Details, datasheet, quote on part number: STK390-120
PartSTK390-120
CategoryAnalog & Mixed-Signal Processing
Description1-channel + Supply Switching Convergence Correction Circuits
CompanySanyo Semiconductor Corporation
DatasheetDownload STK390-120 datasheet
Quote
Find where to buy
 
  

 

Features, Applications

The is a high-accuracy convergence correction circuit hybrid IC designed to complement the advances in modern high-resolution video projectors and CRT displyas. It incorporates a convergence circuit that operates at high frequency with a corresponding high slew rate, without the increase in power dissipation and mounting, space that discrete devices would entail. It also features a built-in supply switching circuit for high efficiency.

Features

High absolute maximum supply voltage (VCC max = 44V) Low thermal resistance (j-c=2.7C/W) High temperature stability (strengthened idling current temperature compensation) Reduced correction coil inductance to improve stability (over the range fH85kHz) Supply switching circuit built-in to enable large-scale decreases in power dissipation Improved convergence characteristics for CRT displays

Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other parameters) listed in products specifications of any and all SANYO products described or contained herein.

TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
Applications

Parameter Maximum supply voltage Maximum collector current Thermal resistance (1) Thermal resistance (2) Junction temperature Operating temperature Storage temperature Symbol VCC max Tj Tc Tstg VCCH, VCCL Tr9, 10 (per transistor) Tr13, 14 (per transistor) Conditions Ratings to +115 Unit V A C/W C

Parameter Output amplifier block Output noise voltage Quiescent current Neutral voltage Output delay time Output saturation voltage (upper) Output saturation voltage (lower) Supply switching block Supply switching circuit saturation voltage (upper) Supply switching circuit saturation voltage (lower) Supply switching pulse width (upper) Supply switching pulse width (lower) Vsat 9-10 Vsat tPW10 tPW12 Between pins 9 and 10, I=1.0A Between pins 12 and 8, I=1.0A Pin I=1.0A, f=100kHz, BLK input pulse width=1.0s Pin I=1.0A, f=100kHz, BLK input pulse V s VNO ICCO VN tD Vsat 10-7 Vsat Rg=10k, f=100kHz, triangular wave input, VOUT=1.5Vp-p Between pins 10 and 7, I=1.0A Between pins 7 and 12, I=1.0A mVrms s V Symbol Conditions Ratings min typ max Unit

Note. All tests are made using a constant-voltage supply.

Note. Ca, to 120pF) are for VCC switch noise suppression 220F) is for supply switch ON shock noise suppression.

Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be expor ted without obtaining the expor t license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties.

This catalog provides information as of September, 1999. Specifications and information herein are subject to change without notice.


 

Some Part number from the same manufacture Sanyo Semiconductor Corporation
STK390-910
STK391-020 2-channel Convergence Correction Amplifier , Package : Sip
STK391-020 2-channel Convergence Correction Circuit
STK391-110
STK391-120
STK391-220
STK392-010 3-channel Convergence Correction Amplifier , Package : Sip
STK392-010 3-channel Convergence Correction Circuit
STK392-020 3-channel Convergence Correction Amplifier , Package : Sip
STK392-020 Convergence Correction Circuit 3-channel in a Single Package
STK392-040 3-channel Convergence Correction Amplifier , Package : Sip
STK392-040 3-channel Convergence Correction Circuit
STK392-110 Convergence Correction , Package : Sip
STK392-110 3-channel Convergence Correction Circuit
STK392-120
STK392-220
STK392-550
STK392-560
STK392-570
STK393-110
STK393-120

2SJ257 :

LA7685J : Pal/ntsc Single-chip Color Television Signal Processing Circuit

LB1690 : 3-phase Motor Driver

LC573404A : 4-bit Singl-chip Microcomputer With LCD Driver

LC665316A : Dual Oscillator on Chip, 4-bit ad Converter (4ch), Package : Dip

LC865020B : 8-bit (20480 X 8bit ROM) Single-chip Microcontroller

SL-2324-20 :

SLP-4132C-81 :

Same catergory

2SA1358 : Transistor ( Audio Frequency Power Amplifier Applications ).

AD2S90 : Low Cost, Complete 12-Bit Resolver-to-digital Converter.

BQ2092 : Gas Gauge ic With Smbus-like Interface. Provides accurate measurement of available charge in NiCd, NiMH, and Li-Ion rechargeable batteries Supports SBData charge control commands for Li-Ion, NiMH, and NiCd chemistries Designed for battery pack integration The bq2092 Gas Gauge IC With SMBus-Like Interface is intended for battery-pack or in-system installation to maintain an accurate record.

INA126 : . The INA126 and INA2126 are precision instrumentation amplifiers for accurate, low noise differential signal acquisition. Their two-op-amp design provides excellent performance with very low quiescent current (175A/chan.). This, combined with wide operating voltage range to 18V, makes them ideal for portable instrumentation and data acquisition systems.

KH205 : 170MHz, Hybrid op Amp. The is a wideband overdrive-protected operational amplifier designed for applications needing both speed and low power operation. Utilizing a well-established current feedback architecture, the KH205 exhibits performance far beyond that of conventional voltage feedback op amps. For example, the KH205 has a bandwidth at a gain of +20 and settles in 22ns.

LC7972VB : CMOS Operational Amplifier Programmable Offset Correction Function. CMOS Operational Amplifier with Programmable Offset Correction Function The LC7972VA and LC7972VB are dual inverting/noninverting operational amplifier ICs that are fabricated in a CMOS process. These ICs provide a programmable offset correction function and a power saving function for use when the operational amplifier is unused, both of which can be controlled.

LM3080 : Operational Transconductance Amplifier (discontinued). The is a programmable transconductance block intended to fulfill a wide variety of variable gain applications The LM3080 has differential inputs and high impedance push-pull outputs The device has high input impedance and its transconductance (gm) is directly proportional to the amplifier bias current (IABC) High slew rate together with programmable.

LM3302 : Low Power Low Offset Voltage Quad Comparator. The LM139 series consists of four independent precision voltage comparators with an offset voltage as low 2 mV max for all four comparators. These were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude.

LMC6062 : LMC6062 - Precision CMOS Dual Micropower Operational Amplifier, Package: Soic Narrow, Pin Nb=8.

LMX2240 : Intermediate Frequency Receiver (obsolete). The is a monolithic integrated intermediate frequency receiver suitable for use in Digital European Cordless Telecommunications (DECT) systems as well as other mobile telephony and wireless communications applications It is fabricated using National's ABiCTM IV BiCMOS process (fT e 15 GHz) The LMX2240 consists of a high gain limiting amplifier a frequency.

MAX1666S : Power. Advanced Lithium-ion Battery-pack Protector. The MAX1666 provides complete protection against overvoltage, undervoltage, overcharge current, overdischarge current, and cell mismatch for to 4-cell Lithium-Ion battery packs. The voltage of each cell in the battery pack is checked and compared to the programmable threshold and to the other cells in the pack. The MAX1666 protects the battery pack.

MAX2411A : Low-cost RF Up/downconverter With Lna And pa Driver. o Low-Cost Silicon Bipolar Design o Integrated Upconvert/Downconvert Function o Operates from a Single to +5.5V Supply o 3.2dB Combined Receiver Noise Figure: 2.4dB (LNA) 9.2dB (mixer) o Flexible Power-Amplifier Driver: 18dBm Output Third-Order Intercept (OIP3) 35dB Gain-Control Range o LO Buffer for Low LO Drive Level o Low Power Consumption: 60mW.

NJM2114 : High-performance Low-noise Dual Operational Amplifier.

OPA2650E : Dual Wideband, Low Power Voltage Feedback Operational Amplifier. Dual Wideband, Low Power Voltage Feedback OPERATIONAL AMPLIFIER q LOW POWER: 50mW/Chan. q UNITY GAIN STABLE BANDWIDTH: 360MHz q FAST SETTLING TIME: 0.01% q LOW HARMONICS: 5MHz q DIFFERENTIAL GAIN/PHASE ERROR: 0.01%/0.025 q HIGH OUTPUT CURRENT: 85mA The is a dual, low power, wideband voltage feedback operational amplifier. It a high bandwidth 360MHz.

OPA2652E : Dual, 700mhz, Voltage-feedback Operational Amplifier. For most current data sheet and other product information, visit www.burr-brown.com q WIDEBAND BUFFER: +1 q WIDEBAND LINE DRIVER: +2 q HIGH OUTPUT CURRENT: 140mA q LOW SUPPLY CURRENT: 5.5mA/Ch q ULTRA-SMALL PACKAGE: SOT23-8 q LOW dG/d 0.05%/0.03 q HIGH SLEW RATE: 335V/sec q SUPPLY VOLTAGE: to 6V The is a dual, low-cost, wideband voltagefeedback amplifier.

OPA734 : 0.05uV/degC (max), Single-supply CMOS Zero-drift Operational Amplifierseries of CMOS Operational Amplifiers Use Auto-zeroing Techniques to Simultaneously Provide Low Offset Voltage (5V Max), And Near-zero Drift Over Time And Temperature. These Miniature, High-precision, Low Quiescent Current Amplifiers Offer High Input Impedance And Rail-to-rail Output.

TLV2344Y : Lincmose Low-voltage High-speed Operational Amplifiers. Wide Range of Supply Voltages Over Specified Temperature Range: 8 V Fully Characterized 3 V and 5 V Single-Supply Operation Common-Mode Input-Voltage Range Extends Below the Negative Rail and Up to VDD at 25C Output Voltage Range Includes Negative Rail High Input Impedance. 1012 Typical ESD-Protection Circuitry Designed-In Latch-Up Immunity The TLV234x.

SRQ-2116 : The SRQ-2116Z is a high-linearity, silicon germanium direct demodulator designed for direct conversion and low-IF basestation receivers. This device high second- and third-order intermodulation suppression, high LO-RF isolation and excellent quadrature accuracy..

EC1089B : InGaP HBT Gain Block. The is a high dynamic range driver amplifier in a low-cost surface mount package. The InGaP/GaAs HBT is able to achieve high performance across a broad range with +41 dBm OIP3 and +24 dBm of compressed 1dB power. It is housed in an industry standard lead-free/green/RoHScompliant SOT-89 package. All devices are 100% RF and DC tested. The EC1089 is targeted.

RH6200M : Low Noise, High Speed Rail-to-Rail Op Amp The RH6200 is an ultralow noise, rail-to-rail input and output unity-gain stable op amp that 0.95nV/?Hz noise voltage. This amplifier combines very low noise with a 165MHz gain bandwidth, 50V/?s slew rate and is optimized for low voltage signal conditioning systems. A shutdown pin reduces supply current during.

 
0-C     D-L     M-R     S-Z