Details, datasheet, quote on part number: MC74HC4316DTR2
PartMC74HC4316DTR2
CategoryAnalog & Mixed-Signal Processing => Switches & Multiplexers => Analog Multiplexers/Demultiplexers
DescriptionQuad Analog Switch/multiplexer/demultiplexer With Separate Analog / Digital Power Supplies
CompanyON Semiconductor
DatasheetDownload MC74HC4316DTR2 datasheet
  

 

Features, Applications

This document, MC74HC4316/D has been canceled and replaced by MC74HC4316A/D LAN was sent 9/28/01
Quad Analog Switch/ Multiplexer/Demultiplexer with Separate Analog and Digital Power Supplies

The MC74HC4316 utilizes silicon­gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF­channel leakage current. This bilateral switch/multiplexer/demultiplexer controls analog and digital voltages that may vary across the full analog power­supply range (from VCC to VEE). The HC4316 is similar in function to the metal­gate CMOS MC14016 and MC14066, and to the High­Speed CMOS HC4016 and HC4066. Each device has four independent switches. The device control and Enable inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. The device has been designed so that the ON resistances (RON) are much more linear over input voltage than RON of metal­gate CMOS analog switches. Logic­level translators are provided so that the On/Off Control and Enable logic­level voltages need only be VCC and GND, while the switch is passing signals ranging between VCC and VEE. When the Enable pin (active­low) is high, all four analog switches are turned off. Logic­Level Translator for On/Off Control and Enable Inputs Fast Switching and Propagation Speeds High ON/OFF Output Voltage Ratio Diode Protection on All Inputs/Outputs Analog Power­Supply Voltage Range (VCC ­ VEE) to 12.0 Volts Digital (Control) Power­Supply Voltage Range (VCC ­ GND) to 6.0 Volts, Independent of VEE Improved Linearity of ON Resistance Chip Complexity: 66 FETs or 16.5 Equivalent Gates LOGIC DIAGRAM

XA A ON/OFF CONTROL 1 15 LEVEL TRANSLATOR ANALOG SWITCH LEVEL TRANSLATOR ANALOG SWITCH LEVEL TRANSLATOR ANALOG SWITCH LEVEL TRANSLATOR ANALOG INPUTS/OUTPUTS = XA, XB, XC, 3 YB ANALOG OUTPUTS/INPUTS PIN 16 = VCC PIN 8 = GND PIN 9 = VEE GND VEE ANALOG SWITCH 2 YA

XB B ON/OFF CONTROL C ON/OFF CONTROL ENABLE GND VCC A ON/OFF CONTROL D ON/OFF CONTROL YC XC VEE
XB B ON/OFF CONTROL XC C ON/OFF CONTROL XD D ON/OFF CONTROL ENABLE

Symbol VCC VEE VIS Vin I Parameter Value Unit Positive DC Supply Voltage (Ref. to GND) (Ref. to VEE) + 0.5 VEE 0.5 to VCC + 0.5 Negative DC Supply Voltage (Ref. to GND) Analog Input Voltage DC Input Voltage (Ref. to GND) 1.5 to VCC DC Current Into or Out of Any Pin Power Dissipation in Still Air Storage Temperature mA PD Plastic DIP SOIC Package mW _C Tstg 150 260 Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP or SOIC Package)

This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high­impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND v (Vin or Vout) v VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. I/O pins must be connected to a properly terminated line or bus.

Symbol VCC VEE VIS Vin Parameter Min 2.0 Max 6.0 Unit Positive DC Supply Voltage (Ref. to GND) Negative DC Supply Voltage (Ref. to GND) Analog Input Voltage ­ 6.0 VEE GND VCC 1.2 Digital Input Voltage (Ref. to GND) GND VIO* TA Static or Dynamic Voltage Across Switch Operating Temperature, All Package Types Input Rise and Fall Time (Control or Enable Inputs) (Figure _C ns tr, tf VCC 2.0 V VCC 4.5 V VCC V * For voltage drops across the switch greater than 1.2 V (switch on), excessive VCC current may be drawn; i.e., the current out of the switch may contain both VCC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.

* Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. Derating Plastic DIP: ­ 10 mW/_C from to 125_C SOIC Package: ­ 7 mW/_C from to 125_C

DC ELECTRICAL CHARACTERISTICS Digital Section (Voltages Referenced to GND) VEE = GND Except Where Noted

Guaranteed Limit v 85_C VCC to 25_C Symbol VIH Parameter Test Conditions v 125_C Unit V Minimum High­Level Voltage, Control or Enable Inputs Ron = Per Spec VIL Maximum Low­Level Voltage, Control or Enable Inputs Maximum Input Leakage Current, Control or Enable Inputs Ron = Per Spec V Iin Vin = VCC or GND VEE 6.0 V Vin = VCC or GND VIO V µA ICC Maximum Quiescent Supply Current (per Package) µA VEE = GND VEE


 

Related products with the same datasheet
MC74HC4316D
MC74HC4316DR2
MC74HC4316DT
MC74HC4316F
MC74HC4316FEL
MC74HC4316FL1
MC74HC4316FL2
MC74HC4316FR1
MC74HC4316FR2
MC74HC4316N
MC74HC4316ND
Some Part number from the same manufacture ON Semiconductor
MC74HC4316F Quad Analog Switch/multiplexer/demultiplexer With Separate Analog / Digital Power Supplies
MC74HC4351
MC74HC4538A Dual Precision Monostable Multivibrator Retriggerable, Resettable)
MC74HC4538AD Multivibrator Prescision Monostable Dua , Package: Soic, Pins=16
MC74HC4538ADTR2 Multivibrator Prescision Monostable Dua, Package: Tssop, Pins=16
MC74HC4538AF Multivibrator Prescision Monostable Dua , Package: Soic, Pins=16
MC74HC4538AFEL Multivibrator Prescision Monostable Dua, Package: Tssop, Pins=16
MC74HC4538AFL1 Multivibrator Prescision Monostable Dua , Package: Soic, Pins=16
MC74HC4538DTEL
MC74HC4851A Analog Multiplexer/demultiplexer With Injection Current Effect Control, Automotive Customi
MC74HC4851AD Analog Multiplexers/demultiplexers With Injection Current Effect Control , Package: Soic, Pins=16
MC74HC4851ADT Analog Multiplexers/demultiplexers With Injection Current Effect Control, Package: Tssop, Pins=16
MC74HC4851ADTR2 Analog Multiplexers/demultiplexers With Injection Current Effect Control , Package: Soic, Pins=16
MC74HC4851ADW Analog Multiplexers/demultiplexers With Injection Current Effect Control, Package: Tssop, Pins=16
MC74HC4851ADWR2 Analog Multiplexers/demultiplexers With Injection Current Effect Control , Package: Soic, Pins=16
MC74HC4851AFR2 Analog Multiplexer/demultiplexer With Injection Current Effect Control, Automotive Customi
MC74HC4851AN Analog Multiplexers/demultiplexers With Injection Current Effect Control, Package: Tssop, Pins=16
MC74HC4852A Analog Multiplexer/demultiplexer With Injection Current Effect Control, Automotive Customi
MC74HC4852AD Analog Multiplexers/demultiplexers With Injection Current Effect Control , Package: Soic, Pins=16
MC74HC4852ADTR2 Analog Multiplexers/demultiplexers With Injection Current Effect Control, Package: Tssop, Pins=16
MC74HC4852ADWR2 Analog Multiplexers/demultiplexers With Injection Current Effect Control

1N4751A : One Watt Hermetically Sealed Glass Silicon Zener Diodes

CS5257A-1GT5 : 7A LDO 5-Pin Adjustable Linear Regulator , Package: D2Pak, Pins=5

MC10H181FNR2 : 4-Bit Arithmetic Logic Unit/function Generator, Package: Plcc, Pins=28

MC74LVX08D : Quad 2-Input Gate , Package: Soic, Pins=14

MPS751RLRA : Small Signal High Current Npn, Package: TO-92 (TO-226), Pins=3

NTD4808NT4G : Power MOSFET 30 V, 88 A, Single N-Channel, DPAK/IPAK

NTD3055-094-1 : 9.0 Amps, 60 Volts, Logic Level, N−channel DPAK

MC3423_05 : Overvoltage Crowbar Sensing Circuit

NCP600MN130R2G : Pmic - Voltage Regulator - Linear (ldo) Integrated Circuit (ics); IC REG LDO 150MA 1.3V 6-DFN Specifications: Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

 
0-C     D-L     M-R     S-Z