Details, datasheet, quote on part number: M27C2001-10L1TR
CategoryMemory => EPROM => 8 Mb
Description2 Mbit 256kb X 8 uv EPROM And OTP EPROM
CompanyST Microelectronics, Inc.
DatasheetDownload M27C2001-10L1TR datasheet


Features, Applications


PROGRAMMING VOLTAGE: 0.25V PROGRAMMING TIME: 100s/byte (typical) ELECTRONIC SIGNATURE Manufacturer Code: 20h Device Code: 61h

DESCRIPTION The is a high speed 2 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable). It is ideally suited for microprocessor systems requiring large programs and is organised by 8 bits. The FDIP32W (window ceramic frit-seal package) and LCCC32W (leadless chip carrier package) have a transparent lids which allow the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written to the device by following the programming procedure. For applications where the content is programmed only one time and erasure is not required, the M27C2001 is offered PDIP32, PLCC32 and x 20 mm) packages. Table 1. Signal Names

G P VPP VCC VSS Address Inputs Data Outputs Chip Enable Output Enable Program Supply Voltage Ground

The operationg modes of the M27C2001 are listed in the Operating Modes table. A single power supply is required in the read mode. All inputs are TTL levels except for VPP and on A9 for Electronic Signature. Read Mode The M27C2001 has two control functions, both of which must be logically active in order to obtain data at the outputs. Chip Enable (E) is the power control and should be used for device selection. Output Enable (G) is the output control and should be used to gate data to the output pins, independent of device selection. Assuming that the addresses are stable, the address access time (tAVQV) is equal to the delay from E to output (tELQV). Data is available at the output after a delay of t GLQV from the falling edge of G, assuming that E has been low and the addresses have been stable for at least tAVQV-tGLQV. Standby Mode The M27C2001 has a standby mode which reduces the supply current from to 100A. The M27C2001 is placed in the standby mode by applying a CMOS high signal to the E input. When in the standby mode, the outputs are in a high impedance state, independent of the G input.

Symbol TA TBIAS TSTG VIO (2) VCC VA9 (2) VPP Parameter Ambient Operating Temperature (3) Temperature Under Bias Storage Temperature Input or Output Voltage (except A9) Supply Voltage A9 Voltage Program Supply Voltage Value to 14 Unit C

Note: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Minimum DC voltage on Input or Output is 0.5V with possible undershoot to 2.0V for a period less than 20ns. Maximum DC voltage on Output is VCC +0.5V with possible overshoot to VCC +2V for a period less than 20ns. 3. Depends on range.

Mode Read Output Disable Program Verify Program Inhibit Standby Electronic Signature
Q0-Q7 Data Out Hi-Z Data In Data Out Hi-Z Codes
Identifier Manufacturer's Code Device Code A0 VIL VIH 0 1 Hex Data 20h 61h

Two Line Output Control Because EPROMs are usually used in larger memory arrays, this product features a 2 line control function which accommodates the use of multiple memory connection. The two line control function allows: a. the lowest possible memory power dissipation, b. complete assurance that output bus contention will not occur.

For the most efficient use of these two control lines, E should be decoded and used as the primary device selecting function, while G should be made a common connection to all devices in the array and connected to the READ line from the system control bus. This ensures that all deselected memory devices are in their low power standby mode and that the output pins are only active when data is required from a particular memory device.


Related products with the same datasheet
Some Part number from the same manufacture ST Microelectronics, Inc.
M27C2001-10L1X 2 Mbit 256kb X 8 uv EPROM And OTP EPROM
M27C2001-12-1 2 Mbit (256KB X8) uv EPROM And OTP ROM
M27C2001-12B1TR 2 Mbit 256kb X 8 uv EPROM And OTP EPROM
M27C2001-15-1 2 Mbit (256KB X8) uv EPROM And OTP ROM
M27C2001-15B1TR 2 Mbit 256kb X 8 uv EPROM And OTP EPROM

M27C4001-70XC1X : 4 Mbit 512kb X 8 uv EPROM And OTP EPROM

M58LW032C90N6F : 32 Mbit 2mb X16, Uniform Block, Burst 3v Supply Flash Memory

PSD835F2-B-15U : Configurable Memory System on a Chip For 8-bit Microcontrollers

STTH302S : 200V Ultra-Fast Diodes High Efficiency Ultrafast Diode

M28R400CT100D16 : 4 Mbit (256kb x16, Boot Block) 1.8V Supply Flash Memory

M29F080D70N : 8 Mbit (1Mb x8, Uniform Block) 5V Supply Flash Memory

PSD833F5V-20 : Flash In-system Programmable ISP Peripherals For 8-bit MCUs

ST7P10BF0U3 : 8-bit MCU WITH Single Voltage Flash Memory, DATA Eeprom, ADC, 5 Timers, SPI

STGW50HF60S : Igbt - Single Discrete Semiconductor Product 110A 600V 284W Standard; IGBT 600V 110A TO-247 Specifications: Input Type: Standard ; Voltage - Collector Emitter Breakdown (Max): 600V ; Current - Collector (Ic) (Max): 110A ; Vce(on) (Max) @ Vge, Ic: 1.45V @ 15V, 30A ; Power - Max: 284W ; Mounting Type: Through Hole ; Package / Case: TO-247-3 ; Packaging: Tube ; Lead Free Status: Lead Free ; R

ST72321BR6T1 : 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 16 MHz ; ROM Type: MROM ; Supply Voltage: 3.8 to 5.5 volts ; I/O Ports: 48 ; Package Type: LFQP, Other, 10 X 10 MM, ROHS COMPLIANT, LQFP-64 ; Operating Range: Industrial ; Pin Count: 64 ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Feat

STM8AH6186TAX : MICROCONTROLLER, PQFP32 Specifications: Life Cycle Stage: ACTIVE ; Package Type: LFQP, Other, 7 X 7 MM, LQFP-32 ; Pin Count: 32

5962-8512801VSA : HC/UH SERIES, ASYN NEGATIVE EDGE TRIGGERED 12-BIT UP BINARY COUNTER, CDFP16 Specifications: Counter Type: BINARY COUNTER ; Counter Category: Asynchronous ; Counter Direction: UP ; Supply Voltage: 4.5 ; Package Type: CERAMIC, FP-16 ; Logic Family: CMOS, HC/UH ; Number of Pins: 16 ; Number of Stages (Bits): 12 bits ; Clock Frequency: 22 MHz ; Operating Temperature: -55 to 125

0-C     D-L     M-R     S-Z