Details, datasheet, quote on part number: M27C2001-70C6
PartM27C2001-70C6
Category
Description2 Mbit (256KB X8) uv EPROM And OTP ROM
CompanyST Microelectronics, Inc.
DatasheetDownload M27C2001-70C6 datasheet
Quote
Find where to buy
 
  

 

Features, Applications

10% SUPPLY VOLTAGE in READ OPERATION ACCESS TIME: 55ns LOW POWER CONSUMPTION: Active Current 5MHz Standby Current 100A

PROGRAMMING VOLTAGE: 0.25V PROGRAMMING TIME: 100s/word ELECTRONIC SIGNATURE Manufacturer Code: 20h Device Code: 61h

DESCRIPTION The is a high speed 2 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable). It is ideally suited for microprocessor systems requiring large programs and is organised by 8 bits. The FDIP32W (window ceramic frit-seal package) and LCCC32W (leadless chip carrier package) have a transparent lids which allow the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written to the device by following the programming procedure. For applications where the content is programmed only one time and erasure is not required, the M27C2001 is offered PDIP32, PLCC32 and x 20 mm) packages.

A0-A17 Q0-Q7 Address Inputs Data Outputs Chip Enable Output Enable Program Supply Voltage Ground

Symbol TA TBIAS TSTG VIO (2) VCC VA9 (2) VPP Parameter Ambient Operating Temperature (3) Temperature Under Bias Storage Temperature Input or Output Voltage (except A9) Supply Voltage A9 Voltage Program Supply Voltage Value to 14 Unit C

Note: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Minimum DC voltage on Input or Output is 0.5V with possible undershoot to 2.0V for a period less than 20ns. Maximum DC voltage on Output CC +0.5V with possible overshoot to VCC +2V for a period less than 20ns. 3. Depends on range.

Mode Read Output Disable Program Verify Program Inhibit Standby Electronic Signature
Q7-Q0 Data Out Hi-Z Data In Data Out Hi-Z Codes
Identifier Manufacturer's Code Device Code A0 VIL VIH 0 1 Hex Data 20h 61h

 

Related products with the same datasheet
M27C2001-10C1
M27C2001-55C1
M27C2001-70XF1
M27C2001-10C6
Some Part number from the same manufacture ST Microelectronics, Inc.
M27C2001-70C6TR 2 Mbit 256kb X 8 uv EPROM And OTP EPROM
M27C2001-70XF1 2 Mbit (256KB X8) uv EPROM And OTP ROM
M27C2001-70XF1TR 2 Mbit 256kb X 8 uv EPROM And OTP EPROM
M27C2001-80-1 2 Mbit (256KB X8) uv EPROM And OTP ROM
M27C2001-80B1TR 2 Mbit 256kb X 8 uv EPROM And OTP EPROM
M27C2001-90C1 2 Megabit -256k X 8- uv EPROM And OTP ROM
M27C2001-90C1TR 2 Mbit 256kb X 8 uv EPROM And OTP EPROM

LK112SM36TR : 1.3V - Low Drop/ Low Quiescent Regulator With Inhibit

M27C256B-45N3TR : 256 Kbit ( 32kb X 8 ) uv EPROM And OTP EPROM

PSD4235F1-C-15U : Flash In-system-programmable Peripherals For 16-bit MCUs

PSD913F1V-90J : Flash In-system Programmable Isp Peripherals For 8-bit MCUs

ST24C08R : 8 Kb Serial EePROM I(2)c-bus, 2.5v to 5.5v, With Write Protection: 1kx8

ST52T410G1B6 : 8-bit Intelligent Controller Unit Icu Three Timer/pwms, ADC, WDG

STGP7NB120SD : N-channel 7A 1200V TO-220 Powermesh Igbt

M93C76-BN6G/S : 16kbit, 8kbit, 4kbit, 2kbit and 1kbit (8-bit or 16-bit Wide) Microwire Serial Access Eeprom

UPSD3214BV-40U1T : Flash Programmable System Device with 8032 Microcontroller Core

PSD954F5-12UI : Flash In-system Programmable ISP Peripherals For 8-bit MCUs

M24SR64-YMN6T/2 : RFID Transponders 64-Kbit Dynamic NFC RFID tag EEProm STMicroelectronics M24SR Dynamic NFC/RFID Tag ICs are dynamic NFC/RFID tag ICs with a dual interface. These devices include embedded EEPROM memory in 2K, 4K, 16K and 64K versions. They can be operated from an IC interface or by a 13.56MHz RFID reader or an NFC phone. The IC interface uses a two

 
0-C     D-L     M-R     S-Z