Details, datasheet, quote on part number: M28C64C-200N1
PartM28C64C-200N1
CategoryMemory => ROM => EEPROM
Description64 Kbit 8kb x8 Parallel EePROM
CompanyST Microelectronics, Inc.
DatasheetDownload M28C64C-200N1 datasheet
Quote
Find where to buy
 
  

 

Features, Applications

FAST ACCESS TIME: 150ns SINGLE 10% SUPPLY VOLTAGE LOW POWER CONSUMPTION FAST WRITE CYCLE 32 Bytes Page Write Operation Byte or Page Write Cycle: 5ms ENHANCED END OF WRITE DETECTION Ready/Busy Open Drain Output (for M28C64C product only) Data Polling Toggle Bit PAGE LOAD TIMER STATUS BIT HIGH RELIABILITY SINGLE POLYSILICON, CMOS TECHNOLOGY Endurance >100,000 Erase/Write Cycles Data Retention >40 Years JEDEC APPROVED BYTEWIDE PIN OUT DESCRIPTION The an 8 Kbit x8 low power Parallel EEPROM fabricated with STMicroelectronics proprietary single polysilicon CMOS technology. The device offers fast access time with low power dissipation and requires a 5V power supply. The circuit has been designed to offer a flexible microcontroller interface featuring both hardware and software handshakingmode with Ready/Busy, Data Polling and Toggle Bit. The M28C64C supports 32 byte page write operation. Table 1. Signal Names

G RB VCC VSS Address Input Data Input / Output Write Enable Chip Enable Output Enable Ready / Busy Supply Voltage Ground


PIN DESCRITPION Addresses (A0-A12). The address inputs select an 8-bit memory location during a read or write operation.

Chip Enable (E). The chip enable input must be low to enable all read/write operations. When Chip Enable is high, power consumption is reduced. Output Enable (G). The Output Enable input controls the data output buffers and is used to initiate read operations.

Symbol TA T STG VCC IO VI VESD Parameter Ambient Operating Temperature Storage Temperature Range Supply Voltage Input/Output Voltage Input Voltage Electrostatic Discharge Voltage (Human Body model) Value 0.3 to VCC 6.5 2000 Unit C

Note: Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents.

Mode Read Write Standby / Write Inhibit Write Inhibit Write Inhibit Output Disable
- DQ7 Data Out Data In Hi-Z Data Out or Hi-Z Data Out or Hi-Z

Data In/ Out - DQ7). Data is written to or read from the M28C64C through the I/O pins. Write Enable (W). The Write Enable input controls the writing of data to the M28C64C. Ready/Busy (RB). Ready/Busy is an open drain output that can be used to detect the end of the internal write cycle. OPERATION In order to prevent data corruption and inadvertent write operations during power-up, a Power On Reset (POR) circuit resets all internal programming cicuitry. Access to the memory in write mode is allowed after a power-up as specified in Table 6. Read The M28C64C is accessed like a static RAM. When E and G are low with W high, the data addressed is presented on the I/O pins. The I/O pins are high impedancewhen either E is high.

Write operations are initiated when both W and E are low and G is high.The M28C64C supports both E and W controlled write cycles. The Address is latched by the falling edge or W which ever occurs last and the Data on the rising edge or W which ever occurs first. Once initiated the write operation is internally timed until completion. Page Write Page write allows to 32 bytes to be consecutively latched into the memory prior to initiating a programming cycle. All bytes must be located in a single page address, that - A12 must be the same for all bytes. The page write can be initiated during any byte write operation. Following the first byte write instruction the host may send another address and data to a maximum of 100s after the rising edge or W which ever occurs first (t BLC). If a transition W is not detected within 100s, the internal programming cycle will start.


 

Related products with the same datasheet
M28C64C-150MS6
M28C64C-150N1
M28C64C-150N6
M28C64C-150P6
M28C64C-200K6
M28C64C-200MS1
M28C64C-200MS6
M28C64C-200N6
M28C64C-200P6
M28C64C-250K1
M28C64C-250K6
Some Part number from the same manufacture ST Microelectronics, Inc.
M28C64C-200N6 64 Kbit 8kb x8 Parallel EePROM
M28C64C-250 Obsolete - 64K (8K X 8) Parallel EePROM
M28C64C-250K1 64 Kbit 8kb x8 Parallel EePROM
M28C64X Obsolete - 64K (8K X 8) Parallel EePROM
M28C64X-150K1 64 Kbit 8kb x8 Parallel EePROM
M28F101 1 Megabit -128k X 8, Chip Erase- Flash Memory
M28F101-100K1 1 MB 128k X 8, Chip Erase Flash Memory
M28F101-100P1 1 Megabit -128k X 8, Chip Erase- Flash Memory
M28F101-100P3 1 MB 128k X 8, Chip Erase Flash Memory
M28F101-120-1 1 Megabit -128k X 8, Chip Erase- Flash Memory
M28F101-120K3 1 MB 128k X 8, Chip Erase Flash Memory
M28F101-120N1 1 Megabit -128k X 8, Chip Erase- Flash Memory
M28F101-120N3 1 MB 128k X 8, Chip Erase Flash Memory
M28F101-150-1 1 Megabit -128k X 8, Chip Erase- Flash Memory
M28F101-150K3 1 MB 128k X 8, Chip Erase Flash Memory
M28F101-150P1 1 Megabit -128k X 8, Chip Erase- Flash Memory
M28F101-150P3 1 MB 128k X 8, Chip Erase Flash Memory
M28F101-150P6 1 Megabit -128k X 8, Chip Erase- Flash Memory
M28F101-150XK1 1 MB 128k X 8, Chip Erase Flash Memory
M28F101-200-1 1 Megabit -128k X 8, Chip Erase- Flash Memory

LK112SM46TR : 1.3V - Low Drop/ Low Quiescent Regulator With Inhibit

M27256-20-6 : NND - NMOS 256 Kbit (32KB X8) uv EPROM

ST10F269-T3 : ST10 Family 16-BIT MCU With Mac Unit, 256K Byte Flash Memory And 12K Byte RAM

ST232E : +/- 15kv Esd Protected 5v Rs-232 Transceiver

ST6260B : ST6 Family 8-BIT Microcontroller ( MCU ) With Otp, ROM, Fastrom, EPROM, A/D Converter, Safe Reset, Auto-reload Timer, EePROM And Spi

M25P128-VME6G : 128 Mbit (Multilevel), Low Voltage, Serial Flash Memory With 50MHz SPI Bus Interface The M25P128 is a multilevel 128Mbit (16Mbit x 8) Serial Flash Memory, with advanced write protection mechanisms, accessed by a high speed SPI-compatible bus. The memory can be programmed 1 to 256 bytes at a time,

STGP10HF60KD : Datasheet 10 A - 600 V - Short-circuit Rugged IGBT Datasheet 10 A - 600 V - short-circuit rugged IGBT

ST62E20LM6/EPROM : 8-bit MCUs WITH A/D Converter, TWO Timers, Oscillator Safeguard & SAFE Reset

NAND01GR4M5AZB5F : 256/512mb/1gb (x8/x16, 1.8/3v, 528 Byte Page) NAND Flash Memories + 256/512mb (x16/x32, 1.8v) Lpsdram, MCP

LY510ALHTR : Gyroscopes GYROSCOPE MEMS SGL AXIS 16-LGA -; GYROSCOPE MEMS SGL AXIS 16-LGA Specifications: Sensitivity: 10mV//s ; Voltage - Supply: 2.7 V ~ 3.6 V ; Current - Supply: 4.8mA ; Output Type: Analog ; Package / Case: 16-LFLGA ; Typical Bandwidth: 140Hz ; Range /s: 100/s ; Operating Temperature: -40C ~ 85C ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

STD3LN62K3 : Fet - Single Discrete Semiconductor Product 2.5A 620V 45W Surface Mount; MOSFET N-CH 620V 2.5A DPAK Specifications: Mounting Type: Surface Mount ; FET Type: MOSFET N-Channel, Metal Oxide ; Drain to Source Voltage (Vdss): 620V ; Current - Continuous Drain (Id) @ 25 C: 2.5A ; Rds On (Max) @ Id, Vgs: 3 Ohm @ 1.25A, 10V ; Input Capacitance (Ciss) @ Vds: 386pF @ 50V ; Power - Max: 45W ; Packaging: Tap

STM8AH6146TAXXXX : MICROCONTROLLER, PQFP32 Specifications: Life Cycle Stage: ACTIVE ; Package Type: LFQP, Other, 7 X 7 MM, LQFP-32 ; Pin Count: 32

 
0-C     D-L     M-R     S-Z