Details, datasheet, quote on part number: PI4S706SW
CategoryPower Management => Supervisory Circuits => Microprocessor Supervisors
Description4.63V Reset Active Low Supervisor
CompanyPericom Semiconductor Corporation
DatasheetDownload PI4S706SW datasheet
Cross ref.Similar parts: TPS3705-30D, TPS3705-33D, BQ2002, BQ2002C, BQ2002F, BQ2002G, BQ2002T, BQ24400, BQ24401, INA270
Find where to buy


Features, Applications

Precision supply-voltage monitor PI4S708R) 200ms reset pulse width Debounced TTL/CMOS-compatible manualreset input Independent watchdog timer with 1.6sec time-out 706x, 706xH, and 813L ONLY Reset output signal: - Active-low only 706R) - Active-high only 706P) - Active-high and active-low 708S, 708R) Voltage monitor for power-fail or low battery warning Guaranteed RESET/RESET valid at VCC = 1.2V


The PI4S70xxx/PI4S813L family microprocessor (ÁP) supervisory circuits are targeted to improve reliability and accuracy of power-supply circuitry in ÁP systems. These devices reduce the complexity and number of components required to monitor power-supply and battery functions. The main functions are: 1. Asserting reset output during power-Áp, power-down and brownout conditions for ÁP systems. 2. Detecting power failure or low-battery conditions with a 1.25V threshold detector. 3. Generating an independent watchdog output that goes low if the watchdog input has not been toggled within 1.6 seconds. 4. Asserting reset output with an active-low manual-reset input


Computers Controllers Intelligent Instruments Automotive Systems Printers Critical Microprocessor Power Monitoring

Pin Name MR VCC GND PFI PFO Type Input Power Ground Input Output Description Manual-Reset: triggers a reset pulse when pulled below 0.8V, active low. It has an internal 250A pull-up current and can be driven from a TTL or CMOS logic line as well as shorted to ground with a switch. Power Supply Ground Reference for all signals Power-Fail Voltage Monitor Input: When PFI is less than 1.25V, PFO goes low. Connect PFI to GND or Vcc when not used. Power-Fail Output: it gets low and sinks current when PFI is less than 1.25V; otherwise PFO stays high. Watchdog Input: If WDI remains high or low for 1.6sec, the internal watchdog timer runs out and WDO goes low. Floating WDI or connecting WDI to a high-impedance three-state buffer disables the watchdog feature. The internal watchdog timer clears whenever reset is asserted, WDI is three-stated, or WDI sees a rising or falling edge. No Connect Output Reset Output pulses: low for 200ms when triggered, and stays low whenever Vcc is below the reset threshold. It remains low for 200ms after VCC rises above the reset threshold or MR goes from low to high. A watchdog timeout will not trigger RESET unless WDO is connected to MR. Watchdog Output: pulls low when the internal watchdog timer finishes its 1.6sec count and does not go high again until the watchdog is cleared. WDO also goes low during low-line conditions. Whenever Vcc is below the reset threshold, WDO stays low; however, unlike RESET, WDO does not have minimum pulse width. As soon as VCC rises above the reset threshold, WDO goes high with no delay. The inverse of RESET: active high. Whenever RESET is high, RESET is low.


Related products with the same datasheet
Some Part number from the same manufacture Pericom Semiconductor Corporation
PI4S706T 4.63V Reset Active Low Supervisor
PI5318A Precision Wide Bandwidth Analog Switch
PI5A100 Single Supply, High Speed, Quad SPDT CMOS Analog Switch W/master Enable
PI5A101 Single Supply, Quad SPST Analog Switch (NC)
PI5A121 High Speed SPST Analog Switch W/compact Packages
PI5A125 Single Wide Bandwidth Analog Switch
PI5A126 High Speed Dual SPST Analog Switch
PI5A3157 Sotiny Single SPDT Mux/demux Switch
PI5A3158 Sotiny Dual SPDT Mux/demux Switch
PI5A3159 Sotiny 1 Ohm, Low-Voltage, SPDT Analog Switch (3157 Pinout)
PI5A317A High Speed, Single Supply SPST Switch
PI5A318AP Precision Wide Bandwidth Analog Switch
PI5A319A High Speed, Single Supply SPST Switch
PI5A381A Precision Wide Bandwidth Analog Switches
PI5A383A High Speed, Single Supply Dual SPDT Switch
PI5A385A Precision Wide Bandwidth Analog Switch
PI5A391A 7V Quad SPST
PI5A4594A Sotiny Low-Voltage, Single-Supply, 8-Ohm SPST CMOS Analog Switches
PI5A4599A Sotiny Single SPDT Mux/demux Switch

PI5C32X384CB : Bus Oriented Circuits 20-Bit Bus Switch

PI74LPT541A : CMOS/BiCMOS->LVT/ALVT/LCX/LPT Family->Low Voltage Non-inverting Octal Buffer/line Driver (3-State)

PI3B16245VE : 3.3v, 24-bit to 48-bitmux/demux Nanoswitch

PT7C4050ADE : PLL with Integrated VCXO

PI90LV017AWE : Single LVDS Driver

PI74FCT2245CTHE : FCT SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, PDSO16 Specifications: Counter Type: BINARY COUNTER ; Counter Category: Synchronous ; Counter Direction: UP ; Supply Voltage: 5V, 5.25 ; Package Type: 0.150 INCH, PLASTIC, QSOP-16 ; Logic Family: CMOS, FCT ; Number of Pins: 16 ; Number of Stages (Bits): 4 bits ; Operating Temperature: -40 to 85 C (-40 to 1

PI74FCT651CTR : FCT SERIES, 8-BIT TRANSCEIVER, INVERTED OUTPUT, PDSO20 Specifications: Technology: CMOS ; Device Type: Transceiver ; Supply Voltage: 5V ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Package Type: TSSOP, 0.173 INCH, PLASTIC, TSSOP-20 ; Pins: 20

S5293LS-FREQ : TCXO, CLIPPED SINE OUTPUT, 8.4672 MHz - 34.368 MHz Specifications: Oscillator Type: TCXO ; Package / Form Factor: Through Hole ; Frequency: 8.47 to 34.37 MHz ; Operating Temperature: -15 to 55 C (5 to 131 F) ; Supply Voltage: 5.0 Volts ; Output Type: Sine Wave Output

0-C     D-L     M-R     S-Z