Details, datasheet, quote on part number: M27C2001-80L1TR
PartM27C2001-80L1TR
CategoryMemory => EPROM => 8 Mb
Description2 Mbit 256kb X 8 uv EPROM And OTP EPROM
CompanyST Microelectronics, Inc.
DatasheetDownload M27C2001-80L1TR datasheet
  

 

Features, Applications

10% SUPPLY VOLTAGE in READ OPERATION FAST ACCESS TIME: 55ns LOW POWER CONSUMPTION: Active Current 5MHz Standby Current 100A

PROGRAMMING VOLTAGE: 0.25V PROGRAMMING TIME: 100s/byte (typical) ELECTRONIC SIGNATURE Manufacturer Code: 20h Device Code: 61h

DESCRIPTION The is a high speed 2 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable). It is ideally suited for microprocessor systems requiring large programs and is organised by 8 bits. The FDIP32W (window ceramic frit-seal package) and LCCC32W (leadless chip carrier package) have a transparent lids which allow the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written to the device by following the programming procedure. For applications where the content is programmed only one time and erasure is not required, the M27C2001 is offered PDIP32, PLCC32 and x 20 mm) packages. Table 1. Signal Names

G P VPP VCC VSS Address Inputs Data Outputs Chip Enable Output Enable Program Supply Voltage Ground

The operationg modes of the M27C2001 are listed in the Operating Modes table. A single power supply is required in the read mode. All inputs are TTL levels except for VPP and on A9 for Electronic Signature. Read Mode The M27C2001 has two control functions, both of which must be logically active in order to obtain data at the outputs. Chip Enable (E) is the power control and should be used for device selection. Output Enable (G) is the output control and should be used to gate data to the output pins, independent of device selection. Assuming that the addresses are stable, the address access time (tAVQV) is equal to the delay from E to output (tELQV). Data is available at the output after a delay of t GLQV from the falling edge of G, assuming that E has been low and the addresses have been stable for at least tAVQV-tGLQV. Standby Mode The M27C2001 has a standby mode which reduces the supply current from to 100A. The M27C2001 is placed in the standby mode by applying a CMOS high signal to the E input. When in the standby mode, the outputs are in a high impedance state, independent of the G input.

Symbol TA TBIAS TSTG VIO (2) VCC VA9 (2) VPP Parameter Ambient Operating Temperature (3) Temperature Under Bias Storage Temperature Input or Output Voltage (except A9) Supply Voltage A9 Voltage Program Supply Voltage Value to 14 Unit C

Note: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Minimum DC voltage on Input or Output is 0.5V with possible undershoot to 2.0V for a period less than 20ns. Maximum DC voltage on Output is VCC +0.5V with possible overshoot to VCC +2V for a period less than 20ns. 3. Depends on range.

Mode Read Output Disable Program Verify Program Inhibit Standby Electronic Signature
Q0-Q7 Data Out Hi-Z Data In Data Out Hi-Z Codes
Identifier Manufacturer's Code Device Code A0 VIL VIH 0 1 Hex Data 20h 61h

Two Line Output Control Because EPROMs are usually used in larger memory arrays, this product features a 2 line control function which accommodates the use of multiple memory connection. The two line control function allows: a. the lowest possible memory power dissipation, b. complete assurance that output bus contention will not occur.

For the most efficient use of these two control lines, E should be decoded and used as the primary device selecting function, while G should be made a common connection to all devices in the array and connected to the READ line from the system control bus. This ensures that all deselected memory devices are in their low power standby mode and that the output pins are only active when data is required from a particular memory device.


 

Related products with the same datasheet
M27C2001-10B1X
M27C2001-10B6TR
M27C2001-10B6X
M27C2001-10C1TR
M27C2001-10C1X
M27C2001-10C6TR
M27C2001-10C6X
M27C2001-10F1TR
M27C2001-10F1X
M27C2001-10F6TR
M27C2001-10F6X
M27C2001-10L1TR
Some Part number from the same manufacture ST Microelectronics, Inc.
M27C2001-80L1X 2 Mbit 256kb X 8 uv EPROM And OTP EPROM
M27C2001-90C1 2 Megabit -256k X 8- uv EPROM And OTP ROM
M27C2001-90C1TR 2 Mbit 256kb X 8 uv EPROM And OTP EPROM
M27C202 2 Mbit (128KB X16) uv EPROM And OTP EPROM
M27C202-100B1
M27C202-100B1TR 2 Mbit 128kb X16 uv EPROM And OTP EPROM
 
0-C     D-L     M-R     S-Z