|
|
Part: LPC2114FBD64
Category:
Microcontrollers
-> 16/32 bit
Description: Single-chip 16/32-bit Microcontrollers; 128/256 KB Isp/iap Flash With 10-bit ADC<<<>>>the LPC2114/LPC2124 Are Based on a 16/32 Bit ARM7TDMI-STM Cpu With Real-time Emulation And Embedded Trace Support, Together With 128/256 Kilobytes (kB) of Embedded High Speed Flash Memory. A 128-bit Wide Memory Interface And a Unique Accelerator Architecture Enable 32-bit Code Execution at Maximum Clock Rate. For Critical Code Size Applications, The Alternative 16-bit Thumb Mode Reduces Code BY More Than 30pct With Minimal Performance Penalty. <<<>>><<<>>>With TheIR Compact 64 Pin Package, Low Power Consumption, Various 32-bit Timers, 4-channel 10-bit ADC, PWM Channels And 46 Gpio Lines With up to 9 External Interrupt Pins These Microcontrollers Are Particularly Suitable For Industrial Control, Medical Systems, Access Control And Point-of-sale. With a Wide Range of Serial Communications Interfaces, They Are Also Very Well Suited For Communication Gateways, Protocol Converters And Embedded Soft Modems as Well as Many Other General-purpose Applications. <<<>>><<<>>> <<<>>> Features Key Features<<<>>>16/32-bit ARM7TDMI-S Microcontroller in a Tiny LQFP64 Package. <<<>>>16 KB On-chip Static RAM. <<<>>>128/256 KB On-chip Flash Program Memory. 128-bit Wide Interface/accelerator Enables High Speed 60 MHZ Operation. <<<>>>In-System Programming (ISP) And In-application Programming (IAP) Via On-chip Boot-loader Software. Flash Programming Takes 1 MS Per 512 Byte Line. Single Sector or Full Chip Erase Takes 400 Ms. <<<>>>EmbeddedICE-RT Interface Enables Breakpoints And Watch Points. Interrupt Service Routines CAN Continue to Execute Whilst The Foreground Task is Debugged With The On-chip Realmonitor Software. <<<>>>Embedded Trace Macrocell Enables Non-intrusive High Speed Real-time Tracing of Instruction Execution. <<<>>>Four Channel 10-bit A/D Converter With Conversion Time as Low as 2.44 Us. <<<>>>Two 32-bit Timers (with 4 Capture And 4 Compare Channels), PWM Unit (6 Outputs), Real Time Clock And Watchdog. <<<>>>Multiple Serial Interfaces Including Two Uarts (16C550), Fast i C (400 Kbits/s) And Two Spistm. <<<>>>60 MHZ Maximum Cpu Clock Available From Programmable On-chip Phase-locked Loop. <<<>>>Vectored Interrupt Controller With Configurable Priorities And Vector Addresses. <<<>>>Up to Forty-six 5 V Tolerant General Purpose I/o Pins. Up to 9 Edge or Level Sensitive External Interrupt Pins Available. <<<>>>On-chip Crystal Oscillator With an Operating Range of 1 MHZ to 30 Mhz. <<<>>>Two Low Power Modes, Idle And Power-down. <<<>>>Processor Wake-up From Power-down Mode Via External Interrupt. <<<>>>Individual Enable/disable of Peripheral Functions For Power Optimization. <<<>>>Dual Power Supply: <<<>>>CPU Operating Voltage Range of 1.65 V to 1.95 V (1.8 V +-0.15 V). <<<>>>I/O Power Supply Range of 3.0 V to 3.6 V (3.3 V +-10pct) With 5 V Tolerant I/o Pads.16/32-bit ARM7TDMI-S Processor.
Company: Philips Semiconductors
Datasheet: Download LPC2114FBD64 datasheet File size : 165 kB
Request For quote: Find where to buy LPC2114FBD64
Datasheet text preview:
LPC2114/LPC2124
Single-chip 16/32-bit microcontrollers; 128/256 kB ISP/IAP Flash with 10-bit ADC
Rev. 02 -- 02 February 2004 Preliminary data
1. General description
The LPC2114/LPC2124 are based on a 16/32 bit ARM7TDMI-STM CPU with real-time emulation and embedded trace support, together with 128/256 kilobytes (kB) of embedded high speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at maximum clock rate. For critical code size applications, the alternative 16-bit Thumb Mode reduces code by more than 30% with minimal performance penalty. With their compact 64 pin package, low power consumption, various 32-bit timers, 4-channel 10-bit ADC, PWM channels and 46 GPIO lines with up to 9 external interrupt pins these microcontrollers are particularly suitable for industrial control, medical systems, access control and point-of-sale. With a wide range of serial communications interfaces, they are also very well suited for communication gateways, protocol converters and embedded soft modems as well as many other general-pur pose applications.
2. Features
2.1 Key features
s 16/32-bit ARM7TDMI-S microcontroller in a tiny LQFP64 package. s 16 kB on-chip Static RAM. s 128/256 kB on-chip Flash Program Memory. 128-bit wide interface/accelerator enables high speed 60 MHz operation. s In-System Programming (ISP) and In-Application Programming (IAP) via on-chip boot-loader software. Flash programming takes 1 ms per 512 byte line. Single sector or full chip erase takes 400 ms. s EmbeddedICE-RT interface enables breakpoints and watch points. Interrupt ser vice routines can continue to execute whilst the foreground task is debugged with the on-chip RealMonitor software. s Embedded Trace Macrocell enables non-intrusive high speed real-time tracing of instruction execution. s Four channel 10-bit A/D converter with conversion time as low as 2.44 µs. s Two 32-bit timers (with 4 capture and 4 compare channels), PWM unit (6 outputs), Real Time Clock and Watchdog. s Multiple serial interfaces including two UARTs (16C550), Fast I2C (400 kbits/s) and two SPIsTM. s 60 MHz maximum CPU clock available from programmable on-chip Phase-Locked Loop. s Vectored Interrupt Controller with configurable priorities and vector addresses.
Philips Semiconductors
LPC2114/LPC2124
Single-chip 16/32-bit microcontrollers
s Up to forty-six 5 V tolerant general purpose I/O pins. Up to 9 edge or level sensitive external interrupt pins available. s On-chip crystal oscillator with an operating range of 1 MHz to 30 MHz. s Two low power modes, Idle and Power-down. s Processor wake-up from Power-down mode via external interrupt. s Individual enable/disable of peripheral functions for power optimization. s Dual power supply: x CPU operating voltage range of 1.65 V to 1.95 V (1.8 V ±0.15 V). x I/O power supply range of 3.0 V to 3.6 V (3.3 V ±10%) with 5 V tolerant I/O pads.16/32-bit ARM7TDMI-S processor.
3. Ordering information
Table 1: Ordering information Package Name LPC2114FBD64 LPC2124FBD64 LQFP64 LQFP64 Description Version plastic low profile quad flat package, 64 leads, SOT314-2 body 10 × 10 × 1.4 mm plastic low profile quad flat package, 64 leads, SOT314-2 body 10 × 10 × 1.4 mm Type number
3.1 Ordering options
Table 2: Part options Flash memory 128 kB 256 kB RAM 16 kB 16 kB CAN Temperature range (°C) -40 to +85 -40 to +85 Type number LPC2114FBD64 LPC2124FBD64
9397 750 12805
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Preliminary data
Rev. 02 -- 02 February 2004
2 of 33
Philips Semiconductors
LPC2114/LPC2124
Single-chip 16/32-bit microcontrollers
4. Block diagram
TRST(1) TMS(1) TCK(1) TDI(1) TDO(1)
RT CK
XTAL1
XTAL2
RST V3 V1.8 SCL* SDA* SCK* MOSI* MISO* SSEL*
TEST/DEBUG INTERFACE
EMULATION TRACE MODULE
PLL system clock
SYSTEM FUNCTIONS
ARM7TDMI-S
AHB BRIDGE ARM7 LOCAL BUS
VECTORED INTERRUPT CONTROLLER
AMBA AHB (Advanced High-performance Bus)
INTERNAL SRAM CONTROLLER
INTERNAL FLASH CONTROLLER AHB TO VPB VPB BRIDGE DIVIDER
AHB DECODER
16 kB SRAM
128/256 kB FLASH
EINT0* EINT1* EINT2* EINT3* EXTERNAL INTERRUPTS
APB I2C SERIAL INTERFACE
8 x CAP* 8 x MAT*
CAPTURE/ COMPARE TIMER0/TIMER1
SPI SERIAL INTERFACE 0 & 1
TxD0,1* PWM1..6* PWM0 RxD0,1* UART0/UART1
MODEM CONTROL (6 PINS)*
P0 (30 PINS) P1.31:16 GENERAL PURPOSE I/O REAL TIME CLOCK
Ain3:0*
10-BIT A/D CONVERTER
WATCHDOG TIMER
SYSTEM CONTROL
*Shared with GPIO
002aaa659
(1) When test/debug interface is used, GPIO/other functions sharing these pins are not available.
Fig 1. Block diagram.
9397 750 12805 © Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Preliminary data
Rev. 02 -- 02 February 2004
VSS
3 of 33
Others parts begin by lp
LP-1 LP-2 LP-3 LP-4 LP-5 LP-6 LP-7 LP-8 LP-9 LP-10 LP-11 LP-12 LP-13 LP-14 LP-15 LP-16 LP-17 LP-18 LP-19 LP-20
|
|
|
