|
Details, datasheet, quote on part number:MURS160T3
| |
Datasheet text preview:
MURS120T3 Series
Preferred Devices
Surface Mount Ultrafast Power Rectifiers
MURS105T3, MURS110T3, MURS115T3, MURS120T3, MURS140T3, MURS160T3
http://onsemi.com
Ideally suited for high voltage, high frequency rectification, or as free wheeling and protection diodes in surface mount applications where compact size and weight are critical to the system.
· · · ·
Small Compact Surface Mountable Package with JBend Leads Rectangular Package for Automated Handling High Temperature Glass Passivated Junction Low Forward Voltage Drop (0.71 to 1.05 Volts Max @ 1.0 A, TJ = 150°C)
ULTRAFAST RECTIFIERS 1.0 AMPERE 50600 VOLTS
Mechanical Characteristics:
· Case: Epoxy, Molded · Weight: 95 mg (approximately) · Finish: All External Surfaces Corrosion Resistant and Terminal · · · ·
Leads are Readily Solderable Lead and Mounting Surface Temperature for Soldering Purposes: 260°C Max. for 10 Seconds Shipped in 12 mm Tape and Reel, 2500 units per reel Polarity: Polarity Band Indicates Cathode Lead Marking: U1A, U1B, U1C, U1D, U1G, U1J
SMB CASE 403A
MARKING DIAGRAM
U1x
MAXIMUM RATINGS
Please See the Table on the Following Page
U1x= Device Code x = Specific Device Code = A, B, C, D, G or J
ORDERING INFORMATION
See detailed ordering and shipping information in the table on page 2 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking table on page 2 of this data sheet. Preferred devices are recommended choices for future use and best overall value.
© Semiconductor Components Industries, LLC, 2000
1
October, 2000 Rev. 5
Publication Order Number: MURS120T3/D
MURS120T3 Series
MAXIMUM RATINGS
MURS Rating Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Average Rectified Forward Current NonRepetitive Peak Surge Current (Surge applied at rated load conditions halfwave, single phase, 60 Hz) Operating Junction Temperature Symbol VRRM VRWM VR IF(AV) IFSM 105T3 50 110T3 100 115T3 150 120T3 200 140T3 400 160T3 600 Unit Volts
1.0 @ TL = 155°C 2.0 @ TL = 145°C 40
1.0 @ TL = 150°C 2.0 @ TL = 125°C 35
Amps Amps
TJ
*65 to +175
°C
THERMAL CHARACTERISTICS
Thermal Resistance, Junction to Lead (TL = 25°C) R J L 13 °C/W
ELECTRICAL CHARACTERISTICS
Maximum Instantaneous Forward Voltage (Note 1.) (iF = 1.0 A, TJ = 25°C) (iF = 1.0 A, TJ = 150°C) Maximum Instantaneous Reverse Current (Note 1.) (Rated dc Voltage, TJ = 25°C) (Rated dc Voltage, TJ = 150°C) Maximum Reverse Recovery Time (iF = 1.0 A, di/dt = 50 A/µs) (iF = 0.5 A, iR = 1.0 A, IR to 0.25 A) Maximum Forward Recovery Time (iF = 1.0 A, di/dt = 100 A/µs, Rec. to 1.0 V) 1. Pulse Test: Pulse Width = 300 µs, Duty Cycle v 2.0%. vF 0.875 0.71 iR 2.0 50 trr 35 25 tfr 25 75 50 50 ns 5.0 150 ns 1.25 1.05 µA Volts
DEVICE MARKING AND ORDERING INFORMATION
Device MURS105T3 MURS110T3 MURS115T3 MURS120T3 MURS140T3 MURS160T3 Marking U1A U1B U1C U1D U1G U1J Package SMB SMB SMB SMB SMB SMB Shipping 2500 Units/Tape & Reel 2500 Units/Tape & Reel 2500 Units/Tape & Reel 2500 Units/Tape & Reel 2500 Units/Tape & Reel 2500 Units/Tape & Reel
http://onsemi.com
2
MURS120T3 Series
MURS105T3, MURS110T3, MURS115T3, MURS120T3
10 IR, REVERSE CURRENT (m A) 7.0 5.0 3.0 i , INSTANTANEOUS FORWARD CURRENT (AMPS) F 2.0 TC = 25°C 1.0 0.7 0.5 0.3 0.2 50 45 40 C, CAPACITANCE (pF) 35 30 25 20 15 10 0.01 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 5.0 0 0 10 20 30 40 50 60 70 80 90 100 NOTE: TYPICAL CAPACITANCE AT 0 V = 45 pF 80 40 20 8.0 4.0 2.0 0.8 0.4 0.2 0.08 0.04 0.02 0.008 0.004 0.002 0 20 40 60
TJ = 175°C
TJ = 100°C
175°C
100°C
TJ = 25°C
80
100
120
140
160
180 200
VR, REVERSE VOLTAGE (VOLTS)
Figure 2. Typical Reverse Current*
* The curves shown are typical for the highest voltage device in the voltage grouping. Typical reverse current for lower voltage selections can be estimated from these same curves if applied VR is sufficiently below rated VR.
0.1
0.07 0.05 0.03 0.02
vF, INSTANTANEOUS VOLTAGE (VOLTS)
Figure 1. Typical Forward Voltage
VR, REVERSE VOLTAGE (VOLTS)
Figure 3. Typical Capacitance
PF(AV) , AVERAGE POWER DISSIPATION (WATTS) IF(AV) , AVERAGE FORWARD CURRENT (AMPS) 10 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 80 90 100 110 120 SQUARE WAVE 130 140 150 160 170 180 dc RATED VOLTAGE APPLIED RqJC = 13°C/W TJ = 175°C 5.0 TJ = 175°C 4.0 3.0 2.0 1.0 0 (CAPACITANCE LOAD) PK + 20 I I 10 5.0
AV
dc SQUARE WAVE
0
0.5
1.0
1.5
2.0
2.5
TC, CASE TEMPERATURE (°C)
IF(AV), AVERAGE FORWARD CURRENT (AMPS)
Figure 4. Current Derating, Case
Figure 5. Power Dissipation
http://onsemi.com
3
|
|
