|
|
Part: BAT54C-7
Category:
Discrete
-> Transistors
-> FETs (Field Effect Transistors)
-> JFETs (Junction-FETs)
-> N-Channel
Description: N-channel Fet Synchronous Buck Regulator Controller For Low Output Voltages
Company: National Semiconductor Corporation
Datasheet: Download BAT54C-7 datasheet File size : 22 kB
Request For quote: Find where to buy BAT54C-7
Datasheet text preview:
LM2727/LM2737 N-Channel FET Synchronous Buck Regulator Controller for Low Output Voltages
June 2003
LM2727/LM2737 N-Channel FET Synchronous Buck Regulator Controller for Low Output Voltages
General Description
The LM2727 and LM2737 are high-speed, synchronous, switching regulator controllers. They are intended to control currents of 0.7A to 20A with up to 95% conversion efficiencies. The LM2727 employs output over-voltage and undervoltage latch-off. For applications where latch-off is not desired, the LM2737 can be used. Power up and down sequencing is achieved with the power-good flag, adjustable soft-start and output enable features. The LM2737 and LM2737 operate from a low-current 5V bias and can convert from a 2.2V to 16V power rail. Both parts utilize a fixedfrequency, voltage-mode, PWM control architecture and the switching frequency is adjustable from 50kHz to 2MHz by adjusting the value of an external resistor. Current limit is achieved by monitoring the voltage drop across the onresistance of the low-side MOSFET, which enhances low duty-cycle operation. The wide range of operating frequencies gives the power supply designer the flexibility to finetune component size, cost, noise and efficiency. The adaptive, non-overlapping MOSFET gate-drivers and high-side bootstrap structure helps to further maximize efficiency. The high-side power FET drain voltage can be from 2.2V to 16V and the output voltage is adjustable down to 0.6V.
Features
n Input power from 2.2V to 16V n Output voltage adjustable down to 0.6V n Power Good flag, adjustable soft-start and output enable for easy power sequencing n Output over-voltage and under-voltage latch-off (LM2727) n Output over-voltage and under-voltage flag (LM2737) n Reference Accuracy: 1.5% (0°C - 125°C) n Current limit without sense resistor n Soft start n Switching frequency from 50 kHz to 2 MHz n TSSOP-14 package
Applications
n n n n n Cable Modems Set-Top Boxes/ Home Gateways DDR Core Power High-Efficiency Distributed Power Local Regulation of Core Power
Typical Application
20049410
© 2003 National Semiconductor Corporation
DS200494
www.national.com
LM2727/LM2737
Connection Diagram
20049411
14-Lead Plastic TSSOP JA = 155°C/W NS Package Number MTC14
Pin Description
BOOT (Pin 1) - Supply rail for the N-channel MOSFET gate drive. The voltage should be at least one gate threshold above the regulator input voltage to properly turn on the high-side N-FET. LG (Pin 2) - Gate drive for the low-side N-channel MOSFET. This signal is interlocked with HG to avoid shoot-through problems. PGND (Pins 3, 13) - Ground for FET drive circuitry. It should be connected to system ground. SGND (Pin 4) - Ground for signal level circuitry. It should be connected to system ground. VCC (Pin 5) - Supply rail for the controller. PWGD (Pin 6) - Power Good. This is an open drain output. The pin is pulled low when the chip is in UVP, OVP, or UVLO mode. During normal operation, this pin is connected to VCC or other voltage source through a pull-up resistor. ISEN (Pin 7) - Current limit threshold setting. This sources a fixed 50µA current. A resistor of appropriate value should be connected between this pin and the drain of the low-side FET.
EAO (Pin 8) - Output of the error amplifier. The voltage level on this pin is compared with an internally generated ramp signal to determine the duty cycle. This pin is necessary for compensating the control loop. SS (Pin 9) - Soft start pin. A capacitor connected between this pin and ground sets the speed at which the output voltage ramps up. Larger capacitor value results in slower output voltage ramp but also lower inrush current. FB (Pin 10) - This is the inverting input of the error amplifier, which is used for sensing the output voltage and compensating the control loop. FREQ (Pin 11) - The switching frequency is set by connecting a resistor between this pin and ground. SD (Pin 12) - IC Logic Shutdown. When this pin is pulled low the chip turns off the high side switch and turns on the low side switch. While this pin is low, the IC will not start up. An internal 20µA pull-up connects this pin to VCC. HG (Pin 14) - Gate drive for the high-side N-channel MOSFET. This signal is interlocked with LG to avoid shootthrough problems.
www.national.com
2
LM2727/LM2737
Absolute Maximum Ratings
(Note 1)
Infrared or Convection (20sec) ESD Rating
235°C 2 kV
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VCC BOOTV Junction Temperature Storage Temperature Soldering Information Lead Temperature (soldering, 10sec) 260°C 7V 21V 150°C -65°C to 150°C
Operating Ratings
Supply Voltage (VCC) Junction Temperature Range Thermal Resistance (JA) 4.5V to 5.5V -40°C to +125°C 155°C/W
Electrical Characteristics
VCC = 5V unless otherwise indicated. Typicals and limits appearing in plain type apply for TA=TJ=+25°C. Limits appearing in boldface type apply over full Operating Temperature Range. Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Symbol Parameter Conditions VCC = 4.5V, 0°C to +125°C VCC = 5V, 0°C to +125°C VFB_ADJ FB Pin Voltage VCC = 5.5V, 0°C to +125°C VCC = 4.5V, -40°C to +125°C VCC = 5V, -40°C to +125°C VCC = 5.5V, -40°C to +125°C VON UVLO Thresholds Rising Falling SD = 5V, FB = 0.55V Fsw = 600kHz SD = 5V, FB = 0.65V Fsw = 600kHz SD = 0V FB Voltage Going Up FB Voltage Going Down SS Voltage = 2.5V 0°C to +125°C -40°C to +125°C 1 0.8 0.15 Min 0.591 0.591 0.591 0.589 0.589 0.589 Typ 0.6 0.6 0.6 0.6 0.6 0.6 4.2 3.6 1.5 1.7 0.4 6 6 20 8 5 11 11 95 35 28 50 50 65 65 15 15 2 mA 2.2 0.7 mA µs µs µA µA Max 0.609 0.609 0.609 0.609 0.609 0.609 V V Units
IQ-V5
Operating VCC Current
Shutdown VCC Current tPWGD1 tPWGD2 ISD ISS-ON PWGD Pin Response Time PWGD Pin Response Time SD Pin Internal Pull-up Current SS Pin Source Current
ISS-OC
SS Pin Sink Current During Over SS Voltage = 2.5V Current ISEN Pin Source Current Trip Point Error Amplifier Unity Gain Bandwidth Error Amplifier DC Gain Error Amplifier Slew Rate FB Pin Bias Current EAO Pin Current Sourcing and Sinking Error Amplifier Maximum Swing FB = 0.55V FB = 0.65V VEAO = 2.5, FB = 0.55V VEAO = 2.5, FB = 0.65V Minimum Maximum 0 0 0°C to +125°C -40°C to +125°C
µA µA
ISEN-TH
ERROR AMPLIFIER GBW G SR IFB IEAO VEA 5 60 6 15 30 2.8 0.8 1.2 3.2 100 155 MHz dB V/µA nA mA V
3
www.national.com
LM2727/LM2737
Electrical Characteristics
(Continued) VCC = 5V unless otherwise indicated. Typicals and limits appearing in plain type apply for TA=TJ=+25°C. Limits appearing in boldface type apply over full Operating Temperature Range. Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Symbol Parameter BOOT Pin Quiescent Current Conditions BOOTV = 12V, EN = 0 0°C to +125°C -40°C to +125°C BOOT-SW = 5V@350mA BOOT-SW = 5V@350mA BOOT-SW = 5V@350mA BOOT-SW = 5V@350mA Min Typ Max Units
GATE DRIVE IQ-BOOT 95 95 3 2 3 2 160 215 µA
RDS1 RDS2 RDS3 RDS4 OSCILLATOR
Top FET Driver Pull-Up ON resistance Top FET Driver Pull-Down ON resistance Bottom FET Driver Pull-Up ON resistance Bottom FET Driver Pull-Down ON resistance
RFADJ = 590k RFADJ = 88.7k fOSC PWM Frequency RFADJ = 42.2k, 0°C to +125°C RFADJ = 42.2k, -40°C to +125°C RFADJ = 17.4k RFADJ = 11.3k D Max Duty Cycle fPWM = 300kHz fPWM = 600kHz 500 490
50 300 600 600 1400 2000 90 88 2.6 3.5 % 700 700 kHz
LOGIC INPUTS AND OUTPUTS VSD-IH VSD-IL VPWGD-TH-LO SD Pin Logic High Trip Point SD Pin Logic Low Trip Point PWGD Pin Trip Points 0°C to +125°C -40°C to +125°C FB Voltage Going Down 0°C to +125°C -40°C to +125°C FB Voltage Going Up 0°C to +125°C -40°C to +125°C 1.3 1.25 0.413 0.410 0.691 0.688 V V 1.6 1.6 0.430 0.430 0.710 0.710 35 110 0.446 0.446 0.734 0.734
V
VPWGD-TH-HI
PWGD Pin Trip Points
V
VPWGD-HYS
PWGD Hysteresis (LM2737 only) FB Voltage Going Down FB Voltage Going Up
mV
Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device operates correctly. Opearting Ratings do not imply guaranteed performance limits. Note 2: The human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin.
www.national.com
4
LM2727/LM2737
Typical Performance Characteristics
Efficiency (VO = 1.5V) FSW = 300kHz, TA = 25°C Efficiency (VO = 3.3V) FSW = 300kHz, TA = 25°C
20049412
20049413
VCC Operating Current vs Temperature FSW = 600kHz, No-Load
Bootpin Current vs Temperature for BOOTV = 12V FSW = 600kHz, Si4826DY FET, No-Load
20049415 20049414
Bootpin Current vs Temperature with 5V Bootstrap FSW = 600kHz, Si4826DY FET, No-Load
PWM Frequency vs Temperature for RFADJ = 43.2k
20049416 20049417
5
www.national.com
Others parts begin by ba
BA-1 BA-2 BA-3 BA-4 BA-5 BA-6 BA-7 BA-8 BA-9 BA-10 BA-11 BA-12 BA-13 BA-14 BA-15 BA-16 BA-17 BA-18
|
|
|
