Details, datasheet, quote on part number: PI5C16214
PartPI5C16214
CategoryLogic => Bus Interface => Bus Oriented Circuits
TitleBus Oriented Circuits
DescriptionPi5c162214 (25ohm)
CompanyPericom Semiconductor Corporation
DatasheetDownload PI5C16214 datasheet
  

 

Features, Applications

Features

Near-zero propagation delay 5 switches connect inputs to outputs Direct bus connection when switches are ON Ultra-low quiescent power (0.2A typical) ideally suited for notebook applications Industrial operating temperature: to +85C Packages available: 56-pin 240-mil wide plastic TSSOP (A) 56-pin 300-mil wide plastic SSOP (V)

Pericom Semiconductors PI5C series of BusSwitch circuits are produced in the Companys advanced 0.8 micron CMOS technology, achieving industry leading speed. The PI5C16214 and PI5C162214 are 3-to-1 bus-select switches designed with a low ON resistance (5) allowing inputs to be connected directly to outputs. These devices operate as 12-bit bus switches via the data select pins (S0-S2). The PI5C162214 device has a built-in 25-ohm series resistor to reduce noise resulting from reflections, thus eliminating the need for an external terminating resistor.

Note: H = High Voltage Level L = Low Voltage Level Z = High Impedance

(Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature............................................................ to +150C Ambient Temperature with Power Applied........................... to +85C Supply Voltage to Ground Potential (Inputs & Vcc Only)..... to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only).. +7.0V DC Input Voltage.................................................................... +7.0V DC Output Current............................................................................... 120mA Power Dissipation.................................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

Parameters Description VIH VIL II Input HIGH Voltage Input LOW Voltage Input Current Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = 5.5V., VIN 5.5V OR GND VCC = 0V, VIN = VCC IOZH VIK IOS VH RON High Impedance Output Current Clamp Diode Voltage Short Circuit Current

Input Hysteresis at Control Pins Switch On Resistance

Parameters(5) CIN COFF Description Input Capacitance A/B Capacitance, Switch Off Test Conditions VIN or 3V VIN or 3V Typ 4.5 5.5 Units pF

Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 25C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. 5. This parameter is determined by device characterization but is not production tested.

Parameters Description ICC ICCD Quiescent Power Supply Current Supply Current per Input @ TTL HIGH Supply Current per Input per MHz(4) Test Conditions(1) VCC = Max. VCC = Max. VCC = Max., A and B Pins Open Control Input Toggling 50% Duty Cycle VIN = GND or VCC VIN = 3.4V(3) Min. Typ(2) 0.1 Max. 2.5 0.25 Units A mA mA/ MHz

Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at Vcc 5.0V, +25C ambient. 3. Per TTL driven input (VIN = 3.4V, control inputs only); A and B pins do not contribute to Icc. 4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant or DC currents as they transition. This parameter is not tested, but is guaranteed by design.

PI5C16214 Vcc 5V 0.5V Parameters tPLH tPHL tPZH tPZL tPHZ tPLZ Description Propagation Ax to Bx, to Ax Bus Enable Time XOE or Bx Bus Disable Time XOE 50pF RL Min. Max. 5.5 ns Units

PI5C162214 Vcc 5V 0.5V Parameters tPLH tPHL tPZH tPZL tPHZ tPLZ Description Propagation Ax to Bx, to Ax Bus Enable Time XOE or Bx Bus Disable Time XOE 50pF RL Min. Max. 5.5 ns Units

Notes: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Pericom Semiconductor Corporation 2380 Bering Drive San Jose, 95131 1-800-435-2336 Fax (408) 435-1100 http://www.pericom.com


 

Related products with the same datasheet
PI5C16214A
PI5C16214V
Some Part number from the same manufacture Pericom Semiconductor Corporation
PI5C16214A Pi5c162214 (25ohm)
PI5C16215C 20-Bit Bus Switch W/undershoot Protection
PI5C162209 18-bit Bus Exchange Switch
PI5C162210 20-bit, 2-port Bus Switch
PI5C162212 24-bit Bus Exchange Switch
PI5C162213A
PI5C162213V
PI5C162214 12-bit, 3-to-1 Bus-select Switch
PI5C162215CA 20-bit,hot Insertion,bus Switch With Precharged Outputs & Undershoot Protection
PI5C162215CB
PI5C162244 16-Bit Bus Switch W/25 Ohm Resistor (FCT16244 Pinout)
PI5C162245 16-Bit Bus Switch W/25 Ohm Resistor (FCT16245 Pinout)
PI5C16225C Low Capacitance 12-bit-to-24-bit Mux/demux Bus Switch
PI5C16226C Low Capacitance 12-bit to 24-bit Mux/demux Busswitch
PI5C162292 24-bit Mux/demux Bus Switch
PI5C16233C 32:16 Mux/demux Bus Switch W/undershoot Protection
PI5C16234C Low Capacitance 16-bit to 32-bit Mux/demux Busswitch
PI5C16244 16-Bit Bus Switch W/25 Ohm Resistor (FCT16244 Pinout)
PI5C16245 16-Bit Bus Switch W/25 Ohm Resistor (FCT16245 Pinout)
PI5C162861 20-Bit Flow-through Bus Switch (2 Enables) W/25 Ohm Resistor
PI5C162861C 20-bit, 2-port Bus Switch
Same catergory

5962-9759401Q2A : Inverting Buffers and Drivers. ti SN54LVC540A, Octal Buffers/drivers With 3-STATE Outputs.

74AC11158 : CMOS/BiCMOS->AC/ACT Family. Quadruple 2-line to 1-line Data Selector/multiplexer.

74ACT11138D : Decoders. ti 74ACT11138, 3-Line to 8-Line Decoders/demultiplexers. Designed Specifically for High-Speed Memory Decoders and Data Transmission Systems Incorporates Three Enable Inputs to Simplify Cascading and/or Data Reception Flow-Through Architecture Optimizes PCB Layout Center-Pin VCC and GND Configurations Minimize High-Speed Switching Noise EPIC (Enhanced-Performance Implanted CMOS) 1-mm Process 650-mA Typical.

74LCX646 : LCX->Low Voltage HCMOS, 5V I/O Tolerant. CMOS Octal Bus Transceiver/register With 5V Tolerant Input And Output.

74LVCH16260A : 3.3V CMOS 12-BIT Tri-port Bus Exchanger With 5V Tolerant I/o. 3.3V CMOS 12-BIT TRI-PORT BUS EXCHANGER WITH 5 VOLT TOLERANT I/O AND BUS-HOLD Typical tSK(o) (Output Skew) < 250ps ESD > 2000V per MIL-STD-883, Method > 200V using machine model = 0) VCC 0.3V, Normal Range VCC to 3.6V, Extended Range CMOS power levels (0.4 W typ. static) All inputs, outputs, and I/O are 5V tolerant Supports hot insertion.

AZ100EL16 : Bipolar->ECL 100 Family. Differential Receiver. 250ps Propagation Delay High Bandwidth Output Transitions 75k Internal Input Pulldown Resistors Direct Replacement for ON Semiconductor & MC100EL16 PACKAGE AVAILABILITY PACKAGE SOIC 8 SOIC 8 T&R SOIC 8 T&R SOIC 8 SOIC 8 T&R SOIC 8 T&R TSSOP 8 TSSOP 8 T&R TSSOP 8 T&R TSSOP 8 TSSOP 8 T&R TSSOP 8 T&R PART NO. AZ100EL16TR1 AZ100EL16TR2 MARKING AZTEL16 AZHEL16.

CD40160BF3A : ti CD40160B, CMOS Synchronous Programmable 4-Bit Decade Counter With Asynchronous Clear.

EL7156 : High Performance Pin Driver The EL7156 High Performance Pin Driver With 3-state is Suited to Many Ate And Level-shifting Applications. The 3.5A Peak Drive Capability Makes This Part an Excellent Choice When Driving High Capacitance Loads.

I74F38D : Quad 2-input NAND Buffer Open Collector. FEATURE TYPE 74F38 TYPICAL PROPAGATION DELAY 7.0ns TYPICAL SUPPLY CURRENT (TOTAL) 13mA ORDER CODE 14-pin plastic DIP 14-pin plastic SO COMMERCIAL RANGE VCC 5V 10%, Tamb N74F38N N74F38D INDUSTRIAL RANGE VCC 5V 10%, Tamb I74F38N I74F38D PKG DWG SOT27-1 SOT108-1 PINS Dna, Dnb Qn Data inputs Data output 74F (U.L.) HIGH/LOW 1.0/2.0 OC/106.7 LOAD VALUE.

IDTQ74FCT4X32H374A : CMOS/BiCMOS->FCT/FCT-T Family. 3.3v CMOS 32-bit Register With Bus Hold in Millipaq (tm).

MC74HC16XAD : Presettable Counters. The MC74HC161A and HC163A are identical in pinout to the LS161 and LS163. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. The HC161A and HC163A are programmable 4bit binary counters with asynchronous and synchronous reset, respectively. Output Drive Capability: 10 LSTTL Loads.

MD82C85 : CMOS Static Clock Controller/generator. The Intersil 82C85 Static CMOS Clock Controller/Generator provides complete control of static CMOS system operating modes and supports full speed, slow, stop-clock and stop-oscillator operation. While directly compatible with the Intersil 80C86 and 80C88 16-bit Static CMOS Microprocessor Family, the 82C85 can also be used for general system clock control.

NC7WZ04 : CMOS/BiCMOS->4000 Family. Tinylogic Uhs Dual Inverter. The is a dual inverter from Fairchild's Ultra High Speed Series of TinyLogic in the space saving SC70 6-lead package. The device is fabricated with advanced CMOS technology to achieve ultra high speed with high output drive while maintaining low static power dissipation over a very broad VCC operating range. The device is specified to operate over the to 5.5V.

SN54ALS253 : Multiplexers. 3-State Versions of the ALS153 and SN74AS153 Permits Multiplexing From n Lines to One Line Performs Parallel-to-Serial Conversion Package Options Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 300-mil DIPs These data selectors/multiplexers contain inverters and drivers to supply full.

SN74AHCT1G04 : CMOS/BiCMOS->HC/HCT Family. Single Inverter Gate. Operating Range 5.5 V Max tpd 5 V Low Power Consumption, 10-A Max ICC 8-mA Output Drive 5 V Inputs Are TTL-Voltage Compatible Latch-Up Performance Exceeds 250 mA Per JESD 17 The SN74AHCT1G04 contains one gate. The device performs the Boolean function = A. ORDERING INFORMATION TA PACKAGE 23) DBV SOT (SOT to 85C SOT (SC-70) (SC 70) DCK Reel of 3000.

SN74ALVCH162831 : Bus Oriented Circuits. 1-bit to 4-bit Address Register/driver With 3-state Outputs.

SN74S133 : Bipolar->TTL Family. 13-input Positive NAND Gate. PRODUCTION DATA information is current as of publication date. Products conform to s per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. .

XMT5170-622 : 622 Mb/s Logic Interface DFB Laser Transmitter. 622 Mb/s Logic Interface DFB Laser Transmitter Preliminary Technical Data SONET/SDH Compliant to +85C Operation Compact 20 Pin Package ECL/PECL Logic Interface Multisourced Pinout an ECL/PECL logic interface for 622 MBd transmission. The transmitter incorporates several which simplify system design. The XMT5170-622 may be operated with either 5 V power.

I74F08D,112 : F/FAST SERIES, QUAD 2-INPUT AND GATE, PDSO14. s: Gate Type: AND ; Supply Voltage: 5V ; Logic Family: TTL ; Inputs: 2 ; Propagation Delay: 6.6 ns ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Pin Count: 14 ; IC Package Type: Other, PLASTIC, SOT-108-1, SO-14.

74LV273PWDH-T : LV/LV-A/LVX/H SERIES, POSITIVE EDGE TRIGGERED D FLIP-FLOP, TRUE OUTPUT, PDSO20. s: Flip-Flop Type: D ; Triggering: Positive-edge Triggered ; Supply Voltage: 3.3V ; Output Characteristics: TRUE ; Propagation Delay: 24 ns ; fMAX: 20 MHz ; Operating Temperature: -40 to 125 C (-40 to 257 F) ; Logic Family: CMOS ; Number of Pins: 20.

 
0-C     D-L     M-R     S-Z