|
Details, datasheet, quote on part number:GP1UE291QK
| |
| Part: | GP1UE291QK |
| Category: | Optoelectronics => Drivers/Controllers => Infrared/Remote Control => Remote Control Receiver Modules |
| Description: | IR Remote Control Receiver |
| Company: | Sharp Microelectronics of the Americas |
| Datasheet: | Download GP1UE291QK datasheet File size : 49 kB |
| Request For quote: | Find where to buy GP1UE291QK
|
| |
Datasheet text preview:
GP1UE29QK Series
GP1UE29QK Series
s Features
1. Low dissipation current:MAX. 0.6mA (at VCC=3V) 2. Low operating voltage:2.4 to 3.6V 3. Anti electromagnetic induction noise type. 4. Compact (case volume) 5. Various B.P.F. (Band Pass Frequency) frequency to meet different user needs
Low Voltage Operation, Anti Electromagnetic Induction Noise Type, Compact IR Detecting Unit for Remote Control
s Outline Dimensions
(Unit : mm)
5.6 2.9 7.2
2.2
2.7
s Applications
1. AV equipment 2. Home appliances
0.65 1
0.65 18.6
±1
*1
Parameter Supply voltage *1 Operating temperature Storage temperature *2 Soldering temperature
Symbol VCC Topr Tstg Tsol
2.54
*1
2.54 1.2 4.3
1 1.8
0.4 3.4 11.2
1 2 3
123
1.8 3.2
0.8 0.5
0.8
*1
*1
6 9
*1 No dew condensation is allowed *2 For 5s (At mounting on PCB with thickness of 1.6mm)
VOUT VCC GND
s Recommended Operating Conditions
Parameter Supply voltage Symbol Operating conditions V CC 2.4 to 3.6 Unit V
Example of mounting drawing from solder side (Reference) Top of lenz 2.54 3-0.8 1 2.1 5.05 8.2 2.54
23
*2
1.4 2.9
*2
1.4
*2
5.8
1. *1 : Indicates root dimensions of connector. 2. Unspecified tolerance:±0.3 3. Case thickness:0.3TYP 4. *2 : If there are difficulties to insert the GP1UE29QK series on PCB, we recommend to expand +0.1mm from original 2.9mm.
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://sharp-world.com/ecg/
2.1
2.9
2.85
3.6
s Absolute Maximum Ratings
( T a= 2 5 ° C ) Rating Unit V 0 to +6.0 -10 to +70 °C -20 to +70 °C 260 °C
1
19
GP1UE29QK Series s Model Line-up
Diversified models with a different B.P.F. frequency are also available. Model No. B.P.F. center frequency Unit GP1UE29QK 40 GP1UE290QK 36 kHz GP1UE291QK 38 GP1UE292QK 36.7 GP1UE297QK 56.8
s Internal Block Diagram
RL VOUT Limiter B.P.F. Demodulator Integrator Comparator VCC GND
s Electro-optical Characteristics
Parameter Symbol Conditions
Dissipation current High level output voltage Low level output voltage High level pulse width Low level pulse width B.P.F. center frequency Output pull-up resistance
ICC VOH VOL T1 T2 f0 RL
No input light
*3
IOL=1.6mA
- -
(Ta=25°C, VCC=+3V) MIN. TYP. MAX. Unit mA - 0.4 0.6 - - V VCC-0.5 - - V 0.45 µs - 1 200 600 µs - 400 1 000 *4 - - kHz 70 100 130 k
*3 The burst wave as shown in the following figure shall be transmitted by the transmitter shown in Fig.1 The carrier frequency of the transmitter, however, shall be same as *4, and measurement shall be from just after starting the transmission until 50 pulse *4 The B.P.F. center frequency f0 varies with model, as shown in s Model Line-up
Burst wave
600µs
1 000µs f0=(*4) Duty 50%
GP1UE29QK Series s Performance
Using the transmitter shown in Fig. 1, the output signal of the light detecting unit is good enough to meet the following items in the standard optical system in Fig. 2. 1. Linear reception distance characteristics When L=0.2 to 8.0(6.5)*7m, *5EV<10 lx and =0° in Fig.2, the output signal shall meet the electrical characteristics in the attached list. 2. Sensitivity angle reception distance characteristics When L=0.2 to 6.0(4.5)*7m, *5EV<10 lx and 30° in Fig.2, the output signal shall meet the electrical characteristics in the attached list. 3. Anti outer peripheral light reception distance characteristics When L=0.2 to 4.0(3.0)*7m, *6EV 300 lx and =0° in Fig.2, the output signal shall meet the electrical characteristics in the attached list.
*5 It refers to detector face illuminance *6 Outer peripheral light source: CIE standard light source A shall be used and placed at 45° from perpendicular axis at the detector face center *7 In case of B.P.F. center frequency:56.8kHz model
Fig.1 Transmitter
20cm PD49PI 10k 10µF +5V
10k
Transmitter (GL521 used) f0=(*4) Duty 50%
VOUT Oscilloscope
In the above figure, the transmitter should be set so that the output VOUT (P-P) can be 40mV. However, the PD49PI to be used here should be of the short-circuit current ISC=2.6µ A at EV =100 lx. (EV is an illuminance by CIE standard light source A (tungsten lamp).)
Fig.2 Standard Optical System
Light detector face illuminance:EV Reception distance:L Transmitter ( indicates horizontal and vertical directions.) VOUT
|
|
