|
Details, datasheet, quote on part number:NLAS324
| |
Datasheet text preview:
NLAS324 Dual SPST Analog Switch, Low Voltage, Single Supply
The NLAS324 is a dual SPST (Single Pole, Single Throw) switch, similar to 1/2 a standard 4066. The device permits the independent selection of 2 analog/digital signals. Available in the Ultra-Small 8 package. The use of advanced 0.6 m CMOS process, improves the RON r e s i s t a n c e considerably compared to older higher voltage technologies.
http://onsemi.com MARKING DIAGRAM
8 8 1 US8 US SUFFIX CASE 493
· · · · · · · · · · · ·
On Resistance is 20 W Typical at 5.0 V Matching is 200 MHz, -3 dB CMOS/TTL Compatible 2000 V ESD (HBM) Ron Flatness $ 6 W at 5.0 V US8 Package Negative Enable Switches are Independent
L7
1
D
L7 = Device Code D = Date Code
PIN ASSIGNMENT
1 2 3 NC1 COM1 IN2 GND NC2 COM2 IN1 VCC
NC1
1
8
VCC
4 5 6
COM1
2
7
IN1
7 8
IN2
3
6
COM2
FUNCTION TABLE
GND 4 5 NC2 On/Off Enable Input L H State of Analog Switch On Off
Figure 1. Pinout
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet.
© Semiconductor Components Industries, LLC, 2003
1
January, 2003 - Rev. 3
Publication Order Number: NLAS324/D
NLAS324
MAXIMUM RATINGS
Symbol VCC VI VO IIK IOK IO ICC IGND TSTG TL TJ qJ A PD MSL FR VESD DC Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Sink Current DC Supply Current per Supply Pin DC Ground Current per Ground Pin Storage Temperature Range Lead Temperature, 1 mm from Case for 10 Seconds Junction Temperature under Bias Thermal Resistance Power Dissipation in Still Air at 85_C Moisture Sensitivity Flammability Rating ESD Withstand Voltage Oxygen Index: 28 to 34 Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) (Note 1) VI 2000 > 150 N/A V Unit V V V mA mA mA mA mA _C _C _C _C/W mW
Maximum Ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute maximum-rated conditions is not implied. Functional operation should be restricted to the Recommended Operating Conditions. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2-ounce copper trace with no air flow. 2. Tested to EIA/JESD22-A114-A. 3. Tested to EIA/JESD22-A115-A. 4. Tested to JESD22-C101-A.
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VIN VIO VIS TA tr, tf Positive DC Supply Voltage Digital Input Voltage (Enable) Static or Dynamic Voltage Across an Off Switch Analog Input Voltage (NO, COM) Operating Temperature Range, All Package Types Input Rise or Fall Time, (Enable Input) NORMALIZED FAILURE RATE Vcc = 3.3 V + 0.3 V Vcc = 5.0 V + 0.5 V Characteristics Min 2.0 GND GND GND -55 0 0 Max 5.5 5.5 VCC VCC +125 100 20 Unit V V V V °C ns/V
DEVICE JUNCTION TEMPERATURE VERSUS TIME TO 0.1% BOND FAILURES
Junction Temperature 5C 80 90 100 110 120 130 140 Time, Hours 1,032,200 419,300 178,700 79,600 37,000 17,800 8,900 Time, Years 117.8 47.9 20.4 9.4 4.2 2.0 1.0
FAILURE RATE OF PLASTIC = CERAMIC UNTIL INTERMETALLICS OCCUR TJ = 130_C TJ = 120_C TJ = 100_C TJ = 110_C TJ = 90_C TJ = 80_C 100 TIME, YEARS
1 1 10 1000
Figure 2. Failure Rate vs. Time Junction Temperature
http://onsemi.com
2
NLAS324
DC CHARACTERISTICS - Digital Section (Voltages Referenced to GND)
Guaranteed Max Limit Symbol VIH Parameter Minimum High- Level Input Voltage, Enable Inputs Condition VCC 2.0 3.0 4.5 5.5 2.0 3.0 4.5 5.5 VIN = 5.5 V or GND Enable and VIS = VCC or GND 0 V to 5.5 V 5.5 -55 to 255C 1.5 2.1 3.15 3.85 0.5 0.9 1.35 1.65 +0.1 1.0 <855C 1.5 2.1 3.15 3.85 0.5 0.9 1.35 1.65 +1.0 1.0 <1255C 1.5 2.1 3.15 3.85 0.5 0.9 1.35 1.65 +1.0 2.0 Unit V
VIL
Maximum Low- Level Input Voltage, Enable Inputs
V
IIN ICC
Maximum Input Leakage Current, Enable Inputs Maximum Quiescent Supply Current (per package)
mA mA
DC ELECTRICAL CHARACTERISTICS - Analog Section
Guaranteed Max Limit Symbol RON Parameter Maximum ON Resistance (Figures 8 - 12) ON Resistance Flatness Condition VIN = VIH VIS = VCC to GND IIsI = <10.0mA VIN = VIH IIsI = <10.0mA VIS = 1V, 2V, 3.5V VIN = VIL VNO = 1.0 V, VCOM = 4.5 V or VCOM = 1.0 V and VNO 4.5 V VIN = VIL VNO = 4.5 V or 1.0 V VCOM = 1.0 V or 4.5 V VCC 3.0 4.5 5.5 4.5 -55 to 255C 45 30 25 4 <855C 50 35 30 4 <1255C 55 40 35 5 Unit W
RFLAT(ON)
W
INO(OFF)
Off Leakage Current, Pin 2 (Figure 3)
5.5
1
10
100
nA
ICOM(OFF)
Off Leakage Current, Pin 1 (Figure 3)
5.5
1
10
100
nA
AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns)
Guaranteed Max Limit VCC Symbol tON Parameter Turn-On Time Test Conditions RL = 300 W, CL = 35 pF (Figures 4, 5, and 13) (V) 2.03 .04. 55.5 2.03 .04. 5 5.5 -55 to 255C Min Typ 7.0 5.0 4.5 4.5 11.0 7.0 5.0 5.0 Max 14 10 9 9 22 14 10 10 Min <855C Typ Max 16 12 11 11 24 16 12 12 Typical @ 25, VCC = 5.0 V CIN CNO or CNC CCOM(OFF) CCOM(ON) Maximum Input Capacitance, Select Input Analog I/O (switch off) Common I/O (switch off) Feedthrough (switch on) 8 10 10 20 pF Min <1255C Typ Max 16 12 11 11 24 16 12 12 Unit ns
tOFF
Turn-Of f Time
RL = 300 W, CL = 35 pF (Figures 4, 5, and 13)
ns
http://onsemi.com
3
|
|
