|
|
Part: BA6811
Category:
Power Management
-> Motor Controller/Drivers
-> DC Motor drivers/Controllers
-> DC Specific
Description: Fan Motor Driver ic
Company: ROHM Electronics
Datasheet: Download BA6811 datasheet File size : 150 kB
Request For quote: Find where to buy BA6811
Datasheet text preview:
Motor driver ICs
Fan motor driver IC
BA6811F / BA6813F
The BA6811F and BA6813F are 2-phase, half-wave motor drivers suited for 12V fan motors. Built-in lock detection and automatic restart mechanisms protect motors. Compact SOP8 (BA6811F / BA6813F) packages reduce the number of external components required. FApplications 2-phase fan motors FFeatures 1) Built-in power transistors. 2) Lock detection and automatic restart mechanisms. 3) Built-in thermal shutdown circuit. FAbsolute maximum ratings (Ta = 25_C)
4) Alarm output pin. (BA6811F) 5) Hall signal output pin. (BA6813F) 6) Built-in reverse current protection diode.
FRecommended operating conditions (Ta = 25_C)
712
Motor driver ICs
FBlock diagram
BA6811F / BA6813F
FPin descriptions
FHall input / output truth table
713
Motor driver ICs
FInput / output equivalent circuits
BA6811F / BA6813F
FElectrical characteristics (unless otherwise noted, Ta = 25_C, VCC = 12V)
714
Motor driver ICs
FCircuit operation The BA6811F and BA6813F have motor lock detection and automatic restart circuits. The timing of lock detection and automatic restart is determined by the external capacitor connected to the LD pin. The charge time of the external capacitor is given by : C S (VLDCL*VLDCP) TON (Charge time)= ILDC TOFF (Discharge time)= C S (VLDCL*VLDCP) ILDD
BA6811F / BA6813F
(Typical value) where VLDCL is the LD-pin clamp voltage (1.93V), (0.76V), VLDCP is the LD-pin comparator voltage (2.9µA), ILDC is the LD-pin charge current (0.52µA), ILDD is the LD-pin discharge current C is the capacitance of the LD-pin external capacitor. For C=1µF, for example, the charge (output ON) and discharge (output OFF) times are 0.40s and 2.25s, respectively. The timing chart for an occasion of motor locking is shown in Fig. 1.
715
Motor driver ICs
FApplication example
BA6811F / BA6813F
FOperation notes (1) Thermal shutdown circuit The IC has a built-in thermal shutdown circuit. The is a temperature difference of 25_C (typical) between the temperatures at which the circuit is activated and deactivated.
The circuit is activated at the temperature of about 175_C (typical), so that all outputs are turned OFF. Normal operation resumes when the circuit is deactivated.
(2) Power consumption Power consumed in the IC can be calculated from the following equation : PC=PC1)PC2)PC3 PC1 is power consumed by the circuit current. PC1=VCC ICC PC2 is the output current consumption. PC2=VOL IO VOL is the LOW level output voltage of output pins 1 and 2, and IO is the sink current of pins 1 and 2. PC3 is power consumed by the AL and HO pins. PC3=VALL IAL)VHOL IHO / 2 where VALL is the AL-pin LOW level voltage, IAL is the AL-pin sink current, VHOL is the HO-pin LOW level voltage, IHO is the HO-pin sink current. Make sure that your application does not exceed the allowable power dissipation of the IC.
716
Others parts begin by ba
BA-1 BA-2 BA-3 BA-4 BA-5 BA-6 BA-7 BA-8 BA-9 BA-10 BA-11 BA-12 BA-13 BA-14 BA-15 BA-16 BA-17 BA-18
|
|
|
