|
Details, datasheet, quote on part number:NTE999SM
| |
Datasheet text preview:
NTE999SM Integrared Circuit Programmable Precision Reference
Description: The NTE999SM integrated circuit is a threeterminal programmable shunt regulator. This monolithic IC voltage reference operates as a low temperature coefficient zener which is programmable from Vref to 36 volts with two external resistors. This device exhibits a wide operating current range of 1.0 to 100mA with a typical dynamic impedance of 0.22. The characteristics of this reference make it an excellent replacement for zener diodes in many applications such as digital voltmeters, power supplies, and op amp circuitry. The 2.5 volt reference makes it convenient to obtain a stable reference from 5.0 volt logic supplies, and since the NTE999SM operates as a shunt regulator, it can be used as either a positive or negative voltage reference. Features: D Programmable Output Voltage to 36 Volts D Voltage Reference Tolerance: ±1.0% D Low Dynamic Output Impedance: 0.22 Typical D Sink Current Capability of 1.0 to 100mA D Equivalent Full Range Temperature Coefficient of 50ppm/°C Typical D Temperature Compensated for Operation over Full Rated Operating Temperature Range D Low Output Noise Voltage. Absolute Maximum Ratings: (TA = 0° to +70°C, unless otherwise noted.) Cathode to Anode Voltage, VKA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37V Cathode Current Range, Continuous, IK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 to +150mA Reference Input Current Range, Continuous, Iref . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.05 to +10mA Total Power Dissipation (TA = +25°C), PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 725mW Derate Above 25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.8mW/°C Operating Junction Temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C Operating Ambient Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0° to +70°C Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65° to +150°C Thermal Resistance, JunctiontoAmbient, RthJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178°C/W Thermal Resistance, JunctiontoCase, RthJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W Lead Temperature (During Soldering, 1/16" ifrom case for 10sec), TL . . . . . . . . . . . . . . . . . . +260°C
Recommended Operating Conditions Cathode to Anode Voltage, VKA Cathode Current, IK Electrical Characteristics (TA = +25°C unless otherwise noted) Characteristic Reference Input Voltage VKA = Vref, IK = 10mA TA = +25°C Reference Input Voltage Deviation Over Temperature Range (Note 1, 2) VKA = Vref, IK = 10mA Ratio of Change in Reference Input Voltage to Change in Cathode to Anode Voltage IK = 10mA, VKA = 10V to Vref VKA = 36V to 10V Reference Input Current IK = 10mA, R1 = 10k, R2 = TA = +25°C TA = Tlow to Thigh (Note 1) Reference Input Current Deviation Over Temperature Range (Note 1) IK = 10mA, R1 = 10k, R2 = Minimum Cathode Current for Regulation VKA = Vref OffState Cathode Current VKA = 36V, Vref = 0V Dynamic Impedance (Note 3) VKA = Vref, IK = 1.0mA to 100mA f 1.0kHz Note 1: Tlow = 0°C, Thigh = +70°C Symbol Vref Vref Vref VKA I ref I ref I min Ioff |Zka| 1.8 1.8 0.5 2.6 Min 2.470 Typ
Min Vref 1.0
Max 36 100
Unit V mA
Max 2.520
Unit V
2.495
3.0
17
mV mV/V
1.4 1.0
2.7 2.0 µA 4.0 5.2 4.0 1.0 1000 0.5 µA mA nA
0.22
Note 2: The deviation parameter Vref is defined as the differences between the maximum and minimum values obtained over the full operating ambient temperature range that applies. Vref = VrefMax VrefMin TA = T2T1 Note 2: (cont'd) The average temperature coefficient of the reference input voltage, Vref, is defined as: Vref Vref ppm Vref @ 25°C x 106 Vref x 106
= = ° TA (Vref @ 25°C) TA C Vref can be positive or negative depending on whether Vref Min or Vref Max occurs at the lower ambient temperature.
Note 3: The dynamic impedance Zka is defined as: |Zka| =
VKA IK When the device is programmed with two external resistors, R1 and R2, the total dynamic impedance of the circuit is defined as: |Zka'| |Zka| 1+ R1 R2
Pin Connection Diagram
Cathode Anode Anode N.C.
1 2 3 4
8 7 6 5
Reference Anode Anode N.C.
.192 (4.9)
8
5
.236 (5.99) .154 (3.91)
1
4
.050 (1.27)
016 (.406) 061 (1.53)
.198 (5.03)
.006 (.152)
NOTE: Pin1 on Beveled Edge
|
|
