Details, datasheet, quote on part number: DS96F175C
PartDS96F175C
CategoryInterface and Interconnect => RS-485
DescriptionDS96F175M - RS-485/RS-422 Quad Differential Receiver, Package: Lcc, Pin Nb=20
CompanyNational Semiconductor Corporation
DatasheetDownload DS96F175C datasheet
Quote
Find where to buy
 
  

 

Features, Applications

The DS96F173 and the DS96F175 are high speed quad differential line receivers designed to meet the EIA-485 standard. The DS96F173 and the DS96F175 offer improved performance due to the use of L-FAST bipolar technology. The use of LFAST technology allows the DS96F173 and DS96F175 to operate at higher speeds while minimizing power consumption. The DS96F173 and the DS96F175 have TRI-STATE outputs and are optimized for balanced multipoint data bus transmission at rates to 15 Mbps. The receivers feature high input impedance, input hysteresis for increased noise immunity, and input sensitivity 200 mV over a common mode input voltage range to +12V. The receivers are therefore suitable for multipoint applications in noisy environments. The DS96F173 features an active high and active low Enable, common to all four receivers. The DS96F175 features separate active high Enables for each receiver pair.

Features

Meets EIA-422A, EIA-423A standards Designed for multipoint bus applications TRI-STATE outputs Common mode input voltage range: to +12V Operates from single +5.0V supply Reduced power consumption (ICC 50 mA max) Input sensitivity 200 mV over common mode range Input hysteresis 50 mV typical High input impedance Military temperature range available Qualified for MIL STD 883C Available to standard military drawings (SMD) Available in DIP(J), LCC(E), and FlatPak (W) packages DS96F173 and DS96F175 are lead and function compatible with SN75173/175 or the AM26LS32/MC3486

H = High Level L = Low Level Z = High Impedance (off) X = Don't Care
TRI-STATE is a registered trademark of National Semiconductor Corporation.

Specifications for the 883 version of this product are listed separately. Storage Temperature Range (TSTG) to +175C Lead Temperature (Soldering, 60 sec.) 300C Max. Package Power Dissipation (Note at 25C Ceramic DIP (J) 1500 mW Supply Voltage 25V Input Voltage, or B Inputs 25V Differential Input Voltage Enable Input Voltage 7.0V Low Level Output Current 50 mA

Min Supply Voltage (VCC) DS96F175C Common Mode Input Voltage (VCM) Differential Input Voltage (VID) Output Current HIGH (IOH) Output Current LOW (IOL) Operating Temperature (TA) 4.75 -7 Typ 5.0 Max Units mA C

Electrical Characteristics (Notes 3, 4) Over recommended supply voltage and operating temperature ranges, unless otherwise specified

Symbol VTH VTL VTH - VTL VIH VIL VIC VOH VOL IOZ II IIH IIL RI IOS ICC ICCX Parameter Differential-Input High Threshold Voltage Differential-Input (Note 5) Low Threshold Voltage Hysteresis (Note 6) Enable Input Voltage HIGH Enable Input Voltage LOW Enable Input Clamp Voltage Output Voltage HIGH Output Voltage LOW High-Impedance State Output Line Input Current (Note 7) Enable Input Current HIGH Enable Input Current LOW Input Resistance Short Circuit Output Current Supply Current (Note 8) No Load Outputs Enabled Outputs Disabled -18 mA VID 200 mV IOH -400 A VID to 2.4V Other Input = 0V VIH = 2.7V VIL to +125C IOL 8.0 mA IOL 11 mA VCM VO = VOL VO = VOH Conditions Min Typ Max 0.2 Units V

VCC = 25C Symbol tPLH tPHL tZH tZL tHZ Parameter Propagation Delay Time, Low to High Level Output Propagation Delay Time, High to Low Level Output Enable Time to High Level Output Enable Time to Low Level Output Disable Time from High Level = 15 pF, Figure = 15 pF, Figure = 5.0 pF, Figure ns Conditions VID = 15 pF, Figure 1 VCM 22 ns Min 5.0 Typ 15 Max 22 Units ns

Output Disable Time from Low Level Pulse Width Distortion (SKEW)

Note 2: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. Note 3: Unless otherwise specified min/max limits apply across the to +70C range for the DS96F175C. All typicals are given for VCC = 5V and = 25C. Note 4: All currents into the device pins are positive; all currents out of the device pins are negative. All voltages are reference to ground unless otherwise specified. Note 5: The algebraic convention, when the less positive (more negative) limit is designated minimum, is used in this data sheet for common mode input voltage and threshold voltage levels only. Note 6: Hysteresis is the difference between the positive-going input threshold voltage. VTH, and the negative going input threshold voltage, VTL. Note 7: Refer to EIA-485 Standard for exact conditions. Note 8: Only one output at a time should be shorted.


 

Related products with the same datasheet
5962-9076601MEA
5962-9076601MFA
5962-9076602M2A
5962-9076602MEA
5962-9076602MFA
DS96F173M
DS96F173MJ
DS96F173MJ/883
DS96F175CJ
DS96F175M
DS96F175MJ
Some Part number from the same manufacture National Semiconductor Corporation
DS96F175CJ DS96F175M - RS-485/RS-422 Quad Differential Receiver, Package: Lcc, Pin Nb=20
DS96F175ME/883 Quad Differential Receivers
DS96F175MJ DS96F175M - RS-485/RS-422 Quad Differential Receiver, Package: Lcc, Pin Nb=20
DS96F175MJ/883 Quad Differential Receivers
DS96F175MW-MLS DS96F175M - RS-485/RS-422 Quad Differential Receiver, Package: Lcc, Pin Nb=20
DSV14196 DSV14196 - +3.3V Supply EIA/TIA-232 5 Driver X 3 Receiver, Package: Soic Wide, Pin Nb=20
E503PCASM Clc503 Evaluation Board
E935PCASM Clc935 Evaluation Boards
E949PCASM Clc949 Evaluation Board
EL2074 CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
EL2232 CLC431 - Dual Wideband Monolithic op Amp With Disable, Package: Lcc, Pin Nb=20
F100145
F100322 Low Power 9-bit Buffer
F100328 Low Power Octal Ecl/ttl Bi-directional Translator With Latch
F100329 Low Power Octal Ecl/ttl Bidirectional Translator With Register
F100331 Low Power Triple D Flip-flop
F100364 Low Power 16-input Multiplexer
F100371 Low Power Triple 4-input Multiplexer With Enable
F100402
F100422
F1212
 
0-C     D-L     M-R     S-Z