· High-performance, low-cost solution to switch between video sources· Wide bandwidth: 150 MHz· Low ON-resistance: 3ohm· Low crosstalk at 10 MHz: ­58dB· Ultra-low quiescent power (0.1µA typical)· Single supply operation: +5.0V· Fast switching: 10ns· High-current output: 100mA· Packages available: 16-pin 150-mil-wide plastic QSOP (Q) 16-pin 150-mil-wide plastic SOIC (W)· Functionally equivalent to QS4A210

Pericom Semiconductor's PI5V series of mixed signal video circuits are produced using the Company's advanced CMOS low power technology achieving industry leading performance. The is a true bidirectional Dual 4-channel multiplexer/ demultiplexer that is recommended for both S-Video or composite video switching applications. The VideoSwitchTM can be driven from a current output RAMDAC or voltage output composite video source. Low ON-resistance and wide bandwidth make it ideal for video and other applications. Also this device has exceptionally high current capability which is far greater than most analog switches offered today. A single 5V supply is all that is required for operation. The PI5V331 offers a high-performance, low-cost solution to switch between video sources.

Description Analog Video I/O (Usually Inputs) Select Input Enable Analog Video I/O (Usually Outputs) Ground Power

PI5V331 Low ON-Resistance Wideband Video Dual 4-Channel Mux/Demux 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Maximum Ratings

(Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature........................................................... to +150°C Note: Stresses greater than those listed under MAXIMUM Ambient Temperature with Power Applied.......................... to +85°C RATINGS may cause permanent damage to the deSupply Voltage to Ground Potential (Inputs & Vcc Only)... to +7.0V vice. This is a stress rating only and functional operaSupply Voltage to Ground Potential (Outputs & D/O Only) to +7.0V tion of the device at these or any other conditions above those indicated in the operational sections of DC Input Voltage.................................................................. to +7.0V this specification is not implied. Exposure to absolute DC Output Current............................................................................ 120 mA maximum rating conditions for extended periods may Power Dissipation................................................................................... 0.5W affect reliability.

Parameters Description VANALOG Analog Signal Range VIH VIL IIH IIL IO VIK IOS VH RON Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current Analog Output Leakage Current Clamp Diode Voltage Short Circuit Current

Test Conditions(1) Guaranteed Logic HIGH Level Guaranteed Logic LOW Level VCC = Max., VIN = VCC = Max., VIN = GND or D VCC, Switch Off VCC = Min., IIN = 0V VCC = Min., VOUT = 75ohm, ION 13 mA VCC = MIN., VOUT = 75ohm, ION 26 mA

Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between S1, S2, and D I/O pins at indicated current through the switch. ON resistance is determined by the lower of the voltages on the S1, S2, and D I/O pins. VOUT is the voltage across RL.

PI5V331 Low ON-Resistance Wideband Video Dual 4-Channel Mux/Demux 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Dynamic Characteristics (Over the Operating Range, to +85°C, VCC 5V ±5%)

Parameter Description Turn On Time Turn Off Time ­3 dB Bandwidth Crosstalk Differential Gain Differential Phase

Test Conditions = 20 pF, see Fig. = 20 pF, see Fig. = 150ohm, see Fig. 3 RIN 150ohm, 10 MHz, see Fig. = 3.58 MHz, see Fig. = 3.58 MHz, see Fig. 1 VIN = 1 MHz VIN = 1 MHz VIN = 1 MHz 150ohm, 10 MHz, see Fig. 3

Parameters Description ICC ICCD Quiescent Power Supply Current Supply Current per Input @ TTL HIGH Supply Current per Input per MHz(4) Test Conditions(1) VCC = Max. VCC = Max. VCC = Max., S1, S2, and D Pins Open EN = GND Control Input Toggling 50% Duty Cycle IN = GND or VCC = 3.4V(3) Min. Typ(2) 0.1 Max. 2.5 0.25 Units µA mA mA/ MHz

Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at Vcc 5.0V, +25°C ambient. 3. Per TTL driven input (VIN = 3.4V, control inputs only); S1, S2, and D pins do not contribute to Icc. 4. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The S1, S2, and D I/O pins generate no significant or DC currents as they transition. This parameter is not tested, but is guaranteed by design.