|Category||Power Management => Supervisory Circuits => Voltage Detectors => voltage detectors+voltage regulators|
|Title||voltage detectors+voltage regulators|
|Description||Feature = Battery Backup Switching ic ;; Composition = 2V/R + 3V/D + SW ;; Output Current = - ;; Output Voltage = 2.3-5.4 V (0.1V Step) ;; Detection Voltage = 2.4-5.3 V(CS), 1.7-3.4 V(PREEND, RESET) ;; Accuracy = ±2% ;; Current Consumption = 15 µA Max. (Operating) 2.1 µA Max. (Back Up) ;; Package (Power Dissipation) = 8-pin Tssop 8-pin Son (B)|
|Datasheet||Download S-8424A datasheet
The S-8424A Series is a CMOS IC designed for use in the switching circuits of primary and backup power supplies on a single chip. It consists of two voltage regulators, three voltage detectors, a power supply switch and its controller, as well as other functions. In addition to the switching function between the primary and backup power supply, the S-8424A Series can provide the micro controllers with three types of voltage detection output signals corresponding to the power supply voltage. Moreover adopting a special sequence for switch control enables the effective use of the backup power supply, making this IC ideal for configuring a backup system.Features
Low power consumption Normal operation: 15 µA Max. (VIN 6 V) Backup: 2.1 µA Max. Voltage regulator Output voltage tolerance ±2 % Output voltage: Independently selectable 0.1 V steps in the range 5.4 V Three built-in voltage detectors (CS, PREEND , RESET ) Detection voltage precision: ±2 % Detection voltage: Selectable 0.1 V steps in the range 5.3 V (CS voltage detector) Selectable 0.1 V steps in the range V ( PREEND , RESET voltage detector) Switching circuit for primary power supply and backup power supply configurable on one chip Efficient use of backup power supply possible Special sequence Backup voltage is not output when the primary power supply voltage does not reach the initial voltage at which the switch unit operates.8-Pin TSSOP (Package drawing No.: FT008-A) 8-Pin SON(B) (Package drawing No.: PA008-B)
Video camera recorders Still video cameras Memory cards SRAM backup equipment
BATTERY BACKUP SWITCHING IC S-8424A Series Selection Guide
Caution Set the CS voltage so that the switch voltage (VSW1) is equal to or greater than the RESET detection voltage (-VDET2). Remark 1. The selection range is as follows. VRO, VOUT: (0.1 V steps) (0.1 V steps) (0.1 V steps (0.1 V steps) If a product with a voltage other than above is required, contact our sales representative.
xx IC direction in tape specification TB: 8-Pin TSSOP TF: 8-Pin SON(B) Package code FT: 8-Pin TSSOP PA: 8-Pin SON(B) Serial code
|Related products with the same datasheet|
|Some Part number from the same manufacture Seiko Instruments|
|S-8424AAAFT-TB Feature = Battery Backup Switching ic ;; Composition = 2V/R + 3V/D + SW ;; Output Current = - ;; Output Voltage = 2.3-5.4 V (0.1V Step) ;; Detection Voltage = 2.4-5.3 V(CS), 1.7-3.4 V(PREEND, RESET) ;; Accuracy|
|S-8425 Feature = Battery Backup Switching ic ;; Composition = 3V/R + 2V/D + SW ;; Output Current = - ;; Output Voltage = 2.3-5.4 V (0.1V Step) ;; Detection Voltage = 2.4-5.3 V(CS), 1.7-3.4 V (RESET) ;; Accuracy|
|S-8430AF Step up & Down Voltage Regulator|
|S-8435AF-SK-T1 Step up Switching Regulator|
S-1323B30 : Features = RR 70dB SC-82AB ;; Input Voltage = 2.0-6.5V ;; Output Voltage = 1.5-5.5V ;; Output Current = 150 ma ;; Accuracy = ±1% ;; Current Consumption Typ. = 70 µA ;; Current Consumption Standby = 0.1 µA ;; Dropout Voltage = 500mV @150mA ;; Condition = Vout=3.0V, Vin=4V ;; Package (P
S-816A44AMC-BAT-T2 : Features = Low Dropout Controller ;; Input Voltage = 16 V Max. ;; Output Voltage = 2.5-6.0V ;; Output Current = 1A (External PNP Tr) ;; Accuracy = ±2% ;; Current Consumption Typ. = 30 µA ;; Current Consumption Standby = 1 µA ;; Dropout Voltage = 100 MV @100mA ;; Condition = Vout=3.0V,
S-817B32AMC-CWVT2G : SUPER-SMALL PACKAGE CMOS VOLTAGE REGULATOR The S-817 Series is a 3-terminal positive voltage egulator, developed using CMOS technology. Small ceramic capacitors can be used as the output capacitor, and the S-817 series provides stable operation with low loads down to 1 µA.
S-1711A2533-I6T1G : SUPER-SMALL PACKAGE 2-CIRCUIT HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR S-1711A1515-I6T1G S-1711A1515-M6T1G S-1711A1518-I6T1G ? S-1711A1526-I6T1G ? S-1711A1528-I6T1G S-1711A1528-M6T1G S-1711A152J-I6T1G ? ? S-1711A1529-M6T1G S-1711A1533-I6T1G S-1711A1533-M6T1G
S-1711B2818-I6T1G : SUPER-SMALL PACKAGE 2-CIRCUIT HIGH RIPPLE-REJECTION LOW DROPOUT CMOS VOLTAGE REGULATOR S-1711A1515-I6T1G S-1711A1515-M6T1G S-1711A1518-I6T1G ? S-1711A1526-I6T1G ? S-1711A1528-I6T1G S-1711A1528-M6T1G S-1711A152J-I6T1G ? ? S-1711A1529-M6T1G S-1711A1533-I6T1G S-1711A1533-M6T1G
S-L2985A38-H4T1 : HIGH Ripple-rejection WLP Package LOW Dropout CMOS Voltage Regulator
S-1702GGE01-I6T1U : 3.1 V FIXED POSITIVE LDO REGULATOR, 0.23 V DROPOUT, PDSO6 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: Other, LEAD FREE, SNT-6A ; Life Cycle Stage: ACTIVE ; Output Voltage: 3.07 to 3.13 volts ; IOUT: 0.1500 amps ; VIN: 2 to 6.5 volts ; Dropout Voltage: 0.2300 volts
S-1702JGJ00-I6T1U : 3.1 V FIXED POSITIVE LDO REGULATOR, 0.23 V DROPOUT, PDSO6 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Fixed ; Package Type: Other, LEAD FREE, SNT-6A ; Life Cycle Stage: ACTIVE ; Output Voltage: 3.07 to 3.13 volts ; IOUT: 0.1500 amps ; VIN: 2 to 6.5 volts ; Dropout Voltage: 0.2300 volts
S-8333ACAC-T8T1G : 0.16 A SWITCHING CONTROLLER, 1133 kHz SWITCHING FREQ-MAX, DSO8 Specifications: Configuration / Function: SINGLE ; Package Type: Other, LEAD FREE, SNT-8 ; Life Cycle Stage: ACTIVE ; IOUT: 0.1600 amps ; VIN: 3.3 volts ; fsw: 1133 kHz ; Operating Temperature: -40 to 85 C (-40 to 185 F)
SG-310SCF16.0000MB : CRYSTAL OSCILLATOR, CLOCK, 16 MHz, LVCMOS OUTPUT Specifications: Oscillator Type: XO ; Package / Form Factor: Surface Mount ; Features / Standards: RoHS, Lead-Free ; Frequency: 16 MHz ; Operating Temperature: -20 to 70 C (-4 to 158 F) ; Supply Voltage: 3.3 Volts ; Output Type: LVCMOS
AN7703 : Fixed. Low-dropout Three-pin Voltage Regulator 1.2-a Type. The AN7700, AN7700F, and AN7700SP series are stabilized constant-voltage power supplies with small difference between I/O voltages (0.5 V typ.). They are suitable for low-voltage, battery-driven equipment, and home appliances and industrial equipment with great fluctuation of the supply voltage. The output voltage ranges: For 20 V, and 24 V For 12 V, and V AN7700.
BA6283N : . The BA6283N and BA6955N are reversible-motor drivers with a maximum output current of 1.0A. Two logic inputs allow four output modes: forward, reverse, stop (standby), and brake. The built-in power save circuit suppresses current consumption in the motor stop mode. ! 1) Logic and driver sections have separate ground pins; this allows the IC to drive.
BQ2057DGK : ti BQ2057, Li-ion Low-dropout Linear (4.1V) Charge Management ic For One-cell Applications With Autocomptm.
CS51220 : Voltage Mode PWM Controllers. CS51220 Feed Forward Voltage Mode PWM Controller with Programmable Synchronization is a single output PWM Controller with switching frequency to 500 kHz. The feed forward voltage mode control provides excellent line regulation for wide input range. This PWM controller has a synchronization output allowing programmable phase delay. For overcurrent protection,.
FAN2504 : Low-dropout Voltage Regulator. Ultra Low Power Consumption 200 mV dropout voltage 75 µA ground current 200 mA Enable/Shutdown Control SOT23-5 package Thermal limiting 300 mA peak current wide variety of external capacitors, and the compact SOT23-5 surface-mount package. The FAN2504/05 family of products offer significant improvements over older BiCMOS designs and are pin-compatible.
HD74HCT74A : Dual D-type Positive Edge-triggered Flip Flops With Clear And Preset. Dual Dtype Positive Edgetriggered Flip Flops with Clear and Preset The HD74HCT74A has independent data, preset, clear, and clock inputs Q and Q outputs a 14 pin package. The logic level present at the data input is transferred to the output during the positive going transition of the clock pulse. Preset and clear are independent of the clock and accomplished.
KD1083V : 7.5a Low Drop Positive Voltage Regulator Adjustable And Fixed. 7.5A LOW DROP POSITIVE VOLTAGE REGULATOR ADJUSTABLE AND FIXED THREE TERMINAL ADJUSTABLE OR FIXED OUTPUT VOLTAGE 3.0, 3.3V OUTPUT CURRENT 7.5A 1.4V MAX DROPOUT VOLTAGE AT FULL LOAD LINE REGULATION: MAX 0.2% OVER FULL TEMPERATURE RANGE LOAD REGULATION: MAX 0.5% OVER FULL TEMPERATURE RANGE OUTPUT CURRENT LIMIT THERMAL SHUTDOWN PROTECTION WITH HYSTERESIS.
L4941Series : LDO. Very Low Drop 1a Regulator. LOW DROPOUT VOLTAGE (450mV Typ. at 1A) VERY LOW QUIESCENT CURRENT THERMAL SHUTDOWN SHORT CIRCUIT PROTECTION REVERSE POLARITY PROTECTION The is a three terminal 5V positive regulators available TO-220, TO-220FP and D2PAK packages, making it useful in a wide range of industrial and consumer applications. Thanks to its very low input/output voltage drop,.
L6221 : Power Controllers & Motor Drivers. Quad Darlington Switch. FOUR NON INVERTING INPUTS WITH ENABLE OUTPUT VOLTAGE 50 V OUTPUT CURRENT 1.8 A VERY LOW SATURATION VOLTAGE TTL COMPATIBLE INPUTS INTEGRAL FAST RECIRCULATION DIODES The L6221 monolithic quad darlington switch is designed for high current, high voltage switching applications. Each of the four switches is controlled by a logic input and all four are controlled.
LD2982AM18R : 1.8V- Very Low Drop And Low Noise Regulator. VERY LOW DROP AND LOW NOISE VOLTAGE REGULATOR WITH INHIBIT FUNCTION VERY LOW DROPOUT VOLTAGE AT 50mA AND AT 1mA LOAD) VERY LOW QUIESCENT CURRENT (375µA TYP. AT 50mA LOAD AND AT 1mA) OUTPUT CURRENT TO 50mA LOGIC CONTROLLED ELECTRONIC SHUTDOWN OUTPUT VOLTGAE OF 5V INTERNAL CURRENT AND THERMAL LIMIT AVAILABLE ± 1% TOLLERANCE (AT 25°C, A VERSION) SUPPLY.
LT580JH : Precision References.
PJ78M00Series : . PJ78M00 Series 3-Terminal Medium Current Positive Voltage Regulators he PJ78M00Series positive voltage regulators are identical to the popular PJ7800Series devices, except that they are specified for only half the output current. Like thhe PJ7800 devices, the PJ78Mxx Terminal regulators are intended for local,ocard voltage regulation. Internal current.
PT4662A : Plug-in Power Solutions->Isolated->Multiple Output. ti PT4662, 3.3V/2.5V 30A Dual Output 48V-Input ISOlated DC/DC Converter.
STSR3 : Synchronous Rectifiers Smart Driver For Flyback. SUPPLY VOLTAGE RANGE: TO 5.5V TYPICAL PEAK OUTPUT CURRENT: (SOURCE 2A, SINK 3.5A) OPERATING FREQUENCY: TO 750 KHz SMART TURN-OFF ANTICIPATION TIMING AUTOMATIC TURN OFF FOR DUTY CYCLE LESS THAN 14% POSSIBILITY TO OPERATE IN DISCONTINUOUS MODE STSR3 Smart Driver IC provides a high current outputs to properly drive secondary Power Mosfets used as Synchronous.
UC3878DWP : Soft Switching. ti UC3878, Phase Shift Resonant Controller.
UTCTL494 : = Voltage Mode PWM Control ic ;; Package = DIP-16, SOP-16 ;;. The UTC TL494 incorporates all the functions required in the construction of a pulse-width modulation switching circuit. Designed primarily for switching power supply control or DCDC convectors, it offers the systems engineer the flexibility to tailor control circuitry to its own application. *Complete PWM power control circuitry *Uncommitted outputs.
STTH2006 : and benefits ■ Ultrafast switching ■ Low reverse current ■ Low thermal resistance ■ Reduces switching and conduction losses The STTH2006 uses ST Turbo 2 600 V technology and is especially suited for use in switching power supplies, and industrial applications, such as rectification and continuous mode PFC boost diode..
FSBF5CH60B : Smart Power Module t is an advanced smart power module (SPM) that Fairchild has newly developed and designed to provide very compact and high performance ac motor drives mainly targeting lowpower inverter-driven application like air conditioner and washing machine. It combines optimized circuit protection and drive matched to low-loss IGBTs. System.
AP5726 : Step-up DC/DC Converter The AP5726 is a step-up DC/DC converter specifically designed to drive white LEDs with a constant current. The device can drive 2~6 LEDs in series from a Li-Ion cell. Series connection of the LEDs provides identical LED currents resulting in uniform brightness and eliminates the need for ballast resistors. The AP5726 switches.