|
Details, datasheet, quote on part number:JM38510/76207BFA
| |
Datasheet text preview:
54AC257 · 54ACT257 Quad 2-Input Multiplexer with TRI-STATE Outputs
July 1998
54AC257 · 54ACT257 Quad 2-Input Multiplexer with TRI-STATE ® Outputs
General Description
The 'AC/'ACT257 is a quad 2-input multiplexer with TRI-STATE outputs. Four bits of data from two sources can be selected using a Common Data Select input. The four outputs present the selected data in true (noninverted) form. The outputs may be switched to a high impedance state by placing a logic HIGH on the common Output Enable (OE) input, allowing the outputs to interface directly with bus-oriented systems.
Features
n n n n n n ICC and IOZ reduced by 50% Multiplexer expansion by tying outputs together Noninverting TRI-STATE outputs Outputs source/sink 24 mA 'ACT257 has TTL-compatible inputs Standard Military Drawing (SMD) -- 'AC257: 5962-88703 -- 'ACT257: 5962-89689
Logic Symbols
IEEE/IEC
DS100286-1
DS100286-2
Pin Names S OE I0a I0d I1a I1d Za Zd
Description Common Data Select Input TRI-STATE Output Enable Input Data Inputs from Source 0 Data Inputs from Source 1 TRI-STATE Multiplexer Outputs
TRI-STATE ® is a registered trademark of National Semiconductor Corporation. FACTTM is a trademark of Fairchild Semiconductor Corporation.
© 1998 National Semiconductor Corporation
DS100286
www.national.com
Connection Diagrams
Pin Assignment for DIP and Flatpak
Functional Description
The 'AC/'ACT257 is quad 2-input multiplexer with TRI-STATE outputs. It selects four bits of data from two sources under control of a Common Data Select input. When the Select input is LOW, the I0x inputs are selected and when Select is HIGH, the I1x inputs are selected. The data on the selected inputs appears at the outputs in true (noninverted) form. The device is the logic implementation of a 4-pole, 2-position switch where the position of the switch is determined by the logic levels supplied to the Select input. The logic equations for the outputs are shown below: Za = OE · (11a · S + I0a · S) Zb = OE · (11b · S + I0b · S) Zc = OE · (11c · S + I0c · S) Zd = OE · (11d · S + I0d · S) When the Output Enable (OE) is HIGH, the outputs are forced to a high impedance state. If the outputs are tied together, all but one device must be in the high impedance state to avoid high currents that would exceed the maximum ratings. Designers should ensure the Output Enable signals to TRI-STATE devices whose outputs are tied together are designed so there is no overlap.
DS100286-3
Pin Assignment for LCC
Truth Table
Output Enable OE H
DS100286-4
Select Input S X H H L L I0 X X X L H
Data Inputs I1 X L H X X
Outputs Z Z L H L H
L L L L
H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Z = High Impedance
Logic Diagram
DS100286-5
Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays.
www.national.com
2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) DC Input Diode Current (IIK) VI = -0.5V VI = VCC +0.5V DC Input Voltage (VI) DC Output Diode Current (IOK) VO = -0.5V VO = VCC +0.5V DC Output Voltage (VO) DC Output Source or Sink Current (IO) DC VCC or Ground Current Per Output Pin (ICC or IGND) Storage Temperature (TSTG) Junction Temperature (TJ) CDIP -0.5V to +7.0V -20 mA +20 mA -0.5V to VCC +0.5V -20 mA +20 mA -0.5V to VCC +0.5V
Recommended Operating Conditions
Supply Voltage (VCC) 'AC 'ACT Input Voltage (VI) Output Voltage (VO) Operating Temperature (TA) 54AC/ACT Minimum Input Edge Rate (V/t) 'AC Devices VIN from 30% to 70% of VCC VCC @ 3.3V, 4.5V, 5.5V Minimum Input Edge Rate (V/t) 'ACT Devices VIN from 0.8V to 2.0V VCC @ 4.5V, 5.5V 2.0V to 6.0V 4.5V to 5.5V 0V to VCC 0V to VCC -55°C to +125°C
125 mV/ns
± 50 mA ± 50 mA -65°C to +150°C
175°C
125 mV/ns
Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. National does not recommend operation of FACTTM circuits outside databook specifications.
DC Characteristics for 'AC Family Devices
Symbol Parameter VCC (V) 54AC TA = -55°C to +125°C Guaranteed Limits VIH Minimum High Level Input Voltage VIL Maximum Low Level Input Voltage VOH Minimum High Level Output Voltage 3.0 4.5 5.5 3.0 4.5 5.5 3.0 4.5 5.5 2.1 3.15 3.85 0.9 1.35 1.65 2.9 4.4 5.4 (Note 2) VIN = VIL or VIH 3.0 4.5 5.5 VOL Maximum Low Level Output Voltage 3.0 4.5 5.5 2.4 3.7 4.7 0.1 0.1 0.1 (Note 2) VIN = VIL or VIH 3.0 4.5 5.5 IIN Maximum Input Leakage Current 5.5 0.50 0.50 0.50 V µA IOL 12 mA 24 mA 24 mA VI = VCC, GND V V IOH -12 mA -24 mA -24 mA IOUT = 50 µA V IOUT = -50 µA V VOUT = 0.1V or VCC - 0.1V V VOUT = 0.1V or VCC - 0.1V Units Conditions
± 1.0
3
www.national.com
DC Characteristics for 'AC Family Devices
Symbol Parameter VCC (V)
(Continued)
54AC TA = -55°C to +125°C Guaranteed Limits
Units
Conditions
IOZ
Maximum TRI-STATE Leakage Current 5.5 5.5 5.5 5.5
± 10.0
50 -50 80.0
µA mA mA µA
VI (OE) = VIL, VIH VI = VCC, GND VO = VCC, GND VOLD = 1.65V Max VOHD = 3.85V Min VIN = VCC or GND
IOLD IOHD ICC
(Note 3) Minimum Dynamic Output Current Maximum Quiescent Supply Current
Note 2: All outputs loaded; thresholds on input associated with output under test. Note 3: Maximum test duration 2.0 ms, one output loaded at a time. Note 4: IIN and ICC @ 3.0V are guaranteed to be less than or equal to the respective limit @ 5.5V VCC. Note 5: ICC for 54AC @ 25°C is identical to 74AC @ 25°C.
DC Characteristics for 'ACT Family Devices
Symbol Parameter VCC (V) 54ACT TA = -55°C to +125°C Guaranteed Limits VIH Minimum High Level Input Voltage Maximum Low Level Input Voltage Minimum High Level Output Voltage 4.5 5.5 4.5 5.5 4.5 5.5 2.0 2.0 0.8 0.8 4.4 5.4 (Note 6) VIN = VIL or VIH 4.5 5.5 VOL Maximum Low Level Output Voltage 4.5 5.5 3.70 4.70 0.1 0.1 (Note 6) VIN = VIL or VIH 4.5 5.5 IIN IOZ ICCT IOLD IOHD Maximum Input Leakage Current Maximum TRI-STATE Leakage Current Maximum ICC/Input (Note 7) Minimum Dynamic Output Current 5.5 5.5 50 -50 mA mA VOLD = 1.65V Max VOHD = 3.85V Min 5.5 1.6 mA 5.5 5.5 0.50 0.50 V µA µA IOL 24 mA 24 mA VI = VCC, GND VI = VIL, VIH VO = VCC, GND VI = VCC - 2.1V V V IOH -24 mA -24 mA IOUT = 50 µA V V V VOUT = 0.1V or VCC - 0.1V VOUT = 0.1V or VCC - 0.1V IOUT = -50 µA Units Conditions
VIL
VOH
± 1.0 ± 10.0
www.national.com
4
DC Characteristics for 'ACT Family Devices
Symbol Parameter VCC (V)
(Continued)
54ACT TA = -55°C to +125°C Guaranteed Limits
Units
Conditions
ICC
Maximum Quiescent Supply Current
5.5
80.0
µA
VIN = VCC or GND
Note 6: All outputs loaded; thresholds on input associated with output under test. Note 7: Maximum test duration 2.0 ms, one output loaded at a time. Note 8: ICC for 54ACT @ 25°C is identical to 74ACT @ 25°C.
AC Electrical Characteristics
Symbol Parameter VCC (V) (Note 9) tPLH tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ Propagation Delay In to Zn Propagation Delay In to Zn Propagation Delay S to Zn Propagation Delay S to Zn Output Enable Time Output Enable Time Output Disable Time Output Disable Time 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0
Note 9: Voltage Range 3.3 is 3.0V ± 0.3V Voltage Range 5.0 is 5.0V ± 0.5V
54AC TA = -55°C to +125°C CL = 50 pF 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 11.0 8.0 11.0 8.5 14.5 11.0 14.5 11.0 13.0 10.0 11.0 9.5 13.0 11.0 10.5 9.5
Units
ns ns ns ns ns ns ns ns
AC Electrical Characteristics
Symbol Parameter VCC (V) (Note 10) tPLH tPHL tPLH tPHL tPZH Propagation Delay In to Zn Propagation Delay In to Zn Propagation Delay S to Zn Propagation Delay S to Zn Output Enable Time 5.0 1.0 9.5 ns 5.0 1.0 11.5 ns 5.0 1.0 11.0 ns 5.0 1.0 9.5 ns 5.0 1.0 54ACT TA = -55°C to +125°C CL = 50 pF 8.0 ns Units
5
www.national.com
|
|
