|
|
Part: EPT7069G
Category:
Description: Token Ring Front End Filter Module 120 Ohm
Company: PCA Electronics Inc.
Datasheet: Download EPT7069G datasheet File size : 78 kB
Request For quote: Find where to buy EPT7069G
Datasheet text preview:
120 Token Ring Front End Filter Module
ELECTRONICS INC.
EPT7069G
· Recommended for use in both UTP and STP · · Enhanced Common Mode Rejection Capability · · Robust construction in low profile allows for severe soldering processes · · Complies with or exceeds IEEE 802.5 Requirements ·
Electrical Parameters @ 25° C
Impedance [Xmit/Rcv] Media Side 150 Cable Side 120 Insertion Loss (dB) 1-16 32 36 44 MHz (Max.) MHz (Min.) MHz (Min.) MHz (Min.) -.8 -7 -18 -30 1-6 MHz -18 Return Loss (dB Min.) 6-17 MHz -12 17-25 MHz -8 1-30 MHz -40 Common Mode Rejection (dB Min.) 30-100 MHz -20 100-200 MHz -15 200-300 MHz -10
Schematic
7 XMT+ 2 150 XMT- 3 Filter 11 B2-COM 1.118:1 10 B1-120 8 12 A2-COM 13 A1-120
GND A 4 GND 6
Pins 1, 5, 9 & 14 are not connected.
Package
A J
Pin 1 I.D. PCA EPT7069G Date Code
Dimensions
N
Dim. A B C D E F G H I J K L M N P Q Min. .780 .510 .090 .595 .003 .097 .660 .017 .008 .090 0° .025 (Inches) Max. Nom. .800 .530 .100 .605 .010 .103 .680 .022 .013 .100 8° .045 .790 .520 .095 .600 .005 .100 .670 .020 .011 .095 4° .040 .030 .100 .085 .700 (millimeters) Min. Max. Nom. 19.81 12.95 2.29 15.11 .076 2.46 16.76 .432 .203 2.29 0° .635 20.32 13.46 2.54 15.37 .254 2.62 17.27 .559 .330 2.54 8° 1.14 20.07 13.21 2.41 15.24 .127 2.54 17.02 .508 2.79 2.41 4° 1.02 .762 2.54 2.16 17.78
B
Q
Pad Layout
P
D E C
M K L I
H
F
G
PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343
CST7069Ga Rev. 1
7/7/98
Product performance is limited to specified parameters. Data is subject to change without prior notice.
TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pca.com
120 Token Ring Front End Filter Module
ELECTRONICS INC.
EPT7069G
The circuit below is a guideline for interconnecting PCA's EPT7069G with a typical Token Ring PHY chip for 4 Mb/16Mb applications over STP or UTP cable. Further details of system design should be obtained from the specific chip manufacturer. Note that this module is optimized for a "voltage source" driver such as TI380C series. Only one type of cable should be driven by the module: either UTP or STP. This module is ideally suited for applications with only one RJ45 connector installed. Changing to STP is accomplished by using an adaptor without any need for additional impedance transforming device embedded in it. The same approach is usable if one were to drive the European standard 120 cable, which poses no problems. Note that the receiver side filtering is identical, thus making it possible for use in a DTR application as well. Consider this a cost effective solution for almost all Token Ring applications using this chip or similar chips. The pull down resistors to chassis via a cap shown around the RJ45 connector have been known to suppress unwanted radiation that unused wires pick up from the immediate environment. This is specially true if driving UTP cable. Their placement and use are to be considered carefully before a design is finalized. No specific recommendation is made here for phantom circuitry, implementation varies. Please note that additional emission control has been observed if both nodes of the phantom bypass capacitor on the transmit channel are pulled to the chassis ground via suitable capacitors. It is recommended that there be a neat separation of ground planes in the layout. It is generally accepted practice to limit the plane off at least 0.05 inches away from the chip side pins of EPT7069G. There need not be any ground plane beyond this point. For best results, PCB designer should design the outgoing traces preferably to be 75/50, balanced and well coupled to achieve minimum radiation from these traces.
Typical Application Circuit Connection to TI380C30 (or Equivalent)
Rcv+
150
2 3 12 11 Rcv Channel
13 10
Rcv-
EPT7069G
+5V +5V 50/2W
6 4 Chassis Ground
PHOUTA PHOUTB
11
50/2W 10µF 10µF
12 Xmit Channel 13 10 C*
4 RU 5 3 TU 6 1 2 7 8
RJ45
TI380C30
Xmit+
100
442
2
EPT7069G
6 4 Chassis Ground
XmitNotes : 1. 2. 3. 4.
100
3
Suggested phantom circuit is for reference only. Applications Vary. Phantom return on Rcv channel at pins 11 and 12 are not shown. Your application may suffice by using an external inductor pulled to ground. C* : Primary center taps may be pulled to ground by Caps to enhance common mode attenuation.
PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343
CST7069Gb Rev. 1
7/7/98
TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pca.com
Others parts begin by ep
EP-1 EP-2 EP-3 EP-4 EP-5 EP-6 EP-7 EP-8 EP-9 EP-10 EP-11 EP-12 EP-13 EP-14 EP-15 EP-16 EP-17 EP-18 EP-19 EP-20 EP-21 EP-22 EP-23 EP-24 EP-25 EP-26 EP-27 EP-28 EP-29 EP-30 EP-31 EP-32 EP-33 EP-34 EP-35 EP-36 EP-37 EP-38 EP-39 EP-40 EP-41
|
|
|
