Details, datasheet, quote on part number: RH5RH311A-T1
PartRH5RH311A-T1
Category
DescriptionPWM Step-up Dc/dc Converter
CompanyRicoh Corporation
DatasheetDownload RH5RH311A-T1 datasheet
  

 

Features, Applications

The 2B/ 3B Series are PWM Step-up DC/DC converter ICs by CMOS process. The 1A IC consists of an oscillator, a PWM control circuit, a driver transistor (Lx switch), a reference voltage unit, an error amplifier, a phase compensation circuit, resistors for voltage detection, a soft-start circuit, and an Lx switch protection circuit. A low ripple, high efficiency step-up DC/DC converter can be constructed of this 1A IC with only three external components, that is, an inductor, a diode and a capacitor. These 2B/ 3B ICs can achieve ultra-low supply current (no load) TYP. 15A by a newly developed PWM control circuit, equivalent to the low supply current of a VFM (chopper) Step-up DC/DC converter. Furthermore, these ICs can hold down the supply current to TYP. 2A by stopping the operation of the oscillator when the input voltage > (the output voltage set value + the dropout voltage by the diode and the inductor). These 2B/ 3B Series ICs are recommendable to the user who desires a low ripple PWM DC/DC converter, but cannot adopt a conventional PWM DC/DC converter because of its too large supply current. The 2B/ 3B Series ICs use the same chip as that employed in the 1A IC and are provided with a drive pin (EXT) for an external transistor. Because of the use of the drive pin (EXT), an external transistor with a low saturation voltage can be used so that a large current can be caused to flow through the inductor and accordingly a large output current can be obtained. Therefore, these 2B/ 3B Series ICs are recommendable to the user who need a current as large as several tens mA to several hundreds mA. The 3B IC also includes an internal chip enable circuit so that it is possible to set the standby supply current at MAX. 0.5A. These 2B/ 3B ICs are suitable for use with battery-powered instruments with low noise and low supply current.

FEATURES

Small Number of External Components..........Only an inductor, a diode and a capacitor (RH5RH 1A) Low Supply Current...........................................TYP. 15A (RH5RH301A) Low Ripple and Low Noise Low Start-up Voltage (when the output current 1mA)..................MAX. 0.9V High Output Voltage Accuracy..........................2.5% High Efficiency...................................................TYP. 85% Low Temperature-Drift Coefficient of Output Voltage......................TYP. 50 ppm/C Soft-Start.............................................................MIN. 500s Small RH5RH 2B),

APPLICATIONS

Power source for battery-powered equipment. Power source for cameras, camcorders, VCRs, PDAs, electronic data banks,and hand-held communication

Power source for instruments which require low noise and low supply current, such as hand-held audio equip-

Power source for appliances which require higher cell voltage than that of batteries used in the appliances.

Lx Vss LxSW PWM control EXT OSC Chip Enable + Error Amp. VLX limiter Buffer Slow start Phase Comp. Vref OUT

Error Amp. (Error Amplifier) has a DC gain of 80dB, and Phase Comp. (Phase Compensation Circuit) provides the frequency characteristics including the 1st pole (fp=0.25Hz) and the zero point (fz=2.5kHz). Furthermore, another zero point (fz=1.0kHz) is also obtained by the resistors and a capacitor connected to the OUT pin.

In RH5RH Series, the output voltage, the driver, and the taping type for the ICs can be selected at the user's request. The selection can be made by designating the part number as shown below RH5RH Part Number b c

Description

Setting Output Voltage (VOUT): Stepwise setting with a step 0.1V in the range 7.5V is possible. Designation of Driver: 1A: Internal Lx Tr. Driver (Oscillator Frequency 50kHz) 2B: External Tr. Driver (Oscillator Frequency 100kHz) 3B: Internal Tr./External Tr. (selectively available) (Oscillator Frequency 100kHz, with chip enable function) Designation of Taping Type : Ex. T1, T2 (refer to Taping Specifications) "T1" is prescribed as a standard.

For example, the product with Output Voltage 5.0V, the External Driver (the Oscillator Frequency 100kHz) and Taping Type T1, is designated by Part Number RH5RH502B-T1.


 

Related products with the same datasheet
RH5RH311A-T2
RH5RH312B-T1
RH5RH312B-T2
RH5RH313B-T1
RH5RH313B-T2
RH5RH321A-T1
RH5RH321A-T2
RH5RH322B-T1
RH5RH322B-T2
RH5RH323B-T1
RH5RH323B-T2
RH5RH331A-T1
Some Part number from the same manufacture Ricoh Corporation
RH5RH311A-T2 PWM Step-up Dc/dc Converter
R3111E501A LOW Voltage Detector
RD5RW21AA The Rx5rw Series are Cmos-based Voltage Regulator ICs with high Accuracy Output Voltage and Ultra-low
RQ5RW50CA
RD5RW20AA
RX5VT47A LOW Voltage Detector
R1131D081A Low Voltage 300ma LDO Regulator
RD5RW29AA The Rx5rw Series are Cmos-based Voltage Regulator ICs with high Accuracy Output Voltage and Ultra-low
RH5RZ58CA Power Management ICs MARK Informations
R1161D201A 3-mode 300ma LDO Regulator
Same catergory

AD539JD : Wideband Dual-channel Linear Multiplier/divider.

AS2945M3 : . Output Accuracy @ 500mA Output Very Low Quiescent Current Low Dropout Voltage Extremely Tight Load And Line Regulation Very Low Temperature Coefficient Current & Thermal Limiting Error Flag Warns Of Output Dropout Logic-Controlled Electronic Shutdown Output Programmable From to 29V APPLICATIONS Battery Powered Systems Cordless Telephones Radio Control.

KMY24 : Microwave Motion Sensor. The KMY is a microwave rader motion sensor based on the Doppler effect. It transmits a low energy microwave radiation at 2.45 GHz which is reflected by objects. If the object is moving relative to the sensor, a Doppler shift occurs. The shifted wave is mixed with the original wave in two mixers, resulting in two output voltage signals. The phase shift.

OM5232 : CISC->8051/80C51 Family->8031/8051. OM5232; CMOS Single-chip 8-bit Microcontroller.

CS864B1 : MOV Modules. MAXIMUM RATINGS P/N MOVS PER ASSY CONTINUUOUS AC LINE VOLTAGE VOLTS ENERGY x 1000s) TRANSIENT PEAK MAXIMUM CURRENT POWER x 20 s) DISSIPATION RATING (Pm) AMP Pm WATTS ELECTRICAL CHARACTERISTICS MAXIMUM VARISTOR CLAMPING TYPICAL VOLTAGE @ CAPACI(@ 1 mA DC) TEST TANCE CURRENT 1 kHz) x 20 s) MIN MAX VOLTS AMP pF Dimensions in Inches. Standard line.

1129I : Micropower Low Dropout Regulators with Shutdown. 0.4V Dropout Voltage 700mA Output Current 50A Quiescent Current No Protection Diodes Needed Adjustable Output from 30V 3.3V and 5V Fixed Output Voltages Controlled Quiescent Current in Dropout Shutdown 16A Quiescent Current in Shutdown Stable with 3.3F Output Capacitor Reverse Battery Protection No Reverse Output Current Thermal Limiting Surface.

DM15FD : MICA Capacitors. Quick Reference Series DM30 DM42 Lead Spacing: +/-0.8 mm Lead Spacing: +/-0.8 mm Lead Spacing: +/-0.8 mm Lead Spacing: +/-0.8 mm Lead Spacing: +/-0.8 mm Lead Spacing: +/-0.8 mm Lead Spacing: +/-0.8 mm High Capacitance Lead Spacing: +/-0.8 mm High Capacitance Packaging s Page MAXIMUM CAPACITANCE INDICATED MAXIMUM NOMINAL DIMENSIONS IN INCHES MAXIMUM.

SG6742HL : Highly Integrated Green-mode PWM Controller. High-Voltage Startup Low Operating Current: 2.7mA Linearly Decreasing PWM Frequency to 22KHz Frequency Hopping to Reduce EMI Emission Fixed PWM Frequency: 100KHz Peak-Current-Mode Control Cycle-by-Cycle Current Limiting Leading-Edge Blanking (LEB) Synchronized Slope Compensation Internal Open-Loop Protection GATE Output Maximum Voltage Clamp: 18V VDD Under-Voltage.

BP60390 : 70 MHz Bandpass SAW Filter. s Parameter Center Frequency at 25C Insertion Loss 1 dB Bandwidth 3 dB Bandwidth 40dB Bandwidth Passband Variation Phase Linearity Group Delay Variation Absolute Delay Ultimate Rejection Substrate Material Ambient Temperature Note: Component values may change depending on board .

1N922 : Silicon Diode.

AUIRS2191STR : Automotive Grade High Side And Low Side Driver In A 16 Lead SOIC Narrow Package The AUIRS2191S is a high power, high voltage, high speed power MOSFET and IGBT driver with independent high and low side referenced output channels, ideal for Plasma Display Panel and DC-DC converter applications. Logic inputs are compatible with standard CMOS or LSTTL output,.

HHR-20SCPY14F2 : Battery Pack Battery Product; BATTERY PACK NIMH 2.4V 1900 MAH. s: Battery Cell Size: 4/5 SC ; Number of Cells: 2 ; Voltage - Rated: 2.4V ; Capacity: 1.9Ah @ 380mA ; Structure: Side to Side, 1 Row x 2 Cells ; Rechargeability: Yes ; Termination Style: Solder Tab ; Battery Chemistry: Nickel Metal Hydride ; Weight: 0.185 lb (83.91g) ; Lead Free Status:.

ODB600PT-12HB : 12VDC Fan - Dc Fans, Thermal Management Ball; BLOWER DC 12V 120.5X32MM 35CFM. s: Voltage - Rated: 12VDC ; Power (Watts): - ; Bearing Type: Ball ; Size / Dimension: Square - 120.5mm L x 120.5mm H x 32mm W ; Air Flow: 35.0 CFM (0.991m³/min) ; : - ; Termination: 2 Wire Leads ; Fan Type: Blower ; Noise: 49 dB ; RPM: 3000 RPM ; Static Pressure:.

CA3108R28-15P : Aluminum, Olive Drab Cadmium Plated Free Hanging (In-Line), Right Angle Circular Connectors, Interconnect Plug, Male Pins; CONN PLUG 35POS RT ANG W/PINS. s: Connector Type: Plug, Male Pins ; Shell Size - Insert: 28-15 ; Mounting Type: Free Hanging (In-Line), Right Angle ; Fastening Type: Threaded ; : - ; Packaging: Bulk ; Number of Positions: 35 ; Termination:.

F3200CA06 : 250VAC 6A Power Entry - Module Filter IEC 320-C14 (Male Pins); POWER ENTRY FILTERED 6A FASTON. s: Type: IEC 320-C14 (Male Pins) ; Mounting Type: Panel Mount, Screw Hole; Through Hole, Right Angle ; Termination Style: Quick Connect ; Current: 6A ; Voltage: 250VAC ; : - ; Filter Type: General Purpose, Medical ; Fuse Drawer: Fuse Not Required ; Lead Free.

VSC8142VR-03 : Interface - Drivers, Receivers, Transceiver Integrated Circuit (ics) Transceiver Tray 2.375 V ~ 2.625 V; IC TXRX MULTIRATE 16BIT 208-BGA. s: Number of Drivers/Receivers: 1/1 ; Type: Transceiver ; Voltage - Supply: 2.375 V ~ 2.625 V ; Package / Case: 208-BGA ; Packaging: Tray ; Protocol: SONET/SDH ; Lead Free Status: Contains Lead ; RoHS Status: RoHS.

ERJ-B3BJ4R3V : 4.3 Ohm 0.333W, 1/3W Chip Resistor - Surface Mount; RES WIDE TERM 4.3 OHM 5% 0805. s: Resistance (Ohms): 4.3 ; Power (Watts): 0.333W, 1/3W ; Tolerance: 5% ; Packaging: Tape & Reel (TR) ; Composition: Thick Film ; Temperature Coefficient: 200ppm/C ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.

BR5 : RESISTOR, CURRENT SENSE, METAL STRIP, 5 W, 1; 2; 5 %, 20 ppm, 0.005 ohm - 0.05 ohm, THROUGH HOLE MOUNT. s: Category / Application: Current Sensing, General Use ; Technology / Construction: METAL STRIP ; Mounting / Packaging: ThroughHole, Radial Leads, RADIAL LEADED, ROHS COMPLIANT ; Operating Temperature: 85 C (185 F).

 
0-C     D-L     M-R     S-Z