Details, datasheet, quote on part number: MC33762DM-2525R2
PartMC33762DM-2525R2
CategoryPower Management => Regulators => Linear Voltage Regulators => LDO (Low Drop Out)
DescriptionIndependent Dual Channel 80mA, 2.5V Output, Low Dropout Voltage Regulator With Enable And Ultra Low Noise, Package: Micro-8, Pins=8
CompanyON Semiconductor
DatasheetDownload MC33762DM-2525R2 datasheet
Quote
Find where to buy
 
  

 

Features, Applications
MC33762 Dual Ultra Low-Noise Low Dropout Voltage Regulator with 1.0 V ON/OFF Control

The is a dual Low DropOut (LDO) regulator featuring excellent noise performances. Thanks to its innovative design, the circuit reaches an impressive 40 VRMS noise level without an external bypass capacitor. Housed in a small 8 package, it represents the ideal designer's choice when space and noise are at premium. The absence of external bandgap capacitor accelerates the response time to a wake-up signal and keeps it within 40 s, making the as a natural candidate for portable applications. The MC33762 also hosts a novel architecture which prevents excessive undershoots in the presence of fast transient bursts, as in any bursting systems. Finally, with a static line regulation better than -75 dB, it naturally shields the downstream electronics from choppy lines.

Nominal Output Current 80 mA with 100 mA Peak Capability Ultra-Low Noise: 150 nV/Hz @ 100 Hz, 40 VRMS

100 Hz-100 kHz Typical, Iout = 60 mA, 1.0 F Fast Response Time from OFF to ON: 40 s Typical Ready for 1.0 V Platforms: ON with 900 mV High Level Typical Dropout @ 30 mA, 80 mA Ripple Rejection: @ 1.0 kHz 1.5% Output Precision @ 25C Thermal Shutdown Vout Available 2.8 V, and 3.0 V Separate Dice for Each Regulator Provides Maximum Isolation Between Regulators Operating Range from to +85C

Gnd1 1 xxxx YWW En2 4 (Top View) xxxx = Version Y = Year WW = Work Week
Applications

See detailed ordering and shipping information in the package dimensions section on page 14 of this data sheet.

Noise Sensitive Circuits: VCOs RF Stages, etc. Bursting Systems (TDMA Phones) All Battery Operated Devices

8 *Current Limit *Antisaturation Protection *Load Transient Improvement
6 *Current Limit *Antisaturation Protection *Load Transient Improvement

Pin Name Vcc1 Vout1 Function Ground of the 1st LDO Enables the 1st LDO Ground of the 2nd LDO Enables the 2nd LDO 2nd LDO Vcc pin Shuts or wakes-up the IC 1st LDO Vcc pin Delivers the output voltage 900 mV level on this pin is sufficient to start this LDO. 150 mV shuts it down. This pin brings the power to the 1st LDO and requires adequate decoupling. This pin requires 1.0 F output capacitor to be stable. This pin brings the power to the 1st LDO and requires adequate decoupling. This pin requires 1.0 F output capacitor to be stable. 900 mV level on this pin is sufficient to start this LDO. 150 mV shuts it down. Description

Value Rating Power Supply Voltage ESD Capability, HBM Model ESD Capability, Machine Model Maximum Power Dissipation NW Suffix, Plastic Package Thermal Resistance Junction-to-Air Operating Ambient Temperature Maximum Junction Temperature (Note 1) Maximum Operating Junction Temperature (Note 2) Storage Temperature Range 1. Internally limited by shutdown. 2. Specifications are guaranteed below this value. Pin # 1 All Pins All Pins Symbol Vin - PD RqJ-A TA TJmax TJ Tstg Min Max 1.0 200 Internally Limited to +150 Unit V W C/W C

(For typical values = 25C, for min/max values to +85C, max = 125C unless otherwise noted) Characteristics Pin # Symbol Min Typ Max Unit

Input Voltage Range ON/OFF Input Resistance (all versions) ON/OFF Control Voltages (Note 3) Logic Zero, OFF State, 50 mA Logic One, ON State, mA 2-4 VON/OFF RON/OFF VON/OFF Vin kW mV

Current Consumption in OFF State (all versions) OFF Mode Current: Vin = Vout = 0, VOFF 150 mV Current Consumption in ON State (all versions) ON Mode Current: Vin = Vout = 0, VON 3.5 V Current Consumption in ON State (all versions), ON Mode Saturation Current: Vin = Vout V, No Output Load Current Limit Vin = Voutnom 1.0 V, Output is brought to Voutnom 0.3 V (all versions) IQOFF IQON IQSAT IMAX mA

Line Regulation (all versions) Vout V < Vin 12 V, Iout 80 mA Load Regulation (all versions) Vin = Vout 1.0 V, Cout = 1.0 mF, Iout 80 mA Dropout Voltage (all versions) (Note 3) Iout 30 mA Iout 60 mA Iout mA 3. Voltage slope should be greater than 2.0 mV/ms 5-7 Regline Regload mV 5-7 Vin-Vout


 

Related products with the same datasheet
MC33762DM-2828R2
MC33762DM-3030R2
MC33762DM-2828RG
MC33762DM-2828RG
MC33762DM-3030RG
MC33762DM-3030RG
Some Part number from the same manufacture ON Semiconductor
MC33762DM-2828R2 Independent Dual Channel 80mA, 2.5V Output, Low Dropout Voltage Regulator With Enable And Ultra Low Noise, Package: Micro-8, Pins=8
MC33765 Very Low Dropout, Ultra Low Noise, 5 Outputs Voltage Regulator
MC33765DTB Very Low Dropout, Ultra Low Noise, 5 Outputs Voltage Regulator, Package: Tssop, Pins=16
MC34001 JFET Input op Amp
MC34001B
MC34002 JFET Input Operational Amplifier
MC34023 High Speed Single-ended PWM Controller
MC34023P Hi-spd PWM Controller , Package: Soic, Pins=16
MC34025 High Speed Double-ended PWM Controller
MC34025DW Hi-spd PWM Controller , Package: Soic, Pins=16
MC34025DWR2 Up-to-1MHz Dual Output (Push-pull or H-Bridge) Voltage-or-current-mode PWM Controller, Package: Soic, Pins=16
MC34025P Hi-spd PWM Controller , Package: Soic, Pins=16
MC3403 Quad Low Power Operational Amplifier
MC3403D 3-36V Quad Channel Operational Amplifier, ta = -40 to +85°C, Package: Soic, Pins=14
MC3403P Single Supply Quad Operational Amplifier , Package: Pdip, Pins=14
MC3405 Dual Operational Amplifier And Dual Comparator
MC34060A Precision Switchmode Pulse Width Modulator Control Circuit
MC34060AD Up-to-200kHz Multi-topology PWM Voltage-mode Controller, Package: Soic, Pins=14
MC34060AP Fixed Frequency, Pwm, Voltage Mode Single Ended Controller , Package: Pdip, Pins=14
MC34063A Dc-to-dc Converter Control Circuit
MC34063AD Up-to-100kHz Multi-topology Burst-mode Voltage-mode Controller With 40V / 1.5A Switch, Package: Soic, Pins=8
Same catergory

BP5061-5 : . Parameter Input voltage Output current ESD endurance Operating temperature range Storage temperature range Symbol Vi Io Vsurge Topr Tstg Limits Unit V mApk kV C Symbol Min. Parameter Input voltage range -113 Vi Output voltage -4.7 Vo Output current 0 Io Line regulation - Vr Load regulation - Vl Output ripple voltage - Vp Power conversion effciency.

FAN8082 : DC Motor Drivers. DC Motor Driver. Built-in brake function for stable brake characteristics. Built-in element to absorb a surge current derived from changing motor direction and braking motor drive. Motor speed control by an external voltage. Stable motor direction change. Interfaces with CMOS devices. Built-in the thermal shut down circuit (165C). Low standby current. (6.5mA) The is a monolithic.

ICE1PD265G : Power Factor Controller + Cool- MOS: Boostset ic For High Power Factor And Low THD.

ISL6536A : Four Channel Supervisory ic The ISL6536A is a Four Channel Supervisory ic Designed to Monitor Voltages >, = 0.7V. This ic Bias Range is From 2.7V to 5V But CAN Supervise Any Positive Voltage Using an External Resistor Divider to Translate to a Lower Voltage For Comparison to The Internal 0.63V Reference..

LM336-2.5 : 2.5-v Integrated Reference Circuits. Low Temperature Coefficient Wide Operating Current. mA 0.27- Dynamic Impedance 1% Tolerance Available Specified Temperature Stability Easily Trimmed for Minimum Temperature Drift Fast Turnon Three-Lead Transistor Package NC-No internal connection LP PACKAGE (TOP VIEW) ANODE CATHODE ADJ The LM236-2.5, LM336-2.5, and LM336B-2.5 integrated circuits are precision.

LTC3412 : Step-Down. LTC3412, 4MHz, 2.5A Synchronous Step-down DC/DC Converter. High Efficiency: 95% 2.5A Output Current Low Quiescent Current: 62A Low RDS(ON) Internal Switches: 85m Programmable Frequency: 4MHz No Schottky Diode Required 2% Output Voltage Accuracy 0.8V Reference Allows Low Output Voltage Selectable Forced Continuous/Burst Mode Operation with Adjustable Burst Clamp Synchronizable Switching Frequency Low Dropout.

LX1722-6CHEVALKIT : AudioMAX Products. Audiomax Products, Package : (none). AUDIOMAX 5.1 CHANNEL DVD CLASS-D AMPLIFIER EVALUATION BOARD USER'S GUIDE Board Settings. 3 System s. 4 Schematic 5 Bill of Materials. 9 Audio Measurements. 10 Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 The LXE1722 6-CH Evaluation Board is a fully functional 5.1 channel class-D.

MAX687 : -. o Fixed Outputs: (MAX689) o Directly Drives External PNP Transistor o 10mA Min Base-Current Drive for >1A Output o Low Dropout Voltage: 100mV Dropout at 650mA Output (FZT749) 40mV Dropout at 200mA Output (FZT749) 0.8V Dropout at 4A Output o Power-Fail Output Monitors the Output Voltage o Automatic, Latched Shutdown when Output Falls Out of Regulation.

MC78T05 : 3-Terminal 3A Positive Voltage Regulator. Output Current in Excess of 3.0A Output Transistor Safe Operating Area Compensation Power Dissipation :25W Internal Short Circuit Current Limiting Internal Thermal Overload Protection Output Voltage Offered in 4% Tolerance No External Components Required Output Voltage of 5,12 and 15V This family of fixed voltage regulators are monolithic integrated.

PST37 : System Reset. CMOS System Reset. This CMOS output type system reset IC, developed using the CMOS. Super low consumption current of 1.0A typ. ~ PST3719) has been achieved through use of the CMOS process. Also, detection voltage is high precision detection of 2%. (1) Super low consumption current (2) High precision detection voltage (3) Operating range (4) Wide operating temperature.

REG101-33 : . q NEW DMOS TOPOLOGY: Ultra Low Dropout Voltage: 60mV typ at 100mA Output capacitor NOT required for stability q FAST TRANSIENT RESPONSE q VERY LOW NOISE: 23Vrms q HIGH ACCURACY: 1.5% max q HIGH EFFICIENCY: IGND 500A at IOUT = 100mA Not Enabled: IGND 3.3V, 5.0V, AND ADJUSTABLE OUTPUT VERSIONS q OTHER OUTPUT VOLTAGES AVAILABLE UPON REQUEST q FOLDBACK.

TPS2024D : Hot-Swap Switches, Integrated FET. ti TPS2024, 2.2A, 2.7-5.5V Single Hot-swap ic Hi-side MOSFET, Fault Report, Act-low Enable.

TPS3128E15DBVR : ti TPS3128E15, 1.5-V Processor Supervisory Circuit. typical applications Minimum Supply Voltage 0.75 V Supply Voltage Supervision Range: V (TPS3125 Devices Only) Other Versions on Request Power-On Reset Generator With Fixed Delay Time 180 ms Manual Reset Input (TPS3123/5/6/8) Watchdog Timer Retriggers the RESET Output at VDD VIT Supply Current 14 A (Typ) SOT235 Package Temperature Range. to 85C.

UNR-1.8/2-D5 : DC/DC Power Converters. Low cost! High reliability! x 1" SMT or through-hole packages Gull-wing leads; Standard reflow Complete; No external components Outputs: 2.5V/2A, 3.3V/3A Inputs: 4.75-5.5V, 10.8-13.6V Guaranteed efficiencies to 87% Output noise as low as 40mVp-p Transient response as quick to +70C operation with no derating On/off control; EMC compliant IEC950/EN60950/UL1950.

UPC1060 : 2.5 V High Precision Reference Voltage Circuit. The PC1060 are high accuracy and low drift voltage references 2.5 V output voltage. This IC can operate under wide range input voltage, and applied for to 12 bits D/A converters. High Accuracy Low Temperature Coefficient Low Supply Current Wide Supply Voltage Range Low Load Regulation = 2.5 The information in this document is subject to change without.

FPF2105 : Full Function Load Switches The FPF2100 through FPF2107 is a family of load switches which provide full protection to systems and loads which may encounter large current conditions. These devices contain a 0.125W current-limited P-channel MOSFET which can operate over an input voltage range of 1.8-5.5V. Switch control is by a logic input (ON) capable.

ISL88550A : Synchronous Step Down Controller with Sourcing and Sinking LDO Regulator ISL88550A integrates a synchronous buck PWM controller to generate VDDQ, a sourcing and sinking LDO linear regulator to generate VTT, and a 10mA reference output buffer to generate VTTR. The buck controller drives two external N-Channel MOSFETs to generate output voltages down.

BQ4011LY : 32Kx8 Nonvolatile SRAM, 3.3-V Input, 10% Voltage Tolerance The CMOS bq4011/Y/LY is a nonvolatile 262,144-bit static RAM organized as 32,768 words by 8 bits. The integral control circuitry and lithium energy source provide reliable nonvolatility coupled with the unlimited write cycles of standard SRAM. The control circuitry constantly monitors the single.

FSBF3CH60B : Smart Power Module It is an advanced smart power module (SPM) that Fairchild has newly developed and designed to provide very compact and high performance ac motor drives mainly targeting lowpower inverterdriven application like air conditioner and washing machine. It combines optimized circuit protection and drive matched to lowloss IGBTs. System.

PT7M7342JTA : P Supervisor Circuits The PT7M7xxx family microprocessor (P) supervisory circuits are targeted to improve reliability and accuracy of power-supply circuitry in P systems. These devices reduce the complexity and number of components required to monitor power-supply and battery functions..

 
0-C     D-L     M-R     S-Z