Details, datasheet, quote on part number: DS96F172MJ
CategoryInterface and Interconnect => RS-485
DescriptionDS96F172M - EIA-485/EIA-422 Quad Differential Drivers, Package: Lcc, Pin Nb=20
CompanyNational Semiconductor Corporation
DatasheetDownload DS96F172MJ datasheet
Cross ref.Similar parts: AM26C31, AM26C31-EP, AM26C31M, AM26C32, AM26C32-EP, AM26C32M, AM26LS31, AM26LS31M, AM26LS32A, AM26LS32AC
Find where to buy


Features, Applications

The DS96F172 and the DS96F174 are high speed quad differential line drivers designed to meet EIA-485 Standards. The DS96F172 and the DS96F174 offer improved performance due to the use of L-FAST bipolar technology. The use of LFAST technology allows the DS96F172 and DS96F174 to operate at higher speeds while minimizing power consumption. The DS96F172 and the DS96F174 have TRI-STATE outputs and are optimized for balanced multipoint data bus transmission at rates to 15 Mbps. The drivers have wide positive and negative common mode range for multipoint applications in noisy environments. Positive and negative current-limiting is provided which protects the drivers from line fault conditions over to -7.0V common mode range. A thermal shutdown feature is also provided. The DS96F172 features an active high and active low Enable, common to all four drivers. The DS96F174 features separate active high Enables for each driver pair.


Meets EIA-485 and EIA-422 standards Monotonic differential output switching TRI-STATE outputs Designed for multipoint bus transmission Common mode output voltage range: to +12V Operates from single +5.0V supply Reduced power consumption Thermal shutdown protection DS96F172 and DS96F174 are lead and function compatible with the SN75172/174 or the AM26LS31/MC3487 Military temperature range available Qualified for MIL-STD-883C Standard military drawings available (SMD) Available in DIP (J), LCC (E), and Flatpak (W) packages

H = High Level L = Low Level X = Don't Care Z = High Impedance (Off)
TRI-STATE is a registered trademark of National Semiconductor Corporation.

Specifications for the 883 version of this product are listed separately on the following pages. Storage Temperature Range (TSTG) to +175C Lead Temperature (Soldering, 60 sec.) 300C Maximum Package Power Dissipation (Note at 25C Ceramic DIP (J) 1500 mW Supply Voltage 7.0V Enable Input Voltage 5.5V

Min Supply Voltage (VCC) DS96F174C Common Mode Output Voltage (VOC) Output Current HIGH (IOH) Output Current LOW (IOL) Operating Temperature (TA) 4.75 -7.0 Typ 5.0 Max Units V mA

Over recommended supply voltage and operating temperature range, unless otherwise specified Symbol VIH VIL VOH VOL VIC |VOD1| |VOD2| Parameter Input Voltage HIGH Input Voltage LOW Output Voltage HIGH Output Voltage LOW Input Clamp Voltage Differential Output Voltage Differential Output Voltage IOH -33 mA IOL = 54, Figure = 100, Figure 1 VOD |VOD| VOC |VOC| IO IOZ IIH IIL IOS Differential Output Voltage Change in Magnitude of Differential Output Voltage (Note 5) Common Mode Output Voltage (Note 6) Change in Magnitude of Common Mode Output Voltage (Note 5) Output Current with Power Off High Impedance State Output Current Input Current HIGH Input Current LOW Short Circuit Output Current (Note 7) VCC VO = VCC = +12V ICC ICCX Supply Current (All Drivers) No Load Outputs Enabled Outputs Disabled to +70C Conditions Min 0.8 0.7 Typ (Note 2) Max Units

VCC = 25C Symbol tDD tTD tPLH tPHL tZH tZL tHZ tLZ tLZL tSKEW Parameter Differential Output Delay Time Differential Output Transition Time Propagation Delay Time, Low-to-High Level Output Propagation Delay Time, High-to-Low Level Output Enable Time to High Level Output Enable Time to Low Level Output Disable Time from High Level Output Disable Time from Low Level Output Disable Time from Low Level with Load Resistor to GND (Note 8) Driver Output to Output RL ns

Note 2: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. Note 3: Unless otherwise specified min/max limits apply across the to +70C range for the DS96F174C. All typicals are given for VCC = 5V and = 25C. Note 4: All currents into the device pins are positive; all currents out of the device pins are negative. All voltages are reference to ground unless otherwise specified. Note 5: |VOD| and |VOC| are the changes in magnitude of VOD and VOC respectively, that occur when the input is changed from a high level to a low level. Note In EIA-422A and EIA-485 standards, VOC, which is the average of the two output voltages with respect to ground, is called output offset voltage, VOS. Note 7: Only one output at a time should be shorted. Note 8: For more information see Application Bulletin, contact Product Marketing.


Related products with the same datasheet
Some Part number from the same manufacture National Semiconductor Corporation
DS96F172MJ/883 DS96F172M - EIA-485/EIA-422 Quad Differential Drivers, Package: Lcc, Pin Nb=20
DS96F172MW/883 Quad Differential Drivers
DS96F173C Quad Differential Receivers
DS96F173M DS96F175M - RS-485/RS-422 Quad Differential Receiver, Package: Lcc, Pin Nb=20
DS96F173ME/883 Quad Differential Receivers
DS96F173MJ DS96F175M - RS-485/RS-422 Quad Differential Receiver, Package: Lcc, Pin Nb=20
DS96F173MW/883 Quad Differential Receivers
DS96F174C DS96F172M - EIA-485/EIA-422 Quad Differential Drivers, Package: Lcc, Pin Nb=20
DS96F174ME/883 Quad Differential Drivers
DS96F174MJ DS96F172M - EIA-485/EIA-422 Quad Differential Drivers, Package: Lcc, Pin Nb=20
DS96F174MW-MLS DS96F172M - EIA-485/EIA-422 Quad Differential Drivers, Package: Lcc, Pin Nb=20
DS96F175C DS96F175M - RS-485/RS-422 Quad Differential Receiver, Package: Lcc, Pin Nb=20
DS96F175ME/883 Quad Differential Receivers
DS96F175MJ DS96F175M - RS-485/RS-422 Quad Differential Receiver, Package: Lcc, Pin Nb=20
DS96F175MJ/883 Quad Differential Receivers
DS96F175MW-MLS DS96F175M - RS-485/RS-422 Quad Differential Receiver, Package: Lcc, Pin Nb=20
DSV14196 DSV14196 - +3.3V Supply EIA/TIA-232 5 Driver X 3 Receiver, Package: Soic Wide, Pin Nb=20
E503PCASM Clc503 Evaluation Board
E935PCASM Clc935 Evaluation Boards

DM7474 : Bipolar->TTL Family Dual Positive-edge-triggered D Flip-flops With Preset, Clear And Complementary Outputs

JM38510/11201SCA : LM139 - Low Power Low Offset Voltage Quad Comparator, Package: Lcc, Pin Nb=20

LM6321M : High Speed Buffer

LMV715 : Rail to Rail Input LMV710 - Low Power, Rrio Operational Amplifiers With High Output Current Drive And Shutdown Option, Package: SOT-23, Pin Nb=5

LM2657MTCX : Dual Synchronous Buck Regulator Controller The LM2657 is an adjustable 200kHz-500kHz dual channel voltage-mode controlled high-speed synchronous buck regulator controller ideally suited for high current applications. The LM2657 requires only N-channel FETs for both the upper and lower positions of

MM54HCT76 : Dual J-K Flip-flops with Preset and Clear

VJ0805A102CXXAT2L : Synchronous Buck Controller with Pre-bias Startup, and Optional Clock Synchronization

VJ1206A102DLXAT68 : N-channel FET Synchronous Buck Regulator Controller for Low Output Voltages

LP3874EMPX-2.5 : 0.8A Fast Ultra Low Dropout Linear Regulators

COP8SGF728Q3 : 8-bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and Usart

LM117HP+ : 3-terminal Adjustable Regulator

0-C     D-L     M-R     S-Z