Details, datasheet, quote on part number: M27C1024-10B3X
CategoryMemory => EPROM => 8 Mb
Description1 Mbit 64kb X16 uv EPROM And OTP EPROM
CompanyST Microelectronics, Inc.
DatasheetDownload M27C1024-10B3X datasheet


Features, Applications

10% SUPPLY VOLTAGE in READ OPERATION FAST ACCESS TIME: 35ns LOW POWER CONSUMPTION: Active Current 5MHz Standby Current 100A PROGRAMMING VOLTAGE: 0.25V PROGRAMMING TIME: 100s/byte (typical) ELECTRONIC SIGNATURE Manufacturer Code: 0020h Device Code: 008Ch

DESCRIPTION The a 1 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable). It is ideally suited for microprocessor systems requiring large data or program storage and is organized as 65,536 words of 16 bits. The FDIP40W (window ceramic frit-seal package) has a transparent lid which allows the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written to the device by following the programming procedure. For application where the content is programmed only one time and erasure is not required, the M27C1024 is offered PDIP40, PLCC44 and x 14mm) packages. Table 1. Signal Names

G P VPP VCC VSS Address Inputs Data Outputs Chip Enable Output Enable Program Supply Voltage Ground

DEVICE OPERATION The modes of operations of the M27C1024 are listed in the OperatingModes table. A single power supply is required in the read mode. All inputs are TTL levels except for Vpp and on A9 for Electronic Signature. Read Mode The M27C1024 has two control functions, both of which must be logically active in order to obtain data at the outputs. Chip Enable (E) is the power control and should be used for device selection. Output Enable (G) is the output control and should be used to gate data to the output pins, independent of device selection. Assuming that the addresses are stable, the address access time (tAVQV) is equalto the delay from E to output (tELQV). Data is available at the output after a delay of tOE from the falling edge of G, assuming that E has been low and the addresses have been stable for at least t AVQV-tGLQV. Standby Mode The M27C1024 has a standby mode which reduces the active current from to 100A. The M27C1024 is placed in the standby mode by applying a TTL high signal to the E input. When in the standby mode, the outputs are in a high impedance state, independent of the G input.

Parameter Ambient Operating Temperature Under Bias Storage Temperature Input or Output Voltages (except A9) Supply Voltage A9 Voltage Program Supply Voltage

Notes: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not i mplied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Minimum DC voltage on Input or Output is 0.5V with possible undershoot to 2.0V for a period less than 20ns. Maximum DC voltage on Output is VCC +0.5V with possible overshoot to VCC +2V for a period less than 20ns. 3. Depends on range.

Mode Read Output Disable Program Verify Program Inhibit Standby Electronic Signature
- Q15 Data Output Hi-Z Data Input Data Output Hi-Z Codes
Identifier Manufacturer's Code Device Code A0 VIL VIH Q0 0 Hex Data 20h 8Ch


Related products with the same datasheet
Some Part number from the same manufacture ST Microelectronics, Inc.
M27C1024-10B6TR 1 Mbit 64kb X16 uv EPROM And OTP EPROM
M27C1024-10C1 1 Mbit (64KB X16) uv EPROM And OTP EPROM
M27C1024-10C1TR 1 Mbit 64kb X16 uv EPROM And OTP EPROM
M27C1024-12-1 1 Mbit (64KB X16) uv EPROM And OTP EPROM
M27C1024-12B1TR 1 Mbit 64kb X16 uv EPROM And OTP EPROM
M27C1024-12C1 1 Mbit (64KB X16) uv EPROM And OTP EPROM
M27C1024-12C1TR 1 Mbit 64kb X16 uv EPROM And OTP EPROM

2N2905A : Small Signal PNP Transistors

STPS41L45CG : Power Schottky Diodes->45 and 60V Power Schottky D Low Drop Power Schottky Rectifier

65N55F3 : N-channel 55V - 8.0m ohm - 65A - DPAK Stripfet TM Power Mosfet

STM8AP5X67TAY : Automotive 8-bit MCU, with up to 128 Kbytes Flash, Eeprom, 10-bit ADC, Timers, LIN, CAN, Usart, SPI, I2C, 3 V to 5.5 V

STGD10NC60HDT4 : Igbt - Single Discrete Semiconductor Product 20A 600V 60W Standard; IGBT N-CH 20A 600V DPAK Specifications: Input Type: Standard ; Voltage - Collector Emitter Breakdown (Max): 600V ; Current - Collector (Ic) (Max): 20A ; Vce(on) (Max) @ Vge, Ic: 2.5V @ 15V, 5A ; Power - Max: 60W ; Mounting Type: Surface Mount ; Package / Case: TO-252-3, DPak (2 Leads + Tab), SC-63 ; Packaging: Cut Tape (CT

SM6T56CA : Tv - Diode Circuit Protection 47.6V 600W; TRANSIL 600W 56V BIDIR SMB Specifications: Package / Case: DO-214AA, SMB ; Packaging: Tape & Reel (TR) ; Polarization: Bidirectional ; Power (Watts): 600W ; Voltage - Reverse Standoff (Typ): 47.6V ; Voltage - Breakdown: 53.2V ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

ST1L02PM18 : ADJUSTABLE POSITIVE LDO REGULATOR, PDSO6 Specifications: Regulator Type: Low Dropout ; Output Polarity: Positive ; Output Voltage Type: Adjustable / Variable ; Package Type: Other, 3 X 3 MM, LEAD FREE, DFN-6 ; Life Cycle Stage: ACTIVE

ST72P561K6TC/XXXS : 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 16 MHz ; ROM Type: MROM ; Supply Voltage: 4.5 to 5.5 volts ; I/O Ports: 48 ; Package Type: LFQP, Other, 10 X 10 MM, LQFP-64 ; Operating Range: Commercial ; Pin Count: 64 ; Operating Temperature: 0 to 70 C (32 to 158 F) ; Features: PWM

T410-700K : 700 V, 4 A, 4 QUADRANT LOGIC LEVEL TRIAC Specifications: Thyristor Type: Triac, 4 QUADRANT LOGIC LEVEL TRIAC ; Pin Count: 3 ; VDRM: 700 volts ; IT(RMS): 4 amps ; Standards and Certifications: RoHS

L99DZ120TR : Motor/Motion/Ignition Controllers & Drivers STMicroelectronics L99DZ100/120 Automotive Door Actuator Drivers are door zone systems ICs that provide electronic control modules with enhanced power management power supply functionality. This functionality includes various standby modes, and LIN physical communication layers. The devices two l

0-C     D-L     M-R     S-Z