Details, datasheet, quote on part number: PI5C162214
PartPI5C162214
CategoryLogic => Bus Interface
Description12-bit, 3-to-1 Bus-select Switch
CompanyPericom Semiconductor Corporation
DatasheetDownload PI5C162214 datasheet
  

 

Features, Applications

Features

Near-zero propagation delay 5 switches connect inputs to outputs Direct bus connection when switches are ON Ultra-low quiescent power (0.2µA typical) ­ ideally suited for notebook applications Industrial operating temperature: to +85°C Packages available: 56-pin 240-mil wide plastic TSSOP (A) 56-pin 300-mil wide plastic SSOP (V)

Pericom Semiconductors PI5C series of BusSwitch circuits are produced in the Companys advanced 0.8 micron CMOS technology, achieving industry leading speed. The PI5C16214 and PI5C162214 are 3-to-1 bus-select switches designed with a low ON resistance (5) allowing inputs to be connected directly to outputs. These devices operate as 12-bit bus switches via the data select pins (S0-S2). The PI5C162214 device has a built-in 25-ohm series resistor to reduce noise resulting from reflections, thus eliminating the need for an external terminating resistor.

Note: H = High Voltage Level L = Low Voltage Level Z = High Impedance

(Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature............................................................ to +150°C Ambient Temperature with Power Applied........................... to +85°C Supply Voltage to Ground Potential (Inputs & Vcc Only)..... to +7.0V Supply Voltage to Ground Potential (Outputs & D/O Only).. +7.0V DC Input Voltage.................................................................... +7.0V DC Output Current............................................................................... 120mA Power Dissipation.................................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.

Parameters Description VIH VIL II Input HIGH Voltage Input LOW Voltage Input Current Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = 5.5V., VIN 5.5V OR GND VCC = 0V, VIN = VCC IOZH VIK IOS VH RON High Impedance Output Current Clamp Diode Voltage Short Circuit Current

Input Hysteresis at Control Pins Switch On Resistance

Parameters(5) CIN COFF Description Input Capacitance A/B Capacitance, Switch Off Test Conditions VIN or 3V VIN or 3V Typ 4.5 5.5 Units pF

Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. 5. This parameter is determined by device characterization but is not production tested.

Parameters Description ICC ICCD Quiescent Power Supply Current Supply Current per Input @ TTL HIGH Supply Current per Input per MHz(4) Test Conditions(1) VCC = Max. VCC = Max. VCC = Max., A and B Pins Open Control Input Toggling 50% Duty Cycle VIN = GND or VCC VIN = 3.4V(3) Min. Typ(2) 0.1 Max. 2.5 0.25 Units µA mA mA/ MHz

Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at Vcc 5.0V, +25°C ambient. 3. Per TTL driven input (VIN = 3.4V, control inputs only); A and B pins do not contribute to Icc. 4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant or DC currents as they transition. This parameter is not tested, but is guaranteed by design.

PI5C16214 Vcc 5V ±0.5V Parameters tPLH tPHL tPZH tPZL tPHZ tPLZ Description Propagation Ax to Bx, to Ax Bus Enable Time XOE or Bx Bus Disable Time XOE 50pF RL Min. Max. 5.5 ns Units

PI5C162214 Vcc 5V ±0.5V Parameters tPLH tPHL tPZH tPZL tPHZ tPLZ Description Propagation Ax to Bx, to Ax Bus Enable Time XOE or Bx Bus Disable Time XOE 50pF RL Min. Max. 5.5 ns Units

Notes: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. Pericom Semiconductor Corporation 2380 Bering Drive San Jose, 95131 1-800-435-2336 Fax (408) 435-1100 http://www.pericom.com


 

Related products with the same datasheet
PI5C162214A
PI5C162214V
Some Part number from the same manufacture Pericom Semiconductor Corporation
PI5C162214A 12-bit, 3-to-1 Bus-select Switch
PI5C162215CA 20-bit,hot Insertion,bus Switch With Precharged Outputs & Undershoot Protection
PI5C162215CB
PI5C162244 16-Bit Bus Switch W/25 Ohm Resistor (FCT16244 Pinout)
PI5C162245 16-Bit Bus Switch W/25 Ohm Resistor (FCT16245 Pinout)
PI5C16225C Low Capacitance 12-bit-to-24-bit Mux/demux Bus Switch
PI5C16226C Low Capacitance 12-bit to 24-bit Mux/demux Busswitch
PI5C162292 24-bit Mux/demux Bus Switch
PI5C16233C 32:16 Mux/demux Bus Switch W/undershoot Protection
PI5C16234C Low Capacitance 16-bit to 32-bit Mux/demux Busswitch
PI5C16244 16-Bit Bus Switch W/25 Ohm Resistor (FCT16244 Pinout)
PI5C16245 16-Bit Bus Switch W/25 Ohm Resistor (FCT16245 Pinout)
PI5C162861 20-Bit Flow-through Bus Switch (2 Enables) W/25 Ohm Resistor
PI5C162861C 20-bit, 2-port Bus Switch
PI5C162861V 20-Bit Flow-through Bus Switch (2 Enables) W/25 Ohm Resistor
PI5C162862CA 20-bit,2-port Bus Switch With Undershoot Protection
PI5C162862CB
PI5C16292 24:12-Bit, Mux/demux Bus Switch W/500 Ohm Pull-down
PI5C16861 20-Bit Flow-through Bus Switch (2 Enables) W/25 Ohm Resistor
PI5C16861C 20-bit, 2-port Bus Switch
PI5C16861V 20-Bit Flow-through Bus Switch (2 Enables) W/25 Ohm Resistor
Same catergory

54LVX3384 : 10-bit Low Power Bus Switch. The 54LVX3384 provides 10 bits of high-speed CMOS TTL-compatible bus switches. The low on resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. The device is organized as two 5-bit switches with separate bus enable (OE ) signals. When OE is low, the switch is on and port.

5962-9172601M3A : ti SN54BCT8244A, Scan Test Devices With Octal Buffers. SN54BCT8244A, SN74BCT8244A SCAN TEST DEVICES WITH OCTAL BUFFERS Members of the Texas Instruments SCOPE TM Family of Testability Products Octal Test-Integrated Circuits Functionally Equivalent to 'F244 and 'BCT244 in the Normal-Function Mode Compatible With the IEEE Standard 1149.1-1990 (JTAG) Test Access Port and Boundary-Scan Architecture Test Operation.

74LX1G70 : LCX Low Voltage HCMOS. Low Voltage Single Buffer. 5V TOLERANT INPUTS HIGH SPEED: tPD = 4.2ns (MAX.) at VCC = 3V LOW POWER DISSIPATION: ICC = 1µA (MAX.) = 25°C POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24mA (MIN) at VCC = 3V BALANCED PROPAGATION DELAYS: tPLH tPHL OPERATING VOLTAGE RANGE: VCC(OPR) 5.5V (1.2V Data Retention) IMPROVED LATCH-UP IMMUNITY The is an advanced.

74VHCT132A : VHC/VHCT->Low Noise HCMOS. Quad 2-INPUT Schmitt NAND Gate. HIGH SPEED: tPD 6.5 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC 2 µA (MAX.) at TA=25°C TYPICAL HYSTERESIS 0.7V at VCC = 4.5V POWER DOWN PROTECTION ON INPUTS & OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL 8 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH tPHL OPERATING VOLTAGE RANGE: VCC(OPR) to 5.5V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 132 IMPROVED.

CD4012B : CMOS/BiCMOS->4000 Family. CMOS NAND Gates. Data sheet acquired from Harris Semiconductor SCHS021B ­ Revised May 2002 The CD4011B, CD4012B, and CD4023B types are supplied in 14-lead hermetic dual-in-line ceramic packages (D and F suffixes), 14-lead dual-in-line plastic packages (E suffix), 14-lead dual-in-line small-outline plastic package (M suffix), thin shrink small-outline package (PWR suffix),.

CD54HCT4511 : High-speed CMOS Logic. Data sheet acquired from Harris Semiconductor SCHS279 This data sheet is applicable to the CD54HC4511 and CD74HCT4511. The CD54HCT4511 was not acquired from Harris Semiconductor. See SCHS214 for information on the CD74HCT4511. .

HD74HC195 : 4-bit Parallel-access Shift Register. Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp. The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog and discrete devices, and memory chips.

HEF4068B : HEF4068B Gates; 8-input NAND Gate;; Package: SOT108-1 (SO14), SOT27-1 (DIP14).

HEF4085BD : Dual 2-wide 2-input And-or-invert Gate. For a complete data sheet, please also download: The IC04 LOCMOS HE4000B Logic Family s HEF, HEC The IC04 LOCMOS HE4000B Logic Package Outlines/Information HEF, HEC Product File under Integrated Circuits, IC04 January 1995 The is a dual 2-wide 2-input AND-OR-invert gate, each with an additional input or B4) which can be used as either an expander input.

IDT74ALVCH16282 : Low Voltage CMOS/BiCMOS->LVC/ALVC/VCX Family. 3.3v CMOS 18-bit to 36-bit Registered Bus Exchanger With 3-state Outputs And Bus-hold.

MC10164N : 8-line Multiplexer. The is a high speed, low power eight­channel data selector which routes data present at one­of­eight inputs to the output. The data is routed according to the three bit code present on the address inputs. An enable input is provided for easy bit expansion. L SUFFIX CERAMIC PACKAGE CASE 620­10 P SUFFIX PLASTIC PACKAGE CASE 648­08 FN SUFFIX PLCC CASE.

SN54ABTH182502A : Bus Oriented Circuits. Scan Test Devices With 18-bit Universal Bus Transceivers.

SN74157N : Multiplexers. ti SN74157, Quad 2-line to 1-line Data Selectors / Multiplexers.

SN74LVC16245DL : Standard Transceivers. ti SN74LVC16245, 16-Bit Bus Transceiver With 3-State Outputs.

SN74LVC1G240DBVR : Single Gates. ti SN74LVC1G240, Single Buffer/driver With 3-State Outputs.

TC74LVX08F : Quad 2-input And Gate.

TPIC6B273 : Bipolar->TTL Family. Power Logic Octal D-type Latch. Low rDS(on). 5 Typical Avalanche Energy. 30 mJ Eight Power DMOS-Transistor Outputs of 150-mA Continuous Current 500-mA Typical Current-Limiting Capability Output Clamp Voltage. 50 V Low Power Consumption The is a monolithic, high-voltage, medium-current, power logic octal D-type latch with DMOS-transistor outputs designed for use in systems that require.

A3P060-2VQ100Y : FPGA, 1536 CLBS, 60000 GATES, PQFP100. s: System Gates: 60000 ; Logic Cells / Logic Blocks: 1536 ; Package Type: TQFP, Other, 14 X 14 MM, 1 MM HEIGHT, 0.50 MM PITCH, VTQFP-100 ; Logic Family: CMOS ; Pins: 100 ; Operating Temperature: 0 to 70 C (32 to 158 F) ; Supply Voltage: 1.5V.

74AHC32BQ : AHC SERIES, QUAD 2-INPUT OR GATE, PQCC14. s: Gate Type: OR ; Supply Voltage: 5V ; Logic Family: CMOS ; Inputs: 2 ; Propagation Delay: 14.5 ns ; Operating Temperature: -40 to 125 C (-40 to 257 F) ; Pin Count: 14 ; IC Package Type: Other, 2.50 X 3 MM, 0.85 MM HEIGHT, PLASTIC, MO-241, SOT-762-1, DHVQFN-14.

 
0-C     D-L     M-R     S-Z