Details, datasheet, quote on part number: DS9622
PartDS9622
CategoryInterface and Interconnect => General Purpose Receivers
TitleGeneral Purpose Receivers
DescriptionDS9622 - Dual Line Receiver, Package: Lcc, Pin Nb=20
CompanyNational Semiconductor Corporation
DatasheetDownload DS9622 datasheet
Quote
Find where to buy
 
  

 

Features, Applications

The is a dual line receiver designed to discriminate a worst case logic swing of 2V from 10V common mode noise signal or ground shift. A 1.5V threshold is built into the differential amplifier to offer a TTL compatible threshold voltage and maximum noise immunity. The offset is obtained by use of current sources and matched resistors. The DS9622 allows the choice of output states with the input open, without affecting circuit performance by use A 130 terminating resistor is provided at the input of each line receiver. An enable is also provided for each line receiver. The output is TTL compatible. The output high level can be increased 12V by tying to a positive supply through a resistor. The output circuits allow wired-OR operation.

Features

TTL compatible threshold voltage Input terminating resistors Choice of output state with inputs open TTL compatible output High common mode Wired-OR capability Enable inputs Logic compatible supply voltages

Top View For Complete Military 883 Specifications, see RETS Datasheet. Order Number or DS9622MW/883 See NS Package Number or W14B

If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range Operating Temperature Range Lead Temperature (Soldering, 60 sec.) Internal Power Dissipation (Note V+ to GND Input Voltage 15V

Voltage Applied to Outputs for Output High State V- to GND Enable to GND

Symbol VOL Parameter Output Voltage LOW Conditions = -11V, VDIFF = 2.0V, IOL = 12.4 mA, EN = Open = 0V, VDIFF = 1.0V, IOH = -0.2 mA, EN = Open = 0V, VDIFF EN = Open = -10V, VDIFF EN = Open IN = Open, VI = Open, = -10V, VI+ = 0V, VI- = GND, S3 = Open = -10V, VI+ = GND, VI- EN = Open VIL(EN) Input Voltage LOW EN = Open VTH Differential Input Threshold Voltage VCM I+ I- Common Mode Voltage Terminating Resistance Positive Supply Current Negative Supply Current S3 = VI+ = 11V, VI- EN = Open -10V, 1.0V VDIFF mA -3.1 Min Max 0.4 Units V

Enable Input Leakage Current Enable Input Forward Current +Input Forward Current

Symbol Parameter SWITCHING CHARACTERISTICS = 25C tPLH tPHL Propagation Delay to High Level Propagation Delay to Low Level CL = (See

Note 1: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. Note 2: Unless otherwise specified Min/Max limits apply across the to +125C temperature range. All typicals are given for VCC = 5V and = 25C. Note 3: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to ground unless otherwise specified. Note 4: Only one output at a time should be shorted. Note 5: Rating applies to ambient temperatures to +125C. Above 125C ambient, derate linearity at 120C/W.


 

Related products with the same datasheet
5962-8752201CA
DS9622MJ/883
DS9622MW/883
Some Part number from the same manufacture National Semiconductor Corporation
DS9622ME/883 Dual Line Receiver
DS9622MJ/883 DS9622 - Dual Line Receiver, Package: Lcc, Pin Nb=20
DS9627 DS9627 - Dual Line Receiver, Package: Cerdip, Pin Nb=16
DS9627MJ/883 Dual Line Receiver
DS9636A DS9636A - RS-423 Dual Programmable Slew Rate Line Driver, Package: Cerdip, Pin Nb=8
DS9637A DS9637A - Dual Differential Line Receiver, Package: Soic Narrow, Pin Nb=8
DS9637ACMDC
DS9637ACMX DS9637A - Dual Differential Line Receiver, Package: Soic Narrow, Pin Nb=8
DS9637AMMD8
DS9638 DS9638 - RS-422 Dual High Speed Differential Line Driver, Package: Soic Narrow, Pin Nb=8
DS9638MJ/883 Rs-422 Dual High Speed Differential Line Driver
DS9639A Dual Differential Line Receiver
DS96F172C Eia-485/eia-422 Quad Differential Drivers
DS96F172CN Quad Differential Drivers
DS96F172M DS96F172M - EIA-485/EIA-422 Quad Differential Drivers, Package: Lcc, Pin Nb=20
DS96F172ME/883 Quad Differential Drivers
DS96F172MJ DS96F172M - EIA-485/EIA-422 Quad Differential Drivers, Package: Lcc, Pin Nb=20
DS96F172MW/883 Quad Differential Drivers
DS96F173C Quad Differential Receivers
DS96F173CJ
DS96F173M DS96F175M - RS-485/RS-422 Quad Differential Receiver, Package: Lcc, Pin Nb=20

54LS109N : Dual Positive-edge-triggered J-k Flip-flops With Preset, Clear, And Complementary Outputs

COP8SGE528M8CKY :

LM3711XKMM-463 : Supervisory Function LM3710 - Microprocessor Supervisory Circuits With Power Fail Input, Low Line Output, Manual Reset And Watchdog Timer, Package: Microsmd, Pin Nb=9

LM6181AMJ/883 : LM6181 - 100 MA, 100 MHZ Current Feedback Amplifier, Package: Soic Narrow, Pin Nb=16

LM748CJ : LM748 - Operational Amplifier, Package: TO-5, Pin Nb=8

MM54C74J : Dual D Flip-flop

DS16EV5110 : The DS16EV5110 is a 2.25 Gbps multi-channel equalizer optimized for video cable extension applications. It contains three transition-minimized differential signaling (TMDS) data channels and one clock channel as commonly found in DVI and HDMI cables. It provides compensation for skin-effect and diel

COP8SGH628M3 : 8-bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and Usart

PAL20L8C : Progammable Array Logic Series 24 (PAL Series 24)

COP8SGR044N7 : 8-bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and Usart

LMP8640HVMKE-T : Precision High Voltage Current Sense Amplifier The LMP8640 and the LMP8640HV are precision current sense amplifiers that detect small differential voltages across a sense resistor in the presence of high input common mode voltages with a supply voltage range from 2.7V to 12V. The LMP8640 accepts

LMR12010YMK/NOPB : SIMPLE SWITCHER 20Vin, 1A Step-Down Voltage Regulator In SOT-23 The LMR12010 regulator is a monolithic, high frequency, PWM step-down DC/DC converter in a 6-pin Thin SOT23 package. It provides all the active functions to provide local DC/DC conversion with fast transient response and accurate regul

 
0-C     D-L     M-R     S-Z