|
Details, datasheet, quote on part number:EPA366-55
| |
Datasheet text preview:
SMD 14 Pin Gull-Wing Quad TTL Compatible Active Delay Modules
DELAY TIME ±5% or ±2 nS PART NUMBER DELAY TIME ±5 or ±2 nS PART NUMBER DELAY TIME ±5% or ±2 nS PART NUMBER
5 6 7 8 9 10 11 12 13 14 15 Whichever is greater.
EPA366-5 EPA366-6 EPA366-7 EPA366-8 EPA366-9 EPA366-10 EPA366-11 EPA366-12 EPA366-13 EPA366-14 EPA366-15
16 17 18 19 20 21 22 23 24 25 30
EPA366-16 EPA366-17 EPA366-18 EPA366-19 EPA366-20 EPA366-21 EPA366-22 EPA366-23 EPA366-24 EPA366-25 EPA366-30
35 40 45 50 55 60 65 70 75
EPA366-35 EPA366-40 EPA366-45 EPA366-50 EPA366-55 EPA366-60 EPA366-65 EPA366-70 EPA366-75
Delay times referenced from input to leading edges at 25°C, 5.0V, with no load.
DC Electrical Characteristics Parameter Test Conditions
VOH VOL VIK IIH IIL IOS ICCH ICCL TRO NH NL High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current Low-Level Input Current Short Circuit Output Current High-Level Supply Current Low-Level Supply Current Output Rise Time Fanout High-Level Output Fanout Low-Level Output VCC = min. VIL = max. I OH = max VCC = min. VIH = min. IOL= max VCC = min. II = IIK VCC = max. VIN = 2.7V VCC = max. VIN = 5.25V VCC = max. VIN = 0.5V VCC = max. VOUT = 0. (One output at a time) VCC = max. VIN = OPEN VCC = max. VIN = 0 VCC = max. VOH = 2.7V VCC = max. VOL = 0.5V
Schematic Min Max Unit
2.7 0.5 -1.2V 50 1.0 -2 -100 V V V µA mA mA mA
14 VCC 12 10
1 9
3
-40
8
150 mA 150 mA 4 nS 20 TTL LOAD 10 TTL LOAD
4
5
7 GROUND
Recommended Operating Conditions
VCC VIH VIL IIK IOH IOL PW* d* TA Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature
Package Dimensions Min
4. 75 2. 0
Max
5.25 0.8 -18 -1.0 20
Unit
V V V mA mA mA % % °C
.055
.400 Max.
40 0 40 +70
PCA EPA366-5 Date Code
.280 Max.
Suggested Solder Pad Layout
.410
.100 .780 Max. .250 Max. .01 Typ.
.03
*These two values are inter-dependent.
Input Pulse Test Conditions @ 25° C
EIN PW TRI PRR VCC Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage 3.2 110 2.0 1.0 100 5.0
Unit
Volts % nS MHz KHz Volts
.02
.100
.050
.300
DSA366 Rev. A 2/5/96
QAF-CSO1 Rev. B 8/25/94
Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 16 .XX = ± .030 .XXX = ± .010
ELECTRONICS
INC.
16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791
|
|
