Details, datasheet, quote on part number: STK4241V
PartSTK4241V
CategoryAnalog & Mixed-Signal Processing
Descriptionaf Power Amplifier (120W + 120W)
CompanySanyo Semiconductor Corporation
DatasheetDownload STK4241V datasheet
Quote
Find where to buy
 
  

 

Features, Applications

STK4241V AF Power Amplifier (Split Power Supply) (120W+120W min, THD = 0.08%)
Features

Muting circuit built-in to isolate all types of shock noise Current mirror circuit for low 0.08% total harmonic distortion Pin compatible with the STK4201II series (THD = 0.4%) and the STK4141X series (THD = 0.02%)

Specifications

Parameter Maximum supply voltage Thermal resistance Junction temperature Operating substrate temperature Storage temperature Available time for load short-circuit1 Symbol VCC max j-c Tj Tc Tstg ts VCC = 120W Conditions Ratings +125 1 Unit V C/W C s

Parameter Recommended supply voltage Load resistance Symbol VCC RL Conditions Ratings 54 8 Unit V
SANYO Electric Co., Ltd. Semiconductor Business Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN

Parameter Quiescent current Output power Total harmonic distortion Frequency response Input impedance Output noise voltage2 Neutral voltage Muting voltage Symbol ICCO PO THD fL, fH ri VNO VN VM Conditions VCC = 66V THD = 1.0W,

Notes. All tests are measured using a regulated voltage supply unless otherwise specified. 1. Available time for load short-circuit and output noise voltage are measured using the transformer supply specified below. 2. The output noise voltage is the peak value of an average-reading meter with an rms value scale (VTVM). The noise voltage waveform includes no flicker noise.


 

Some Part number from the same manufacture Sanyo Semiconductor Corporation
STK4244MK5
STK4272
STK4273 2 Channel af Power Amp
STK4273-G
STK4274 Current Amp
STK4275
STK4277-SL
STK430
STK4301
STK4301S
STK430MK2
STK430MK3
STK430MK4
STK4311
STK4311S
STK433
STK433-105
STK4332
STK4332 af Power Amplifier (5W + 5W)
STK433A
STK435
Same catergory

2SK389 : N-channel Junction Type ( Low Noise Audio And Differential Amplifier Applications ).

AD734 : 10 Mhz, 4-Quadrant Multiplier/divider. High Accuracy 0.1% Typical Error High Speed 10 MHz Full-Power Bandwidth V/ s Slew Rate 200 ns Settling 0.1% at Full Power Low Distortion 80 dBc from Any Input Third-Order IMD Typically 75 dBc at 10 MHz Low Noise 94 dB SNR, to 20 kHz 70 dB SNR, to 10 MHz Direct Division Mode 2 MHz BW at Gain of 100 APPLICATIONS High Performance Replacement for AD534.

ALD4212 : CMOS Low Voltage, High Speed Precision Quad SPST no Analog Switches. CMOS LOW VOLTAGE HIGH SPEED QUAD PRECISION ANALOG SWITCHES GENERAL The ALD4211/ALD4212/ALD4213 are quad SPST CMOS analog switches specifically designed for low voltage, high speed applications where 0.2pC charge injection, 200pf sampling capacitor, and picoamp leakage current are important analog switch operating characteristics. These analog switches.

AMSOP-07CS : Low Offset Voltage Operational Amplifier. APPLICATIONS High-Gain Instrumentation Precision Data Acquisition Precision Integrators Precision Threshold Detectors Biomedical Amplifiers Low VOS. 75 V Max Low VOS Drift. 1.3 V/ C Max Ultra Stable with Time 1.5 V/Month Max Low Noise.0.6 VP-P Max Wide Input Voltage Range. 14V Wide Supply Voltage Range 18V The is a precision operational.

BA10324A : . The BA10324A, BA10324AF, and BA10324AFV are monolithic ICs with four built-in operational amplifiers featuring internal phase compensation. Either a dual or single power supply can be driven, and these products can be driven by a digital system 5V single power supply. These products can be used in a wide range of administrative and industrial applications,.

GX4314 : Wideband, Monolithic 4x1video Multiplexer. low differential phase and gain wide bandwidth, 100 MHz -1 dB (Flattened) small switching transient 11 volts supplies CIRCUIT The is a wideband video multiplexer implemented in bipolar technology. This device is characterized by excellent differential phase and gain in the enabled state, very high off-isolation in the disabled state and fully buffered.

HMA510GM-55883 : 16 X 16-bit CMOS Parallel Multiplier Accumulator. The is a high speed, low power CMOS x 16-bit parallel multiplier accumulator capable of operating at 55ns clocked multiply-accumulate cycles. The 16-bit X and Y operands may be specified as either two's complement or unsigned magnitude format. Additional inputs are provided for the accumulator functions which include: loading the accumulator with the current.

INA138NA/250 : Difference Amplifiers. ti INA138, High-side Measurement Current Shunt Monitor.

LM239AQDREP : ti LM239A-EP, Military Enhanced Plastic Quad, General Purpose Differential Comparator.

LTC1047CS : Dual Micropower Chopper Stabilized Operational Amplifier With Internal Capacitors.

LTC1164AC : Low Power, Low Noise, Quad Universal Filter Building Block.

LTC6910-3CTS8 : LTC6910-3, Programmable Gain Amplifier in SOT-23 (Gain of 0,1,2,3,4,5,6, And 7V/V).

NE/SE521 : High-speed Dual-differential Comparator/sense Amp. The is a fast slewing high performance operational amplifier which retains DC performance equal to the best general purpose types while providing far superior large-signal AC performance. A unique input stage design allows the amplifier to have a large-signal response nearly identical to its small-signal response. The amplifier is compensated for truly.

OPA131P : ti OPA131, General Purpose Fet-input Operational Amplifiers. q FET INPUT: = 50pA max q LOW OFFSET VOLTAGE: 750V max q WIDE SUPPLY RANGE: 18V q SLEW RATE: 10V/s q WIDE BANDWIDTH: 4MHz q EXCELLENT CAPACITIVE LOAD DRIVE q SINGLE, DUAL, QUAD VERSIONS The OPA131 series of FET-input op amps provides high performance at low cost. Single, dual, and quad versions in industry-standard pinouts allow cost-effective design.

STK4028X : af Power Amplifier (30W). STK4028X AF Power Amplifier (Split Power Supply) (30W min, THD = 0.018%) Compact packaging supports slimmer set designs Series designed for to 100W and pin-compatibility Simpler heat sink design facilitates thermal design of slim stereo sets Current mirror circuit application reduces distortion to 0.018% Supports additon of electronic circuits for thermal.

TS1871 : 1.8V, Input/ouput Rail to Rail Low Power Op-amps. 1.8V INPUT/OUTPUT RAIL TO RAIL LOW POWER OPERATIONAL AMPLIFIERS s OPERATING AT VCC 6V s RAIL TO RAIL INPUT & OUTPUT s EXTENDED Vicm 0.2V to VCC 0.2V) s LOW SUPPLY CURRENT (400A) s GAIN BANDWIDTH PRODUCT (1.6MHz) s HIGH STABILITY s ESD TOLERANCE (2kV) s LATCH-UP IMMUNITY s AVAILABLE IN SOT23-5 MICROPACKAGE The TS187x (Single, Dual & Quad) is an operational.

UC1543 : Power. Power Supply Supervisory Circuit. Includes Over-voltage, Under-voltage, And Current Sensing Circuits Internal 1% Accurate Reference Programmable Time Delays SCR "Crowbar" Drive Of 300mA Remote Activation Capability Optional Over-voltage Latch Uncommitted Comparator Inputs For Low Voltage Sensing (UC1544 Series Only) The monolithic integrated circuits contain all the functions necessary.

UPC8130TA : -15 DBM Input, Variable Gain Amplifier Silicon Mmic For Transmitter Agc of Digital Cellular Telephone.

ISL28176 : Single, Dual And Quad Micropower Single Supply Rail-to-Rail Input And Output (RRIO) Precision Op Amp The ISL28176, ISL28276 and ISL28476 are single, dual and quad channel micropower operational amplifiers optimized for single supply operation over the 2.4V to 5V range. They can be operated from one lithium cell or two Ni-Cd batteries. These devices.

 
0-C     D-L     M-R     S-Z