|Category||Analog & Mixed-Signal Processing => Switches & Multiplexers => Analog Switches|
|Description||CSP Low Voltage Dual SPDT Audio Clickless Analog Switch with Headphone/Mute Detection, 2:1 Mux/DeMux Bus Switch
fast single-pole double throw (SPDT) CMOS switch. It can be used as an analog switch or as a low-delay bus switch. Specified over a wide operating power supply voltage, 1.65V to 5.5V, the PI5A4765 has a low On-Resistance of 0.6§Ù @ 2.7V.Break-before-make switching prevents both switches being enabled simultaneously. This eliminates signal disruption during switching. The control input, INX, tolerates input drive signals up to 6.0V, independent of supply voltage.The PI5A4765 offers a headphone & mute detection function through utilization of an on-chip comparator. When the negative terminal of the comparator (COMP-) is less than the threshold (internally set to VCC/3, COMP0 (comparator output) is a logic high. A logic low on COMP0 occurs when COMP- rises above the the threshold.PI5A4765 also offers shunt switches connected to ground in order to dissipate capacitance that builds up on the unconnected NC or NO line. As a result, reduction of popping and clicking sounds is achieved when switching between audio sources.
|Company||Peregrine Semiconductor Corp.|
|Datasheet||Download PI5A4765 datasheet
Low Voltage Dual SPDT Audio Clickless Analog Switch with Headphone/Mute Detection 2:1 Mux/DeMux Bus SwitchFeatures
CMOS Technology for Bus and Analog Applications Low On-Resistance: @ 2.7V. Wide VCC Range: to 5.5V Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5V min. High Off Isolation: -50dB Crosstalk Rejection Reduces Signal Distortion: -80dB Break-Before-Make Switching Extended Industrial Temperature Range: to 85°C Packaging (Pb-free & Green available): -12-ball CSPDescription
Pericom Semiconductors is a dual high-bandwidth, fast single-pole double throw (SPDT) CMOS switch. It can be used as an analog switch as a low-delay bus switch. Specified over a wide operating power supply voltage, to 5.5V, the PI5A4765 has a low On-Resistance @ 2.7V. Break-before-make switching prevents both switches being enabled simultaneously. This eliminates signal disruption during switching. The control input, INX, tolerates input drive signals to 6.0V, independent of supply voltage. The PI5A4765 offers a headphone & mute detection function through utilization of an on-chip comparator. When the negative terminal of the comparator (COMP-) is less than the threshold (internally set VCC/3, COMP0 (comparator output) is a logic high. A logic low on COMP0 occurs when COMP- rises above the threshold. PI5A4765 also offers shunt switches connected to ground in order to dissipate capacitance that builds up on the unconnected or NO line. As a result, reduction of popping and clicking sounds is achieved when switching between audio sources.Applications
Cell Phones PDAs MP3 players Portable Instrumentation Computer Peripherals Speaker Headset Switching Power Routing Relay Replacement Audio/Video Signal Routing PCMCIA Cards ModemsPin Configuration / Block Diagram (top view) Pin Description
Data Port (Normally open) Positive Power Supply Data Port (Normally closed) Ground Common Output/Data Port Comparator Output Comparator Input Logic ControlLogic Input (INX) 0 1 Note: or 2 Function NCX Connected to COMX NOX Connected to COMX
Low Volt. Dual SPDT Analog Switch 2:1 Mux/DeMux Bus Switch (w/Comparator & Shunt Switches)
Supply Voltage VCC............................................ +7V DC Switch Voltage 0.5V to VCC +0.5V DC Input Voltage +7.0V DC Output Current (VOUT)........................................... 128mA DC VCC or Ground Current (ICC/IGND)....................... ±100mA Storage Temperature Range (TSTG).............. to +150°C Junction Temperature under Bias (TJ).............................150°C Junction Lead Temperature (TL) (Soldering, 10 seconds)................................................260°C Power Dissipation (PD) +85°C.................................. 180mW
Supply Voltage Operating (VCC). to 5.5V Control Input Voltage (VIN). 0V to VCC Switch Input Voltage (VIN). 0V to VCC Output Voltage (VOUT). 0V to VCC Operating Temperature (TA). to +85°C Input Rise and Fall Time (tr,tf) Control Input VCC to 10ns/V Control Input VCC to 5ns/V Thermal Resistance (JA). 350°C/W
Notes: 1. Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. 2. The input and output negative voltage ratings may be exceeded if the inut and output diode current ratings are observed. 3. Control input must be held HIGH or LOW; it must not float.
(VCC TA = TMIN to TMAX, unless otherwise noted. Typical values are at 3V and +25°C.) Test Conditions TA Min. Typ. Max. Units
Analog Signal Range NC On-Resistance NO On-Resistance Match Between Channels NC On-Resistance Flatness NO On-Resistance Flatness Shunt Switch Resistance or NC Off Leakage Current COM On Leakage Current VNO , VNC , VCOM RON(NC) RON(NO) RON RONF(NC) RONF(NO) RSH IOFF (NO) or IOFF (NC) ICOM (ON) VCC = 2.7V, ICOM = 100mA, VNC = 0 toVCC VCC = 2.7V, ICOM = 100mA, VNO 0 to VCC = 2.7V, ICOM = 100mA, VNO or VNC = 1.5V VCC = 2.7V, ICOM = 100mA, VNC 0 to VCC = 2.7V, ICOM = 100mA, VNO 0 to VCC INO or INC = 10mA, VCC = 2.7V VCC = 2.7V, VNC or VNO 0.3V, +2.5V, VCOM +2.5V, 0.3V VCC = 2.7V, VNC or VNO 0.3V, +2.5V, VCOM nA 0.4 VCC V
Input Logic High Input Logic Low IN Input Leakage Current VIH VIL IIN VCC to 3.6V VCC to 5.5V VCC to 3.6V VCC to 5.5V VIN 0 or VCC µA V
Comparator Output High Voltage Comparator Output Low Voltage Comparator Input Leakage Current Comparator Switching Time Comparator Power Supply Range Comparator Threshold ISOURCE = 1mA ISINK = 1mA VCMP- to 2.7V VCC = 2.7V, VCMP- 0V to VCC, from 50% of VCMP- VCMP0 1.8 VCC µS V
|Some Part number from the same manufacture Peregrine Semiconductor Corp.|
|PI5A4764 CSP Low Voltage Dual SPDT Audio Clickless Analog Switch, 2:1 Mux/DeMux Bus Switch (with Shunt Switches) Pericom Semiconductor's PI5A4764 is a dual high-bandwidth, fast single-pole double throw (SPDT)|
|PI5A4213 CSP Low Voltage Dual SP3T Analog Switch, 3:1 Mux/DeMux Bus Switch Pericom Semiconductor's PI5A4213 is a dual high-bandwidth, fast single-pole triple throw (SP3T) CMOS switch. It can be used as an analog|
|PE97632 PE976323.0 GHz Delta-Sigma modulated Fractional-N PLL Frequency Synthesizer for Low Phase Noise ApplicationsPeregrine's PE97632 is a high performance fractional-N PLL capable of frequency synthesis|
|PE42742 The PE42742 is a SPDT Switch designed for CATV applications. It offers high isolation and low insertion loss in both a powered and a unique unpowered default state. The PE42742 covers a broad frequency|
|PE4309 This product is a high linearity, 6-bit RF Digital Step Attenuator (DSA) covering a 31.5 dB attenuation range in 0.5 dB steps. The Peregrine 50Ω RF DSA provides a parallel CMOS control interface and it operates|
|PE42612 The PE42612 SP4T RF UltraCMOS� Flip Chip Switch is designed specifically to address the needs of the antenna switch module market for GSM Handsets. It supports 1.8 V control logic and is offered|
|PE42691 SP9T RF UltraCMOS� Switch Featuring HaRP� technology enhancementsThe PE42691 is a HaRP�-enhanced SP9T RF Switch developed on the UltraCMOS� process technology. It addresses|
|PE42632 SP6T RF UltraCMOS� Switch Featuring HaRP� technology enhancementsThe PE42632 is a HaRP�-enhanced SP6T RF Switch developed on the UltraCMOS� process technology. This 50 Ω|
|PE42801 SPDT CATV UltraCMOS� SwitchThe PE42801 is a high-isolation CMOS Switch designed for CATV applications, covering a broad frequency range from DC up to 2.2 GHz. This single-supply SPDT switch integrates|
|PE97022 3.5 GHz Integer-N PLL For Rad Hard ApplicationsPeregrine\'s PE97022 is a high-performance integer-N PLL capable of frequency synthesis up to 3.5 GHz. The device is designed for superior phase noise performance|
|PE97042 3.5 GHz Integer-N PLL For Rad Hard ApplicationsPeregrine\'s PE97042 is a high-performance integer-N PLL capable of frequency synthesis up to 3.5 GHz. The device is designed for superior phase noise performance|
|PE42641 SP4T UltraCMOS™ RF SwitchThe PE42641 is a HaRP™-enhanced SP4T RF Switch developed on the UltraCMOS™ process technology. This switch contains 4 identical WEDGE/CDMA compliant TX paths and can be used|
|PI2EQX5804 5.0Gbps 4-lane PCIe Gen2 RedriverThe first family of PCIeG2-specific signal conditioning products in the industry, the PI2EQX5804 and PI2EQX5864 PCIeG2 ReDriver conditioners are specifically designed|
|PE43701 50-ohm, 7-bit RF Digital Attenuator0.25 DB Steps To 31.75 DB, DC – 3.0 GHzFeaturing HaRP?? Technology EnhancementsThe PE43701 is a HaRP??-enhanced, high linearity, 7-bit RF Digital Step Attenuator|
|PE43404 75-ohm, 4-bit RF Digital Attenuator1.0 DB Steps To 15 DB, DC – 2.0 GHzThe PE43404 is a high linearity, 4-bit RF Digital Step Attenuator (DSA) covering a 15 dB attenuation range in 1.0 dB steps. This|
|PE42552 SPDT UltraCMOS?? RF SwitchTest Equipment/ATE MarketFeaturing HaRP?? Technology EnhancementsThe PE42552 RF Switch is designed for use in Test/ATE, cellular and other wireless applications. This broadband|
|PE9309 13.0 GHz Low Power CMOS Divide-by-4 Prescaler For Rad-Hard ApplicationsThe PE9309 is a high-performance dynamic UltraCMOS? prescaler with a fixed divide ratio of 4. Its operating frequency range is 3.5 GHz to 13.0|
PE3513-06SC70-3000C : Product Description = Divide-by-8 ;; Input Operating Freq. Range (MHz) = DC - 1000 ;; Divide Ratio = 8 ;; Total Icc MA@3V = 8 ;; VCC Range (V) = 2.85 - 3.15 ;; Package Types = 6L SC70
PE4210-EK : MOSFET Switches Product Description = Reflective SPDT ;; Operating Frequency (MHz) = DC - 3000 ;; P1dB (dBm) = 15 ;; Insertion Loss (dB, 1GHz) = 0.30 ;; ISOlation (dB, 1GHz) = 36 ;; Package Types = 8L Msop
PE4249-06MLP3X3-EK : MOSFET Switches Product Description = Absorbtive SPST ;; Operating Frequency (MHz) = DC - 1300 ;; P1dB (dBm) = 33 ;; Insertion Loss (dB, 1GHz) = 0.80 ;; ISOlation (dB, 1GHz) = 60 ;; Package Types = 6L MLPM
PE9702-00 : Space Application Product Description = W/ Phase Detector ;; Max Input Operating Freq. (MHz) Rf-pll = 3000 ;; Max Input Operating Freq. (MHz) Reference = 100 ;; Max Input Operating Freq. (MHz)Compare = 20 ;; Dual-mod Prescaler = 10/11 ;; Main Counter M, a = 9bit, 4bit ;; Reference Counter = 6bit ;; Package Types = 44
PE42801 : SPDT CATV UltraCMOS� Switch The PE42801 is a high-isolation CMOS Switch designed for CATV applications, covering a broad frequency range from DC up to 2.2 GHz. This single-supply SPDT switch integrates a two-pin CMOS control interface. It also provides low insertion loss with extremely low b
PE42510AMLI-Z : SPDT High Power Ultracmos RF Switch 30 - 2000 MHz
83511-01 : DC - 1500 MHz Low Power Ultracmos Divide-by-2 Prescaler Military Operating Temperature Range
4302-00 : 50 Ohm RF Digital Attenuator 6-bit, 31.5 dB, Dc-4.0 GHZ
9763-11 : 3.2 GHz Delta-sigma Modulated Fractional-n Frequency Synthesizer for Low Phase Noise Applications
42671-00 : SP7T Ultracmos 2.75 V Switch 100 - 3000 MHz, +68 dBm IIP3
3339-12 : 3.0 GHz Integer-n PLL for Low Phase Noise Applications
CHP1230 : HBT Single Supply Module, 1720-1780 MHZ. Preliminary Product s July of 6) InGaP HBT Technology 6mm Square, 50 Ohm Power Module Single Positive Supply 35% Linear Power Added Efficiency +28.5 dBm Output Power (CDMA) +28.0 dBm Output Power 30 dB Gain at Operating Output Power On-Board Power Down Mode Applications Korea PCS Handsets CDMA Handsets CDMA2K 1X Handsets The a 50 ohm matched, single.
LA7054 : Video, Audio Signal Processor For UHF Band RF Modulator. Video, Audio Signal Processor for UHF Band RF Modulator The is a video, audio signal processor IC for UHF unit: mm band RF modulators. It performs the functions of TSG (test 3017C-SIP9 signal generator), video clamp circuit, white clip circuit, audio FM modulator. It is highly stable to supply voltage variations because the LA7054 has an internal voltage.
LM6317 : Single. High Speed, Voltage Feedback Amplifier (discontinued). LM6317 120 MHz Fast Settling Low Power Voltage Feedback Amplifier The is a high speed unity-gain stable voltage feedback amplifier that consumes only mW of quiescent power Operating g 5V power supply the LM6317 provides excellent AC performance such as 120 MHz of unity-gain bandwidth ms of slew rate and dB of SFDR The LM6317 has the slew characteristic.
LP239 : Low-power Quad Differential Comparators. Ultralow Power Supply Current Drain. 60 µA Typ Low Input Biasing Current. 3 nA Low Input Offset Current. ±0.5 nA Low Input Offset Voltage. ±2 mV Common-Mode Input Voltage Includes Ground Output Voltage Compatible With MOS and CMOS Logic High Output Sink-Current Capability = 2V) Power Supply Input Reverse-Voltage Protected Single-Power-Supply Operation.
MAX320 : Precision, Dual Supply, Spst, Analog CMOS Switches. The MAX320/MAX321/MAX322 are precision, dual, SPST analog switches designed to operate from to ±8V dual supplies. The MAX320 has two normally open (NO) switches and the MAX321 has two normally closed (NC) switches. The MAX322 has one NO and one NC switch. Low power consumption (1.25mW) makes these parts ideal for battery-powered equipment. They offer.
MAX4361 : Adsl Drivers/receivers For Customer Premise Equipment. The MAX4361/MAX4362/MAX4363 are a family of highperformance ADSL drivers and drivers/receivers ideal for the upstream transmit path and the downstream receive path of customer premise equipment. These devices operate from a single 5V supply and deliver to 12.5dBm average line power for DMT modulated signals, meeting the requirements of full-rate ADSL.
MAX4565 : Quad Dual, Low-Voltage, Bidirectional RF Video Switches. The MAX4565/MAX4566/MAX4567 are low-voltage T-switches designed for switching RF and video signals from in 50 and 75 systems. The MAX4565 contains four normally open single-pole/singlethrow (SPST) switches. The MAX4566 contains two dual SPST switches (one normally open, one normally closed.) The MAX4567 contains two single-pole/double-throw (SPDT) switches.
MAX4601 : 2.5, Quad, Spst, CMOS Analog Switches. The MAX4601/MAX4602/MAX4603 quad analog switches feature low on-resistance of 2.5 max. On-resistance is matched between switches to 0.5 max and is flat (0.5 max) over the specified signal range. Each switch can handle Rail-to-Rail® analog signals. The offleakage current is only 2.5nA maximum = +85°C. These analog switches are ideal in low-distortion.
MAX9107 : 25ns, Dual/Quad/Single, Low-Power, TTL Comparators. The MAX9107/MAX9108/MAX9109 dual/quad/single, high-speed, low-power voltage comparators are designed for use in systems powered from a single +5V supply. Their 25ns propagation delay (with 10mV input overdrive) is achieved with a power consumption of only 1.75mW per comparator. The wide input common-mode range extends from 200mV below ground to within.
MCP6291 : . Gain Bandwidth Product: 10 MHz (typ.) Supply Current: 1.0 mA Supply Voltage: to 5.5V Rail-to-Rail Input/Output Extended Temperature Range: to +125°C Available in Single, Dual and Quad Packages Single with Chip Select (CS) (MCP6293) The Microchip Technology Inc. MCP6291/2/3/4 family of operational amplifiers (op amps) provide wide bandwidth for the current.
OPA2341 : . SINGLE-SUPPLY, RAIL-TO-RAIL OPERATIONAL AMPLIFIER WITH SHUTDOWN microAmplifier TM Series RAIL-TO-RAIL INPUT AND OUTPUT SWING MicroSIZE PACKAGES BANDWIDTH: 5.5MHz SLEW RATE: 6V/µs QUIESCENT CURRENT: 750µA/Chan POWER SHUTDOWN MODE APPLICATIONS SENSOR BIASING SIGNAL CONDITIONING DATA ACQUISITION PROCESS CONTROL ACTIVE FILTERS TEST EQUIPMENT The OPA341.
OPA336N/250 : ti OPA336, Single-Supply, Micropower CMOS Operational Amplifiers MicroAmplifier(TM) Series.
OPA445AP : Power Operational Amplifiers. ti OPA445, High Voltage Fet-input Operational Amplifier.
TLC072A : . TLC075, TLC07xA FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY OPERATIONAL AMPLIFIERS Wide Bandwidth. 10 MHz High Output Drive IOH. mA at VDD V IOL. 0.5 V High Slew Rate SR+. 16 V/µs SR. 19 V/µs Wide Supply Range. 16 V Supply Current. 1.9 mA/Channel Ultralow Power Shutdown Mode IDD. 125 µA/Channel Low Input Noise Voltage. 7 nVHz Input.
TLV2702ID : ti TLV2702, op Amp (1) + Push-pull Comparator (1) Combo ic. FAMILY OF NANOPOWER OPERATIONAL AMPLIFIERS AND PUSH-PULL COMPARATORS D Micro-Power Operation. µA D Input Common-Mode Range Exceeds the Rails. V to VCC 5 V Supply Voltage Range. 16 V Rail-to-Rail Input/Output (Amplifier) Reverse Battery Protection 18 V Gain Bandwidth Product. 5.5 kHz (Amplifier) Push-Pull CMOS Output Stage (Comparator) Specified Temperature.
TOP232 : Power. 0-75 W Flyback Design,energy Efficient, Extended Feature Family.
AD8682 : Dual Precision, Low Power High Speed JFET Product The AD8682 and AD8684 are dual low power, precision (1mV) JFET amplifier featuring excellent speed at low supply currents. The slew rate is typically 9V/μs with a supply current under 250 μA per amplifier. These unity-gain stable amplifiers have a typical gain bandwidth of 4 MHz. The JFET input.
ADA4858-3 : Single-Supply, High Speed, Triple Op Amp With Charge Pump The ADA4858-3 (triple) is a single-supply, high speed current feedback amplifier with an integrated charge pump that eliminates the need for negative supplies in order to output negative voltages or output a 0 V level for video applications. The 600 MHz ?3 dB bandwidth and 600 V/?s slew rate.