5A typical peak currents with an internal 160m?? NMOS switch.

L6258E : Drivers For Motor Control PWM controlled high current DMOS universal motor driver.

STR-X6700 : Off-Line Quasi-Resonant Switching Regulators The STR-X6700 series integrates a quasi-resonant control IC and a MOSFET with avalanche guarantee. In normal operation, the device provides high efficiency and low EMI noise with bottom-skip quasi-resonant operation during light output loads. Low power consumption is also achieved by Auto-standby mode (not.

BQ25504 : Ultra Low Power Boost Converter With Battery Management For Energy Harvester App The bq25504 is the first of a new family of intelligent integrated energy harvesting Nano-Power management solutions that are well suited for meeting the special needs of ultra low power applications. The product is specifically designed to efficiently acquire and manage.

TLC59213 : 8-Channel Source Driver With Latch The TLC59213 and TLC59213A are 8-bit source drivers with input latch with CLK input and CLR to set the output OFF. The TLC59213 and TLC59213A have large output source currents up to 500 mA with Darlington transistor and collectors tied to VCC. These feature make the device optimum level of driving the matrix of ink jet printer.

 
0-C     D-L     M-R     S-Z