Details, datasheet, quote on part number: FPD87392AXA
Description+3.3V Tft-lcd Timing Controller For Dual LVDS Inputs/dual RSDS Outputs For Tft-lcd Monitor And Notebook Not Recommended For New ...
CompanyNational Semiconductor Corporation
DatasheetDownload FPD87392AXA datasheet
Find where to buy


Features, Applications

FPD87392AXA +3.3V TFT-LCD Timing Controller with Dual LVDS Inputs/Dual RSDSTM Outputs for TFT-LCD Monitor and Notebook (SXGA/SXGA+/UXGA)

The FPD87392AXA Panel Timing Controller is an integrated FPD-Link + RSDSTM + TFT-LCD Timing Controller. The logic architecture is implemented using standard and default timing controller functionality based on an Embedded Gate Array. The device is reconfigurable to the needs of a specific application by providing user-defined specifications or customer supplied VHDL/Verilog code. The is a timing controller that combines an LVDS dual pixel input interface with National's Reduced Swing Differential Signaling (RSDSTM) output column driver interface for SXGA, SXGA+ and UXGA resolutions. It resides on the TFT-LCD panel and provides the data buffering and control signal generation. The RSDSTM data path to the column driver contributes toward lowering radiated EMI and reduced system dynamic power consumption. The RSDSTM dual 12 pair differential bus conveys to 24-bit color data for SXGA/SXGA+/UXGA panels when using VESA 60Hz standard timing.


n Input frequency range from 30 MHz to 85 MHz n Support display resolutions SXGA (1280x1024), SXGA+ (1400x1050) and UXGA (1600x1200) n Embedded gate array for custom panel timing n RSDSTM (Reduced Swing Differential Signaling) Column Driver bus for low power and reduced EMI n Drives RSDSTM column driver to 170 Mb/s with an 85 MHz clock or 8 bit LVDS dual pixel input interface (FPD-Link) n Virtual 8-bit color depth in FRC mode n Flexible RSDSTM data output mapping for Bottom or Top mount n Supports 1 and 2 line inversion mode for RVS output n Supports Graphics Controllers with spread spectrum interface for lower EMI n Free Run Mode Function n Fail-safe function in DE mode (Bonding Option) n Supports DE mode and SYNC only mode (Bonding Option) n Power-On-Reset Support n CMOS circuitry operates from to 3.6V supply n Operation frequency: 54 MHz (max) @ VCC: 3.0V n Operation frequency: 85 MHz (max) @ VCC: n 128 TQFP package with body size 1.0mm, 0.4mm Pitch

DUAL FPD-LINK RECEIVERS The LVDS based FPD-Link Receivers inputs video data and control timing through 8 pairs of LVDS channels plus 2 pairs of LVDS clocks to provide 24-bit color or use only 6 pairs of LVDS channels plus 2 LVDS clocks to provide 18-bit color. The video data is converted to a parallel data stream and routed to the 8-6 bit translator. SPREAD SPECTRUM SUPPORT The FPD-Link receiver supports graphics controllers with Spread Spectrum interfaces for reducing EMI. The Spread Spectrum methods supported are Center and Down Spread. A maximum of 2% total is supported at a frequency modulation of 100kHz maximum. 8-6 BIT TRANSLATOR 8-bit data is reduced a 6-bit data path via a time multiplexed dithering technique or simple truncation of the LSBs. This function is enabled via the input control pins. DATAPATH BLOCK AND RSDS TRANSMITTER 6(8)-bit video data (RGB) is input to the Datapath Block supports an 85 MHz dual pixel rate. The data is delayed to align the Column Driver Start Pulse (STH) with the Column Driver data. The dual data bus RSG[3:0]P/N, RSB[3:0]P/N) outputs a 170 MHz rate on 24 differential output channels. The clock is output on the (Front, Back) RSCKP/N differential pairs. The RSDS Column Drivers latch data on both positive and negative edges of the clock. The swap function provides flexible RSDS data output mappings for either Top or Bottom mount. The RSDS output setup/hold timings are also adjustable through the RSKEW[2:0] input pins. TIMING CONTROL FUNCTION The Timing Control function generates control to Column Drivers, Row Drivers, and power supply. The GPOs (General Purpose Outputs) provide for CD latch pulse, REV, and Row Driver control generation. The General Purpose Outputs allow the user to generate control anywhere within the frame data. Standard Row Driver interface or Custom Row Driver interfaces can be implemented with the GPOs (General Purpose Outputs). RSDS OUTPUT VOLTAGE CONTROL The RSDS output voltage swing is controlled through an external load resistor connected to the RPI pin. The RSDS output signal levels can be adjusted to suit the particular application. This is dependent on overall LCD module design characteristics such as trace impedance, termination, etc. The RSDS output voltage is inversely related to the RPI value. Lower RPI values will increase the RSDS output voltage swing and consequently overall power consumption will also increase.


Related products with the same datasheet
Some Part number from the same manufacture National Semiconductor Corporation
FPD87392AXAVQ +3.3V Tft-lcd Timing Controller For Dual LVDS Inputs/dual RSDS Outputs For Tft-lcd Monitor And Notebook Not Recommended For New ...
G1-200B-85-1.6 Processor Series Low Power Integrated X86 Solution
GD54LS08 54LS08 - Quad 2-Input And Gate, Package: Lcc, Pin Nb=20
GD54LS161A DM54LS161A - Synchronous 4-Bit Binary Counter With Asynchronous Clear, Package: Cerdip, Pin Nb=16
GD54LS175 DM54LS175 - Quad D Flip-flop With Clear And Complementary Outputs, Package: Cerpack, Pin Nb=16
GD54LS32 DM54LS32 - Quad 2-Input OR GATE, Package: Lcc, Pin Nb=20
GEODEGXLVPROCESSORSeries Low Power Integrated X86 Solution
GEODEGXMPROCESSOR Integrated X86 Solution With Mmx(tm) Support
GL-166B-85-2.2 Geode Processor Series Low Power Integrated X86 Solutions
GM-180B-70 Geode Processor Integrated X86 Solution With MMX Support
GS9000 CLC011 - Serial Digital Video Decoder, Package: Plcc, Pin Nb=28

5962-9230601MXA : Military/Aerospace->ECL 100336 - Low Power 4-Stage Counter/shift Register, Package: Cerquad, Pin Nb=24

ADC12L066CIVY : ADC12L066 - 12-Bit, 66 Msps, 450 MHZ Bandwidth A/D Converter With Internal Sample-and-Hold, Package: Lqfp, Pin Nb=32

JM38510R76203BEA : Military/Aerospace->FACT AC 54AC157 - Quad 2-Input Multiplexer, Package: Lcc, Pin Nb=20

LM1815 : LM1815 - Adaptive Variable Reluctance Sensor Amplifier, Package: Soic Narrow, Pin Nb=14

LM2677LD-3.3 : LM2677 - Simple Switcher High Efficiency 5A Step-down Voltage Regulator With Sync, Package: Llp, Pin Nb=14

LM2700MT-ADJ : LM2700 - 600kHz/1.25MHz, 2.5A, Step-up PWM DC/DC Converter, Package: Llp, Pin Nb=14

LP2985IM5X-6.1 : Positive Voltage->Fixed LP2985LV - Micropower 150 ma Low-noise Low-dropout Regulator in SOT-23 And Micro SMD Packages For Applications With Output Voltages Less_than_or_equal 2.3V, Package: Microsmd, Pin Nb=5

COP8SGB540V9 : 8-bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory, Two Comparators and Usart

Same catergory

AM29F040-120 : . 4 Megabit x 8-Bit) CMOS 5.0 Volt-only, Sector Erase Flash Memory 10% for read and write operations Minimizes system level power requirements s Compatible with JEDEC-standards Pinout and software compatible with singlepower-supply Flash Superior inadvertent write protection s Package options 32-pin PLCC 32-pin TSOP 32-pin PDIP s Minimum 100,000 write/erase.

E0C6007 : CISC->CISC Arch. 4-bit Single Chip Microcomputer.

IR6226 : Intelligent High Side MOSFET Power Switch. INTELLIGENT HIGH SIDE MOSFET POWER SWITCH Current Limit for Short Circuit Protection Over-Temperature Protection Active Output Negative Clamp Reverse Battery Protection for Logic Circuit Broken Ground Protection Short to VCC Protection Low Noise Charge Pump Sleep Mode Supply Current 4kV ESD Protection On All Pins Logic Ground Isolated From Power Ground.

OVSR9CBCR8 : Blue-green Side-emitting SMD LED (4 x 4 mm, 120 Viewing Angle). Compact size allows use in space conscious devices Thin profile offers unlimited design flexibility Long life span reduces maintenance cost Suitable for all SMT assembly methods Blue-green (505 nm) water clear lens The is a side-looking blue-green mm 120 surface-mounted LED that can be used as a light source in many applications. Its compact size and thin.

226E : GaAs MMIC +3V Sot26 Transmit Receive Switch, DC - 2.0 GHz. Typical Applications Low Insertion Loss: 0.6 dB Ultra Small Package: SOT26 High Input to +38 dBm High Input to +61 dBm The & HMC226E are low-cost SPDT switches 6-lead SOT26 packages for use in transmit-receive applications which require very low distortion at high signal power levels. The device can control signals from to 2.0 GHz and is especially.

E2UKB18-20.000M-CXA : Crystal. RoHS Compliant (Pb-Free) HC-49/US package or BT cut available Resistance weld seal Tight tolerance/stability Tape and reel, insulator tab, and custom lead length options available Frequency Range Frequency Tolerance / Stability Over Operating Temperature Range Operating Temperature Range Aging (at 25C) Storage Temperature Range Shunt Capacitance Insulation.

XO54ETFH60100 : Half Size Clock Oscillators Enable/disable. The XO-523 series oscillator is half size, has Tri-state enable/disable controlled function, and is with 3.3 V power supply voltage. The metal package with pin#4 case ground acts as shielding to minimize EMI radiation. 8 pin half size Industry standard Wide frequency range Low cost Resistance weld package 3.3 V Lead (Pb)-free terminations and RoHS compliant.

LDECC1820 : Pen-pet H.T. The part number, comprising 14 digits, is formed as follows: Digit to 3 Series code (L = leadless; DE = polyester family) Digit 4 d.c. or a.c. rated voltage (VR). P =630Vdc Digit 5 Size code: Series Rated voltage = 50Vdc) Size code = 22.20) Capacitance = 0.47F Tolerance = 5%) Dielectric (A = PEN) Version (5 = standard) Packing (N= Tape) Internal use Digits.

SD1100C1111 : N Channel Enhancement MODE HIGH Voltage D MOS Power FETS.

GRM0336R1E820GD01D : 82pF Ceramic Capacitor 0201 (0603 Metric) 25V; CAP CER 82PF 25V 2% R2H 0201. s: Capacitance: 82pF ; Voltage - Rated: 25V ; Tolerance: 2% ; Package / Case: 0201 (0603 Metric) ; Temperature Coefficient: R2H ; Packaging: Tape & Reel (TR) ; : - ; Lead Spacing: - ; Operating Temperature: -55C ~ 125C ; Mounting Type: Surface Mount, MLCC ; Lead Free.

7-1437655-3 : Through Hole Terminal Block - Barrier Block Connectors, Interconnect Through Hole; CONN BARRIER BLOCK 12CIRC 9.53MM. s: Color: Black ; Mounting Type: Through Hole ; Number of Rows: 1 ; Pitch: 0.375" (9.53mm) ; Terminal Block Type: Barrier Block ; Number of Circuits: 12 ; : - ; Current: 25A ; Voltage: 300V ; Wire Gauge: 12-22 AWG ; Top Termination: Screws.

A9BBG-1102F : Ffc, Fpc (flat Flexible) Cable Assembly 2.0" (50.8mm); FLEX CABLE - AFF11G/AF11/AFF11G. s: Pitch: 0.100" (2.54mm) ; Contact Termination: Receptacle to Receptacle ; Length: 2.0" (50.8mm) ; Number of Positions: 11 ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.

BH4AAW : Battery Holders, Clips, Contact Battery Product; HOLDER BATT 4-AA CELLS WIRE LDS. s: Number of Cells: 4 ; Battery Cell Size: AA ; Termination Style: Wire Leads - 6" (152.4mm) ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.

U65-E04-5120-T : Gold Surface Mount, Right Angle Pluggable Connectors, Interconnect Surface Mount, Right Angle; CONN RECEPT 4X SCREWLOCK SMD PCB. s: Mounting Type: Surface Mount, Right Angle ; Connector Type: Multi-Standard Pluggable 4x ; Number of Positions: 8 Signal Pairs ; : Board Guide, Flange ; Packaging: Cut Tape (CT) ; Contact Finish: Gold ; Connector Style:.

EL817(M)(D) : Optoisolator - Transistor, Photovoltaic Output Channel Through Hole 4-DIP (0.400", 10.16mm); PHOTOCOUPLER PHOTOTRANS 4DIP. s: Voltage - Isolation: 5000Vrms ; Input Type: DC ; Output Type: Transistor ; Current - Output / Channel: 50mA ; Voltage - Output: 35V ; Vce Saturation (Max): 200mV ; Current Transfer Ratio (Min): 300% @ 5mA ; Mounting Type: Through.

4-1625984-1 : 2.2K Ohm 50W Chassis Mount Resistors; RES 2.2K OHM 50W 5% WW LUG. s: Resistance (Ohms): 2.2K ; Power (Watts): 50W ; Composition: Wirewound ; : - ; Temperature Coefficient: 30ppm/C ; Tolerance: 5% ; Size / Dimension: 2.008" L x 1.181" W (51.00mm x 30.00mm) ; Height: 0.669" (17.00mm) ; Coating, Housing Type: Aluminum ; Mounting Feature: Flanges ; Packaging:.

RUB002N02T2CL : 200 mA, 20 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET. s: Polarity: N-Channel ; MOSFET Operating Mode: Enhancement ; V(BR)DSS: 20 volts ; rDS(on): 1.4 ohms ; Package Type: VMN3, 3 PIN ; Number of units in IC: 1.

0-C     D-L     M-R     S-Z