Details, datasheet, quote on part number: PI5C162210
CategoryLogic => Bus Interface => Bus Oriented Circuits
TitleBus Oriented Circuits
Description20-bit, 2-port Bus Switch
CompanyPericom Semiconductor Corporation
DatasheetDownload PI5C162210 datasheet


Features, Applications

Near-zero propagation delay 5 Ohm switches connect inputs to outputs Direct bus connection when switches are ON 32X384 function with flow through pinout make board layout easier Ultra-low quiescent power (0.5W typical) ideally suited for notebook applications Industrial operating temperature: to +85C Packages available: 48-pin 150-mil wide plastic BQSOP (B) 48-pin 173-mil wide plastic TVSOP (K) 48-pin 240-mil wide plastic TSSOP (A) 48-pin 300-mil wide plastic SSOP (V)

Pericom Semiconductor's PI5C series of BusSwitch circuits are produced in the Company's advanced sub-micron CMOS technology, achieving industry leading speed. The PI5C16210 is configured 20-bit, 2-port bus switches designed with a low ON resistance (5 Ohm) allowing inputs to be connected directly to outputs. The bus switch creates no additional propagational delay or additional ground bounce noise. The switches are turned ON by the Bus Enable (xOE) input signal.

Pin Name - 2B10 Description Bus Enable Inputs (Active LOW) Bus A Bus B
Note: H = High Voltage Level L = Low Voltage Level Hi-Z = High Impedance

(Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature.................................................................. to +150C Ambient Temperature with Power Applied................................. to +85C Supply Voltage to Ground Potential (Inputs & Vcc Only)........... to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only)....... +7.0V DC Input Voltage......................................................................... +7.0V DC Output Current................................................................................... 120 mA Power Dissipation......................................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

Parameters Description VIH VIL II Input HIGH Voltage Input LOW Voltage Input Current Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = 5.5V., VIN 5.5V OR GND VCC = 0V, VIN = VCC IOZH VIK V IOS VH RON High Impedance Output Current Clamp Diode Voltage Short Circuit Current(3) Input Hysteresis at Control Pins Switch On Resistance

Parameters(5) CIN COFF Description Input Capacitance A/B Capacitance, Switch Off Test Conditions VIN or 3V VIN or 3V Typ 4.5 5.5 Units pF

Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 25C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. 5. This parameter is determined by device characterization but is not production tested.

Parameters Description ICC ICCD Quiescent Power Supply Current Supply Current per Input @ TTL HIGH Supply Current per Input per MHz(4) Test Conditions(1) VCC = Max. VCC = Max. VCC = Max., A and B Pins Open Control Input Toggling 50% Duty Cycle VIN = GND or VCC VIN = 3.4V(3) Min. Typ(2) 0.1 Max. 2.5 0.25 Units A mA mA/ MHz

Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at Vcc 5.0V, +25C ambient. 3. Per TTL driven input (VIN = 3.4V, control inputs only); A and B pins do not contribute to Icc. 4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant or DC currents as they transition. This parameter is not tested, but is guaranteed by design.

Notes: 1. See test circuit and wave forms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order 0.25 ns for 50 pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.


Related products with the same datasheet
Some Part number from the same manufacture Pericom Semiconductor Corporation
PI5C162210A 20-bit, 2-port Bus Switch
PI5C162212 24-bit Bus Exchange Switch
PI5C162214 12-bit, 3-to-1 Bus-select Switch
PI5C162215CA 20-bit,hot Insertion,bus Switch With Precharged Outputs & Undershoot Protection
PI5C162244 16-Bit Bus Switch W/25 Ohm Resistor (FCT16244 Pinout)
PI5C162245 16-Bit Bus Switch W/25 Ohm Resistor (FCT16245 Pinout)
PI5C16225C Low Capacitance 12-bit-to-24-bit Mux/demux Bus Switch
PI5C16226C Low Capacitance 12-bit to 24-bit Mux/demux Busswitch
PI5C162292 24-bit Mux/demux Bus Switch
PI5C16233C 32:16 Mux/demux Bus Switch W/undershoot Protection
PI5C16234C Low Capacitance 16-bit to 32-bit Mux/demux Busswitch
PI5C16244 16-Bit Bus Switch W/25 Ohm Resistor (FCT16244 Pinout)
PI5C16245 16-Bit Bus Switch W/25 Ohm Resistor (FCT16245 Pinout)
PI5C162861 20-Bit Flow-through Bus Switch (2 Enables) W/25 Ohm Resistor
PI5C162861C 20-bit, 2-port Bus Switch
PI5C162861V 20-Bit Flow-through Bus Switch (2 Enables) W/25 Ohm Resistor
PI5C162862CA 20-bit,2-port Bus Switch With Undershoot Protection

PS396CAI : 17V Precision 16-Ch., Mux

PI74FCT574CTL : Fast CMOS Octal D Registers (3-state)

PI2PCIE2412ZHEX : Enhanced, 1.8v, PCI Express Compliant, 4-differential Channel, 2:1 Mux/demux Switch, w/ Single Enable

PI49FCT806ATSE : FCT SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16 Specifications: Device Type: Clock Driver ; Bus Interface: CMOS ; Package Type: Surface Mount, QSOP, 0.150 INCH, QSOP-16 ; Supply Voltage: 4.75 to 5.25 volts ; Skew: 800 ps ; Operating Temperature: 0.0 to 70 C (32 to 158 F) ; Features / Standards: RoHS, Lead-Free

PI6C41201L : 6C SERIES, LOW SKEW CLOCK DRIVER, 1 TRUE OUTPUT(S), 1 INVERTED OUTPUT(S), PDSO8 Specifications: Device Type: Clock Driver ; Package Type: Surface Mount, TSSOP, 0.173 INCH, TSSOP-8 ; Supply Voltage: 3.14 to 3.46 volts ; Skew: 30 ps ; Operating Temperature: 0.0 to 70 C (32 to 158 F)

PI74FCT2574CTRX : FCT SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, PDSO16 Specifications: Counter Type: BINARY COUNTER ; Counter Category: Synchronous ; Counter Direction: UP ; Supply Voltage: 5V, 5.25 ; Package Type: 0.150 INCH, PLASTIC, QSOP-16 ; Logic Family: CMOS, FCT ; Number of Pins: 16 ; Number of Stages (Bits): 4 bits ; Operating Temperature: -40 to 85 C (-40 to 1

PI74FCT648DTSX : FCT SERIES, 8-BIT TRANSCEIVER, INVERTED OUTPUT, PDSO20 Specifications: Technology: CMOS ; Device Type: Transceiver ; Supply Voltage: 5V ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Package Type: TSSOP, 0.173 INCH, PLASTIC, TSSOP-20 ; Pins: 20

PI74PLT244QE : LPT SERIES, DUAL 4-BIT DRIVER, INVERTED OUTPUT, PDSO20 Specifications: Technology: CMOS ; Device Type: Line / Bus Driver ; Supply Voltage: 3.3V ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Package Type: TSSOP, 0.173 INCH, PLASTIC, TSSOP-20 ; Pins: 20

PT7M8202B29ZEE : 1.2 V FIXED POSITIVE LDO REGULATOR, PDSO5 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: SC-70, Other, GREEM, SC-70, 5 PIN ; Life Cycle Stage: ACTIVE ; Output Voltage: 1.18 to 1.22 volts ; IOUT: 0.3000 amps ; VIN: 1.8 to 5.5 volts

Same catergory

5962-9754901QKA : D-Type (3-State) Flip-Flops. ti SN54AS575, Octal D-type Edge-triggered Flip-flops With 3-State Outputs.

74ACT11010D : ti 74ACT11010, Triple 3-Input Positive-nand Gates. Inputs Are TTL-Voltage Compatible Flow-Through Architecture to Optimize PCB Layout Center-Pin VCC and GND Configurations Minimize High-Speed Switching Noise EPIC t (Enhanced-Performance Implanted CMOS) 1-mm Process 500-mA Typical Latch-Up Immunity at 125C Package Options Include Plastic Small-Outline Packages, Ceramic Chip Carriers, and Standard Plastic.

74ACT11132 : CMOS/BiCMOS->AC/ACT Family. Quadruple Positive-nand Gate With Schmitt-trigger Inputs.

CDC2509BPW : 3.3-v Phase-lock Loop Clock Driver. Designed to Meet PC SDRAM Registered DIMM Spread Spectrum Clock Compatible Operating Frequency 25 MHz to 125 MHz tPhase Error Minus Jitter to 100 MHz 150 ps Jitter (pk pk) at 66 MHz to 100 MHz 80 ps Jitter (cyc cyc) at 66 MHz to 100 MHz is |100 ps| Available in Plastic 24-Pin TSSOP Phase-Lock Loop Clock Distribution for Synchronous DRAM Applications.

IDT74LVC16374A : CMOS/BiCMOS->LVC/ALVC/VCX Family->Low Voltage. 3.3v CMOS 16-bit Edge-triggered D-type Flip-flop With 3-state Outputs, 5v Tolerant I/o.

IN74ACT640DW : Octal Bus Transceiver (3-State) 20. The IN74ACT640 is identical in pinout to the LS/ALS640, HC/HCT640. The IN74ACT640 may be used as a level converter for interfacing TTL or NMOS outputs to High Speed CMOS inputs. The a 3-state transceiver that is used for 2-way asynchronous communication between data buses. The device has an active-low Output Enable pin, which is used to place the I/O ports.

JM38510/65704BRA : Inverting Buffers and Drivers. ti SN54HC241, Octal Buffers And Line Drivers With 3-State Outputs.

MC74AC02D : Quad 2-Input NOR GATE, Package: Soic, Pins=14. Figure 1. Pinout: 14Lead Packages Conductors (Top View) MAXIMUM RATINGS* Symbol VCC Vin Vout Iin Iout ICC Tstg Parameter DC Supply Voltage (Referenced to GND) DC Input Voltage (Referenced to GND) DC Output Voltage (Referenced to GND) DC Input Current, per Pin DC Output Sink/Source Current, per Pin DC VCC or GND Current per Output Pin Storage Temperature.

MC74HC00AFEL : 2-Input NAND Gate, Package: SOEIAJ-14, Pins=14. The MC74HC00A is identical in pinout to the LS00. The device inputs are compatible with Standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. Output Drive Capability: 10 LSTTL Loads Outputs Directly Interface to CMOS, NMOS and TTL Operating Voltage Range: to 6V Low Input Current: 1A High Noise Immunity Characteristic.

NC7NZ17 : Tinylogic Uhs Triple Buffer With Schmitt Trigger Inputs.

SN5427W : Triple 3-input Positive-nOR GATEs.

SN54AHC244 : Bus Oriented Circuits. Octal Buffers/drivers With 3-state Outputs. Operating Range to 5.5-V VCC Latch-Up Performance Exceeds 250 mA Per JESD 17 These octal buffers/drivers are designed specifically to improve the performance and density of 3-state memory-address drivers, clock drivers, and bus-oriented receivers and transmitters. The 'AHC244 devices are organized as two 4-bit buffers/line drivers with separate output-enable.

SN54LS629 : . PRODUCTION DATA information is current as of publication date. Products conform to s per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. .

SN54LV540A : Octal Buffers/drivers With 3-state Outputs. The 'LV540A devices are octal buffers/drivers designed for to 5.5-V VCC operation. These devices are ideal for driving bus lines or buffer memory address registers. They feature inputs and outputs on opposite sides of the package to facilitate printed circuit board layout. The 3-state control gate is a two-input AND gate with active-low inputs so that.

SN74AHCT132DB : Quadruple Positive-nand Gates With Schmitt-trigger Inputs. SN54AHCT132, SN74AHCT132 QUADRUPLE POSITIVE-NAND GATES WITH SCHMITT-TRIGGER INPUTS These devices perform the Boolean function or in positive logic. Each circuit functions as a NAND gate, but because of the Schmitt action, it has different input threshold levels for positive- and negative-going signals. These circuits are temperature compensated and can be triggered.

SN74ALVTH16240 : Bus Oriented Circuits. 2.5-v/3.3v 16-bit Buffers/drivers With 3-state Outputs.

SN74F190AN : ti SN74F190A, Synchronous Up/down Decade Counters. SN74F190A SYNCHRONOUS 4-BIT UP/DOWN DECADE COUNTER WITH RESET AND RIPPLE CLOCK High-Speed fmax of 125 MHz Typical Single Down/Up Count Control Line Look-Ahead Circuitry Enhances Speed of Cascaded Counters Fully Synchronous in Count Modes Asynchronously Presettable With Load Control Package Options Include Plastic Small-Outline Packages and Standard.

TC7MET541AFK : VHCT Equivalent. Function = Octal Bus Buffer Non-inverted, 3-state Outputs ;; = High: TPD = 5.4 NS (typ.) (VCC = 5 V) Low: Icc = 4 a (max.

0-C     D-L     M-R     S-Z