|Description||PWM Step-up Dc/dc Converter|
|Datasheet||Download RH5RH683B-T1 datasheet
The 2B/ 3B Series are PWM Step-up DC/DC converter ICs by CMOS process. The 1A IC consists of an oscillator, a PWM control circuit, a driver transistor (Lx switch), a reference voltage unit, an error amplifier, a phase compensation circuit, resistors for voltage detection, a soft-start circuit, and an Lx switch protection circuit. A low ripple, high efficiency step-up DC/DC converter can be constructed of this 1A IC with only three external components, that is, an inductor, a diode and a capacitor. These 2B/×× 3B ICs can achieve ultra-low supply current (no load) TYP. 15µA by a newly developed PWM control circuit, equivalent to the low supply current of a VFM (chopper) Step-up DC/DC converter. Furthermore, these ICs can hold down the supply current to TYP. 2µA by stopping the operation of the oscillator when the input voltage > (the output voltage set value + the dropout voltage by the diode and the inductor). These 2B/×× 3B Series ICs are recommendable to the user who desires a low ripple PWM DC/DC converter, but cannot adopt a conventional PWM DC/DC converter because of its too large supply current. The 2B/×× 3B Series ICs use the same chip as that employed in the 1A IC and are provided with a drive pin (EXT) for an external transistor. Because of the use of the drive pin (EXT), an external transistor with a low saturation voltage can be used so that a large current can be caused to flow through the inductor and accordingly a large output current can be obtained. Therefore, these 2B/×× 3B Series ICs are recommendable to the user who need a current as large as several tens mA to several hundreds mA. The 3B IC also includes an internal chip enable circuit so that it is possible to set the standby supply current at MAX. 0.5µA. These 2B/×× 3B ICs are suitable for use with battery-powered instruments with low noise and low supply current.FEATURES
Small Number of External Components..........Only an inductor, a diode and a capacitor (RH5RH 1A) Low Supply Current...........................................TYP. 15µA (RH5RH301A) Low Ripple and Low Noise Low Start-up Voltage (when the output current 1mA)..................MAX. 0.9V High Output Voltage Accuracy..........................±2.5% High Efficiency...................................................TYP. 85% Low Temperature-Drift Coefficient of Output Voltage......................TYP. ±50 ppm/°C Soft-Start.............................................................MIN. 500µs Small RH5RH 2B),APPLICATIONS
Power source for battery-powered equipment. Power source for cameras, camcorders, VCRs, PDAs, electronic data banks,and hand-held communication
Power source for instruments which require low noise and low supply current, such as hand-held audio equip-
Power source for appliances which require higher cell voltage than that of batteries used in the appliances.
Lx Vss LxSW PWM control EXT OSC Chip Enable + Error Amp. VLX limiter Buffer Slow start Phase Comp. Vref OUT
Error Amp. (Error Amplifier) has a DC gain of 80dB, and Phase Comp. (Phase Compensation Circuit) provides the frequency characteristics including the 1st pole (fp=0.25Hz) and the zero point (fz=2.5kHz). Furthermore, another zero point (fz=1.0kHz) is also obtained by the resistors and a capacitor connected to the OUT pin.
In RH5RH Series, the output voltage, the driver, and the taping type for the ICs can be selected at the user's request. The selection can be made by designating the part number as shown below RH5RH Part Number b cDescription
Setting Output Voltage (VOUT): Stepwise setting with a step 0.1V in the range 7.5V is possible. Designation of Driver: 1A: Internal Lx Tr. Driver (Oscillator Frequency 50kHz) 2B: External Tr. Driver (Oscillator Frequency 100kHz) 3B: Internal Tr./External Tr. (selectively available) (Oscillator Frequency 100kHz, with chip enable function) Designation of Taping Type : Ex. T1, T2 (refer to Taping Specifications) "T1" is prescribed as a standard.
For example, the product with Output Voltage 5.0V, the External Driver (the Oscillator Frequency 100kHz) and Taping Type T1, is designated by Part Number RH5RH502B-T1.
|Related products with the same datasheet|
|Some Part number from the same manufacture Ricoh Corporation|
|RH5RH683B-T2 PWM Step-up Dc/dc Converter|
|R1210N511C Power Management ICs MARK Informations R1210n Series MARK Specification|
|RQ5RW27CA The Rx5rw Series are Cmos-based Voltage Regulator ICs with high Accuracy Output Voltage and Ultra-low|
|R1183Z 150ma LDO Regulator|
|R1515H100B 50mA Voltage Regulator (wide Input Voltage Range)|
|R1173S001B Super low on Resistance/low Voltage LDO|
|R3112D091A R3112d Series MARK Specification|
|R1180Q121B Series MARK Specification|
|R3111E401A LOW Voltage Detector|
RN5VD15AC-TL : Voltage Detector With Output Delay
RN5RZ38LC-TR : LOW Drop-out AND LOW Noise Voltage Regulator
RX5RW50 : ULTRA SMALL PACKAGE VOLTAGE REGULATOR The Rx5RW Series are CMOS-based voltage regulator ICs with high accuracy output voltage and ultra-low supply current developed. Each of these ICs consists of a driver transistor, a voltage reference unit, an error amplifier, resistors for setting output
R1122N181A-TR-F : FIXED POSITIVE LDO REGULATOR, PDSO5 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: SOT23, Other, ROHS COMPLIANT, SOT-23, 5 PIN ; Life Cycle Stage: ACTIVE
R1130H301B-T2 : 3 V FIXED POSITIVE LDO REGULATOR, 0.34 V DROPOUT, PDSO6 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: Other, SOT-89, 5 PIN ; Life Cycle Stage: ACTIVE ; Output Voltage: 2.94 to 3.06 volts ; IOUT: 0.3000 amps ; VIN: 2.5 to 8 volts ; Dropout Voltage: 0.3400 volts
R1190H083D-T1-F : 2 V FIXED POSITIVE REGULATOR, PDSO5 Specifications: Regulator Type: Standard ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: SOT89, Other, LEAD FREE, PLASTIC, SOT-89, 5 PIN ; Life Cycle Stage: ACTIVE ; Output Voltage: 1.97 to 2.03 volts ; IOUT: 0.6000 amps ; VIN: 3.5 to 16 volts
R1515S74B-E2-F : 2 V FIXED POSITIVE REGULATOR, PDSO6 Specifications: Regulator Type: Standard ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: Other, LEAD FREE, HSOP-6 ; Life Cycle Stage: ACTIVE ; Output Voltage: 1.96 to 2.04 volts ; IOUT: 0.0500 amps ; VIN: 4 to 36 volts
RN5RF37AA-TL : 1 A SWITCHING CONTROLLER, PDSO5 Specifications: Configuration / Function: SINGLE ; Package Type: SOT23, Other, MINI, SOT-23, 5 PIN ; Life Cycle Stage: ACTIVE ; IOUT: 1 amps ; VIN: 4.2 to 10 volts ; Operating Temperature: -40 to 85 C (-40 to 185 F)
RP401N441C-TR-FE : SWITCHING REGULATOR, 1200 kHz SWITCHING FREQ-MAX, PDSO5 Specifications: Configuration / Function: Boost ; Package Type: SOT23, Other, HALOGEN FREE AND ROHS COMPLIANT, SOT-23, 5 PIN ; Life Cycle Stage: ACTIVE ; VIN: 2 volts ; fsw: 1200 kHz ; Operating Temperature: -40 to 85 C (-40 to 185 F)