Details, datasheet, quote on part number: M27C202-200F6TR
PartM27C202-200F6TR
CategoryMemory => EPROM => 8 Mb
Description2 Mbit 128kb X16 uv EPROM And OTP EPROM
CompanyST Microelectronics, Inc.
DatasheetDownload M27C202-200F6TR datasheet
  

 

Features, Applications

10% SUPPLY VOLTAGE in READ OPERATION ACCESS TIME: 45ns LOW POWER CONSUMPTION: Active Current 5MHz Standby Current 100A

PROGRAMMING VOLTAGE: 0.25V PROGRAMMING TIME: 100s/word ELECTRONIC SIGNATURE Manufacturer Code: 20h Device Code: 1Ch

DESCRIPTION The a 2 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable). It is ideally suited for microprocessor systems requiring large programs, in the application where the contents is stable and needs to be programmed only one time, and is organised by 16 bits. The FDIP40W (window ceramic frit-seal package) has a transparent lids which allow the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written to the device by following the programming procedure. For applications where the content is programmed only one time and erasure is not required, the M27C202 is offered PDIP40, PLCC44 and x 14 mm) packages.

A0-A16 Q0-Q15 Address Inputs Data Outputs Chip Enable Output Enable Program Supply Voltage Ground Not Connected Internally

Symbol TA TBIAS TSTG VIO (2) VCC VA9 (2) VPP Parameter Ambient Operating Temperature (3) Temperature Under Bias Storage Temperature Input or Output Voltage (except A9) Supply Voltage A9 Voltage Program Supply Voltage Value to 14 Unit C

Note: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Minimum DC voltage on Input or Output is 0.5V with possible undershoot to 2.0V for a period less than 20ns. Maximum DC voltage on Output is VCC +0.5V with possible overshoot to VCC +2V for a period less than 20ns. 3. Depends on range.

Mode Read Output Disable Program Verify Program Inhibit Standby Electronic Signature
Q15-Q0 Data Output Hi-Z Data Input Data Output Hi-Z Codes
Identifier Manufacturer's Code Device Code A0 VIL VIH Q0 0 Hex Data 20h 1Ch

 

Related products with the same datasheet
M27C202-100B3TR
M27C202-100B6TR
M27C202-100F1TR
M27C202-100F3TR
M27C202-100F6TR
M27C202-100K1TR
M27C202-100K3TR
M27C202-100K6TR
M27C202-100N1TR
M27C202-100N3TR
M27C202-100N6TR
M27C202-120B1TR
Some Part number from the same manufacture ST Microelectronics, Inc.
M27C202-200K1TR 2 Mbit 128kb X16 uv EPROM And OTP EPROM
M27C202-45-1 2 Mbit (128KB X16) uv EPROM And OTP EPROM
M27C202-45B1TR 2 Mbit 128kb X16 uv EPROM And OTP EPROM
M27C202-70-1 2 Mbit (128KB X16) uv EPROM And OTP EPROM
M27C202-70B1TR 2 Mbit 128kb X16 uv EPROM And OTP EPROM
M27C202-70K6 2 Mbit (128KB X16) uv EPROM And OTP EPROM
M27C202-70K6TR 2 Mbit 128kb X16 uv EPROM And OTP EPROM
M27C202-80-1 2 Mbit (128KB X16) uv EPROM And OTP EPROM
M27C202-80B1TR 2 Mbit 128kb X16 uv EPROM And OTP EPROM
M27C202-80F1 2 Mbit (128KB X16) uv EPROM And OTP EPROM
M27C202-80F1TR 2 Mbit 128kb X16 uv EPROM And OTP EPROM
M27C256B 256 Kbit (32KB X8) uv EPROM And OTP EPROM
M27C256B-10B1TR 256 Kbit ( 32kb X 8 ) uv EPROM And OTP EPROM
M27C256B-10C6 256 Kbit (32KB X8) uv EPROM And OTP EPROM
M27C256B-10C6TR 256 Kbit ( 32kb X 8 ) uv EPROM And OTP EPROM
M27C256B-10F1 256k -32k X 8- uv EPROM And OTP ROM
M27C256B-10F1TR 256 Kbit ( 32kb X 8 ) uv EPROM And OTP EPROM
 
0-C     D-L     M-R     S-Z