|
Details, datasheet, quote on part number:MZP4753A
| |
Datasheet text preview:
MOTOROLA
SEMICONDUCTOR
TECHNICAL DATA
1 to 3 Watt DO-41 Surmetic 30 Zener Voltage Regulator Diodes
GENERAL DATA APPLICABLE TO ALL SERIES IN THIS GROUP
MZP4728A SERIES
13 WATT DO-41 SURMETIC 30
1 TO 3 WATT ZENER REGULATOR DIODES 3.3400 VOLTS
1 to 3 Watt Surmetic 30 Silicon Zener Diodes
. . . a complete series of 1 to 3 Watt Zener Diodes with limits and operating characteristics that reflect the superior capabilities of silicon-oxide-passivated junctions. All this in an axial-lead, transfer-molded plastic package offering protection in all common environmental conditions. Specification Features: · Surge Rating of 98 Watts @ 1 ms · Maximum Limits Guaranteed On Up To Six Electrical Parameters · Package No Larger Than the Conventional 1 Watt Package Mechanical Characteristics: CASE: Void-free, transfer-molded, thermosetting plastic FINISH: All external surfaces are corrosion resistant and leads are readily solderable POLARITY: Cathode indicated by color band. When operated in zener mode, cathode will be positive with respect to anode MOUNTING POSITION: Any WEIGHT: 0.4 gram (approx) WAFER FAB LOCATION: Phoenix, Arizona ASSEMBLY/TEST LOCATION: Seoul, Korea MAXIMUM RATINGS
Rating DC Power Dissipation @ TL = 75°C Lead Length = 3/8 Derate above 75°C DC Power Dissipation @ TA = 50°C Derate above 50°C Operating and Storage Junction Temperature Range 5 PD, MAXIMUM DISSIPATION (WATTS) L = 1/8 4 L = 3/8 3 L = LEAD LENGTH TO HEAT SINK Symbol PD
CASE 59-03 DO-41 PLASTIC
Value 3 24
Unit Watts mW/°C Watt mW/°C °C
PD TJ, Tstg
1 6.67 65 to +200
2
L = 1
1
0
0
20
40
60 80 100 120 140 160 TL, LEAD TEMPERATURE (°C)
180
200
Figure 1. Power Temperature Derating Curve
Motorola TVS/Zener Device Data
500 mW DO-35 Glass Data Sheet 6-1
GENERAL DATA -- 500 mW DO-35 GLASS
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) VF = 1.5 V Max, lF = 200 mA for all types
Nominal Zener Voltage VZ @ IZT Volts (Note 2) 3.6 6.2 11 15 36 Max Zener Impedance (Note 3) Test Current Current IZT mA 69 41 23 17 7 ZZT @ IZT Ohms 10 2 8 14 50 ZZK @ IZK Ohms 400 700 700 700 1000 IZK mA 1 1 0.25 0.25 0.25 Leakage Current IR @ µA Max 100 10 5 5 5 VR Volts 1 3 8.4 11.4 27.4 Surge Current @ TA = 25°C 25°C ir mA (Note 4) 1260 730 414 304 125
Motorola Type No. (Note 1) MZP4729A MZP4735A MZP4741A MZP4744A MZP4753A
NOTE 1. TOLERANCE AND TYPE NUMBER DESIGNATION The type numbers listed have a standard tolerance on the nominal zener voltage of ±5%. The tolerance on the 1M type numbers is indicated by the digits following ZS in the part number. "5" indicates a ±5% VZ tolerance. NOTE 2. ZENER VOLTAGE (VZ) MEASUREMENT Motorola guarantees the zener voltage when measured at 90 seconds while maintaining the lead temperature (TL) at 30°C ±1°C, 3/8 from the diode body. NOTE 3. ZENER IMPEDANCE (ZZ) DERIVATION The zener impedance is derived from the 60 cycle ac voltage, which results when an ac
current having an rms value equal to 10% of the dc zener current (IZT or IZK) is superimposed on IZT or IZK. NOTE 4. SURGE CURRENT (ir) NON-REPETITIVE The rating listed in the electrical characteristics table is maximum peak, non-repetitive, reverse surge current of 1/2 square wave or equivalent sine wave pulse of 1/120 second duration superimposed on the test current, IZT, however, actual device capability is as described in Figure 3 of General Data -- Surmetic 30. NOTE 5. SPECIAL SELECTIONS AVAILABLE INCLUDE: Nominal zener voltages between those shown. Tight voltage tolerances such as ±1% and ±2%. Consult factory.
500 mW DO-35 Glass Data Sheet 6-2
Motorola TVS/Zener Device Data
GENERAL DATA -- 500 mW DO-35 GLASS
JL (t, D) TRANSIENT THERMAL RESISTANCE JUNCTION-TO-LEAD (°C/W)
30 20 10 7 5 3 2 1 0.7 0.5 D =0.5 0.2 0.1 0.05 0.02 0.01 D=0 0.0005 0.001 0.002 0.005 NOTE: BELOW 0.1 SECOND, THERMAL RESPONSE CURVE IS APPLICABLE TO ANY LEAD LENGTH (L). 0.01 0.02 0.05 t, TIME (SECONDS) 0.1 0.2 PPK t2 DUTY CYCLE, D =t1/t2 t1
SINGLE PULSE TJL = JL (t)PPK REPETITIVE PULSES TJL = JL (t,D)PPK 0.5 1 2 5 10
0.3 0.0001 0.0002
Figure 2. Typical Thermal Response L, Lead Length = 3/8 Inch
1K PPK , PEAK SURGE POWER (WATTS) 500 300 200 100 50 30 20 10 0.1 0.2 0.3 0.5 1 23 5 10 PW, PULSE WIDTH (ms) 20 30 50 100 RECTANGULAR NONREPETITIVE WAVEFORM TJ = 25°C PRIOR TO INITIAL PULSE 3 2 1 0.5 0.2 0.1 0.05 0.02 0.01 0.005 0.002 0.001 0.0005 0.0003 TA = 125°C
IR , REVERSE LEAKAGE (µ Adc) @ VR AS SPECIFIED IN ELEC. CHAR. TABLE
TA = 125°C
1
2
5
10 20 50 100 NOMINAL VZ (VOLTS)
200
400
1000
Figure 3. Maximum Surge Power
Figure 4. Typical Reverse Leakage
APPLICATION NOTE
Since the actual voltage available from a given zener diode is temperature dependent, it is necessary to determine junction temperature under any set of operating conditions in order to calculate its value. The following procedure is recommended: Lead Temperature, TL, should be determined from: TL = LA PD + TA LA is the lead-to-ambient thermal resistance (°C/W) and PD is the power dissipation. The value for LA will vary and depends on the device mounting method. LA is generally 3040°C/W for the various clips and tie points in common use and for printed circuit board wiring. The temperature of the lead can also be measured using a thermocouple placed on the lead as close as possible to the tie point. The thermal mass connected to the tie point is normally large enough so that it will not significantly respond to heat surges generated in the diode as a result of pulsed operation once steady-state conditions are achieved. Using the measured value of TL, the junction temperature may be determined by: TJ = TL + TJL Motorola TVS/Zener Device Data TJL is the increase in junction temperature above the lead temperature and may be found from Figure 2 for a train of power pulses (L = 3/8 inch) or from Figure 10 for dc power. TJL = JL PD For worst-case design, using expected limits of IZ, limits of PD and the extremes of TJ (TJ) may be estimated. Changes in voltage, VZ, can then be found from: V = VZ TJ VZ, the zener voltage temperature coefficient, is found from Figures 5 and 6. Under high power-pulse operation, the zener voltage will vary with time and may also be affected significantly by the zener resistance. For best regulation, keep current excursions as low as possible. Data of Figure 2 should not be used to compute surge capability. Surge limitations are given in Figure 3. They are lower than would be expected by considering only junction temperature, as current crowding effects cause temperatures to be extremely high in small spots resulting in device degradation should the limits of Figure 3 be exceeded. 500 mW DO-35 Glass Data Sheet 6-3
|
|
