Details, datasheet, quote on part number: NJM2747
PartNJM2747
CategoryAnalog & Mixed-Signal Processing => Amplifiers => Operational Amplifiers => General Purpose => Quad
DescriptionSingle Supply Quad Operational Amplifier with Full Swing Output
The NJM2747 is a quad low supply voltage operational amplifier
with Full swing output.
It is suitable for audio section of portable sets, PCs and any
General-purpose use.
■ FEATURES
●Operating Voltage :2.5V to 14V
●Output Full Swing : VOH ≥4.9V Typ. (at V+=5V, RL=5kΩ)
: VOL ≤0.1V Typ. (at V+=5V, RL=5kΩ)
●Offset Voltage :1mV Typ
●Slew Rate : 3.5V/µs Typ.
. ●Low Distortion : 0.001% typ. (at V+=5V, f=1kHz)
. ●Low Input Voltage Noise :10nV/√Hz typ.
●Bipolar Technology
●Package Outline : DIP14, DMP14, SSOP14
CompanyNJR Corporation
DatasheetDownload NJM2747 datasheet
Quote
Find where to buy
 
  

 

Features, Applications
Single Supply Quad Operational Amplifier with Full Swing Output

GENERAL DESCRIPTION The is a quad low supply voltage operational amplifier with Full swing output. It is suitable for audio section of portable sets, PCs and any General-purpose use. FEATURES Operating Voltage Output Full Swing Offset Voltage Slew Rate. Low Distortion. Low Input Voltage Noise Bipolar Technology Package Outline PIN CONFIGURATION PACKAGE OUTLINE

PIN FUNCTION 1. A OUTPUT 2. A -INPUT 3. A +INPUT 5. B +INPUT 6. B ­INPUT 7. B OUTPUT
8. C OUTPUT 9. C -INPUT 10. A +INPUT 11. GND 12. D +INPUT 13. D ­INPUT 14. D OUTPUT

PARAMETER Supply Voltage Differential Input Voltage Range Common Mode Input Voltage Range Power Dissipation Operating Temperature Range Storage Temperature Range SYMBOL V VID VICM

(Note1) For supply voltage less than 15V, the absolute maximum input voltage is equal to the supply voltage. (Note2) On the PCB " EIA/JEDEC (76.2×114.3×1.6mm, two layers, (Note3) On the PCB " EIA/JEDEC (76.2×114.3×1.6mm, four layers, FR-4) "

PARAMETER Operating Current Input Offset Voltage Input Bias Current Input Offset Current Large Signal Voltage Gain Common Mode Rejection Ratio Supply Voltage Rejection Ratio Output Voltage Input Common Mode Voltage Range SYMBOL I CC VIO IB IIO AV CMR SVR VOH VOL VICM TEST CONDITION =2.5V, No Signal Apply S 10k MIN. TYP. MAX. UNIT dB V

PARAMETER Unity Gain Bandwidth Phase Margin Equivalent Input Noise Voltage Total Harmonic Distortion Amp to Amp Separation SYMBOL V NI THD CS TEST CONDITION 2.5V, Vo=1.5Vrms MIN. TYP. MAX. UNIT MHz Deg nV/ % dB

PARAMETER Slew Rate SYMBOL SR TEST CONDITION (Note to 2.5V MIN. TYP. 3.5 MAX. UNIT V/µs
(Note 4) Number specified is the slower of the positive and negative slew rates.

[CAUTION] The specifications on this data book are only given for information, without any guarantee as regards either mistakes or omissions. The application circuits in this data book are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights.


 

Related products with the same datasheet
NJM2747D
NJM2747M
NJM2747V
Some Part number from the same manufacture NJR Corporation
NJM2747D Single Supply Quad Operational Amplifier with Full Swing OutputThe NJM2747 is a quad low supply voltage operational amplifierwith Full swing output.It is suitable for audio section of portable sets,
NJM2741 Single Supply Single Operational Amplifier with Full Swing OutputThe NJM2741 is a low supply voltage operational amplifier with Fullswing output.It is suitable for audio section of portable sets,
NJU26110 SRS CS II 5.1 & TruSurround XT DecoderThe NJU26110 is a digital signal processor that provides the function of CircleSurround II 5.1 / TruSurroundXT and Mono-to-Stereo.The NJU26110 processes the stereo
NJM2644 Two-phase Unipolar DC Brushless Motor Pre-Driver ICThe NJM2644 is a 2-phase DC brushless motor pre-driver IC.It incorporates Lock Detect and Auto Protection circuit for safetyoperation. Especially,
NJM2734 Full-Swing Input and Output type Quad Operational AmplifierNJM2734 is single supply quad operational amplifier with full swinginput and output, operates from 1.8V.Input and Output Full Swing provides
NJW1156A Two channel electronic volume with 5 input selector.NJW1156A is a two channel electronic volume with 5input selector. It’s suitable for Input signal trimmer ofaudio equipments such as DVD / HDD recorder
NJM2567 Low Voltage Video Amplifier with Y/C MIX and Filter NJM2567 is a low voltage operating video amplifier included LPF,BPFIn Y and C system.Output with 75ohm driver optimize the TV monitor system.The
NJU7747 Low dropout voltage regulator with ON/OFF controlNJU7747/48 is a low dropout voltage regulator with ON/OFFcontrol.Advanced CMOS technology achieves ultra low quiescent current.SC-82AB package and 0.1µF
NJU7751 Low dropout voltage regulator with ON/OFF control and Output shunt switch.NJU7751/54 is a low dropout voltage regulator withON/OFF control and Output shunt switch.Advanced CMOS technology achieves
NJM2845 low dropout voltage regulator. Advanced Bipolar technology achieves low noise, high ripple rejection and low quiescent current.The NJM2845 is low dropout voltage regulator. AdvancedBipolar technology
NJU7380 Stepper Motor ControllerNJU7380 is a controller with transrator which convertfrom input step and direction pulse to driver's phase signalfor full and half step.NJU7380 translates from pulse input
NJM2626 PWM Type 3-Phase DC Brushless Motor ControlThe NJM2626 is a 3-phase DC brush less motor controlpre-driver IC with PWM control.It takes hall IC inputs and generates motor drivingwaveform.Output
NJU26902 Digital Audio DelayThe NJU26902 is a digital audio delay. The NJU26902 provides delay-timeadjustment function and digital audio interface.! FEATURES• 2-Channel Audio Delay (24 bits data width).Delay
NJU7757 Low dropout voltage regulator with ON/OFF control.NJU7757/58 is a low dropout voltage regulator with ON/OFFcontrol.Advanced CMOS technology achieves low quiescent current.SC-82AB package and 0.1uF
NJU7044 Input/Output Full-Swing High Output Current Quad C-MOS Operational AmplifierThe NJU7044 is a quad C-MOS operational amplifier permitting afull-swing input and output in full-swing under high load.Based
NJW4100 Lithium-ion Battery Charger Controller ICThe NJW4100 is a Lithium-ion Battery Charger ControllerIC with over charger timer.Charger current and voltage can individually be set by theexternal resistors.
NJU7630 PWM control Step-Down Switching regulator ICNJU7630 is a high speed low voltage operation switchingregulator control IC. It features a totem pole driver that can directlydrive an external MOS-FET.Internal
NJM2527 Color TFT Signal ProcessorThe NJM2527 is a color TFT signal processor.It contains all function, like as Y/C separator circuit, color signalde-modulator, synchronous separate circuit, RGB interface,
NJW1142A Audio processorThe NJW1142A is a sound processor includes all of thefunctions required to process the audio signal for TV, suchas tone control, balance, volume, mute, and AGC functions.Also the NJW1142A
NJW1146A Audio Processor with BBENJW1146A is an audio processor with BBE, which also includes Mastervolume, Balance, Tone Control, eala(NJRC surround), Mute, and Outputfilter amplifier. All of internal status
NJW1149A Audio Processor with Sound Enhancement and TruSurround 5.1ch VirtualizerThe NJW1149A is an audio processor with BBE sound enhancementand SRS Labs' TruSurround 5.1 channel virtualizer. It includes all offunctions

NJL72H000A : remote control receiver Infrared Remote Control Receiver

NJL72H400A : remote control receiver Infrared Remote Control Receiver

NJM2285 : 2-Input 3 Channel Video Switch

NJM2533 : 2-Input 1-Output Video Switch

NJU6319AE : Quartz Crystal Oscillator Quartz Crystal Oscillator

NJU6425 : LCD Controller Drivers 10-character 3-line Dot Matrix LCD Controller Driver

NJU7701F28 : Voltage Detector

NJG1144KA1 : GPS LOW NOISE AMPLIFIER GaAs MMIC The NJG1144KA1 is a low noise amplifier GaAs MMIC designed for GPS, GALILEO, and GLONASS. This amplifier achieves high gain and a good balance between ultra-low noise figure and excellent VSWR, while low current consumption and high IP3, respectively.The NJG1144KA1

NJW4800 : 30V/4A Half Bridge Driver The NJW4800 is a general purpose, half bridge power driver capable of supplying 4A current. The internal gate driver drives high-side/low-side power MOSFET; therefore, it has fast switching.Additionally, it has protection features such as over current protection and therma

NJM2800F3342-TE1 : Pmic - Voltage Regulator - Linear Integrated Circuit (ics); IC LDO REG W/RESET 3.3V MTP5 Specifications: Lead Free Status: Contains Lead ; RoHS Status: RoHS Non-Compliant

Same catergory

AD737 : RMS-to-DC-Converter. Low Power, Precision, Monolithic True Rms-to-dc Converter With 200 MV Full-scale Input Range.

ADG711 : 2.5 Ohm, Low Voltage, Ultra-low Leakage, Quad SPST (4NC) Switch in Tssop.

CHA5296 : 27-30ghz High Power Amplifier. The is a high gain three-stage monolithic high power amplifier. It is designed for a wide range of applications, from military to commercial communication systems. The backside of the chip is both RF and DC grounds. This helps simplify the assembly process. The circuit is manufactured with a PM-HEMT process on 50µm substrate thickness, 0.25µm gate length,.

GMRS4 : Giant Magneto Resistive Position Sens. This angle sensor is based on the brand new Giant Magneto Resistive (GMR) technology. It is outstanding for the huge tolerances it offers to the user in assembly. GMR sensor on copper leadframe Sensitive to the direction, not to the intensity of the magnetic field Constant TC of basic resistance R and magneto resistance R Applications Rotation sensing.

LC74763 : On-screen Display Lsi. The LC74763 and LC74763M are on-screen display CMOS LSIs that superimpose text and low-level graphics onto a TV screen (video signal) under the control of a microcontroller. The display characters have by 18 dots structure, and 128 characters are provided. Display structure: 12 lines by 24 characters (up to 288 characters) Maximum character display:.

LC89602 : Audio Decoder Lsi For Mini-disk Playback. The is an audio decoder LSI for mini-disk playback units. This LSI implements the processing that precedes the D/A converter in playback-only mini-disk players. That is, the LC89602 receives data in sound frame units from a mini-disk data decoder LSI (such as the Sanyo LC89610), expands the audio signal and decoder that signal directly to a D/A converter.

MAX4322 : Single/Dual/Quad, Low-Cost, SOT23, Low-Power, Rail-to-rail I/o op Amps.

MAX975 : Single/Dual, +3V/+5V Dual-speed Comparators With Auto Standby. The MAX975/MAX977 single/dual comparators feature three different operating modes, and are optimized for +3V and +5V single-supply applications. The operating modes are as follows: high speed, high speed with auto-standby, and low power. Propagation delay 28ns in high-speed mode, while supply current is only 250µA. Supply current is reduced 3µA in low-power.

TA75W393FU : Dual Voltage Comparator.

TL3116CD : ti TL3116, Ultra-fast Low-power Precision Comparator. Ultra-Fast Operation. 10 ns (typ) Low Positive Supply Current 12.7 mA (Typ) Operates From a Single 5-V Supply or From a Split ± 5-V Supply Complementary Outputs Input Common-Mode Voltage Includes Negative Rail Low Offset Voltage No Minimum Slew Rate Requirement Output Latch Capability Functional Replacement to the LT1116 The is an ultra-fast comparator.

TLV2780AID : ti TLV2780A, Single 1.8V Rrio, 8MHz Amplifier With Shutdown. TLV2785, TLV278xA FAMILY 1.8 V HIGH-SPEED RAIL-TO-RAIL INPUT/OUTPUT OPERATIONAL AMPLIFIERS WITH SHUTDOWN The TLV278x single supply operational amplifiers ­60 ­20 provide rail-to-rail input and output capability. The ­90 TLV278x takes the minimum operating supply 10 M voltage down 1.8 V over the extended industrial f ­ Frequency ­ Hz temperature range.

XC221A1100 : Rail- to -rail op Amp. NOperating Voltage Range (Single Cell) ~ 10V NInput / Output Rail To Rail Operation NGain Bandwidth NSlew Rate / µS GPalmtop computers, PDAs GCellular and portable phones GPortable audio systems GVarious battery powered systems NLow Power Consumption : 100µA NSOT - 25 Ultra Small Package The is an input / output rail to rail CMOS Op Amp. With rail to rail.

LTC6103 : Dual High Voltage, High Side Current Sense Amplifier The LTC6103 is a versatile, high voltage, high side, dual current sense amplifier. The two internal amplifiers are independent except that they share the same V– terminal. Design flexibility is provided by the excellent device characteristics: 450µV maximum offset, and only 275µA of current consumption.

ADL5562 : 3.3 GHz Ultralow Distortion RF/IF Differential Amplifier The ADL5562 is a high performance differential amplifier optimized for RF and IF applications. The amplifier offers low noise of 2.1 nV/?Hz and excellent distortion performance over a wide frequency range, making it an ideal driver for high speed 8-bit to 16-bit ADCs. The ADL5562 provides three.

PI3A223 : Dual SPDT With 0.6-Ohm Ron Dual SPDT with 0.6-Ohm Ron.

TPS22932B : Low-Input Voltage, Ultra Low On Resistance Load Switch With Configurable Enable Logic And Controlled TPS22932B is a low rON load switch with controlled turn on. It contains an ultra-low rON P-channel MOSFET that can operate over an input voltage range of 1.1 V to 3.6 V. The switch is controlled by eight patterns of 3-bit input. The user can choose the logic.

 
0-C     D-L     M-R     S-Z