Details, datasheet, quote on part number: M28F101-150P3
CategoryMemory => Flash
Description1 MB 128k X 8, Chip Erase Flash Memory
CompanyST Microelectronics, Inc.
DatasheetDownload M28F101-150P3 datasheet
Find where to buy


Features, Applications

5V 10% SUPPLY VOLTAGE 12V PROGRAMMING VOLTAGE FAST ACCESS TIME: 70ns BYTE PROGRAMING TIME: 10s typical ELECTRICAL CHIP ERASE in 1s RANGE LOW POWER CONSUMPTION Stand-by Current: 100A max 10,000 ERASE/PROGRAM CYCLES INTEGRATED ERASE/PROGRAM-STOP TIMER OTP COMPATIBLE PACKAGES and PINOUTS ELECTRONIC SIGNATURE Manufacturer Code: 20h Device Code: 07h DESCRIPTION The M28F101 FLASH Memory is a non-volatile memory which may be erased electrically at the chip level and programmed byte-by-byte. It is organised as 128K bytes of 8 bits. It uses a command register architecture to select the operating modes and thus provides a simple microprocessor interface. The M28F101 FLASH Memory is suitable for applications where the memory has to be reprogrammed in the equipment. The access time of 70ns makes the device suitable for use in high speed microprocessor systems.

G W VPP VCC VSS April 1997 Address Inputs Data Inputs / Outputs Chip Enable Output Enable Write Enable Program Supply Voltage Ground

Symbol TA TSTG VIO VCC VA9 VPP Parameter Ambient Operating Temperature Storage Temperature Input or Output Voltages Supply Voltage A9 Voltage Program Supply Voltage, during Erase or Programming Value to 14 Unit C

Note: Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the SGS-THOMSON SURE Program and other relevant quality documents.

DEVICE OPERATION The M28F101 FLASH Memory employs a technology similar a 1 Megabit EPROM but adds to the device functionality by providing electrical erasure and programming. These functions are managed by a command register. The functions that are addressed via the command register depend on the voltage applied to the VPP, program voltage, input. When VPP is less than or equal to 6.5V, the command register is disabled and M28F101 functions as a read only memory providing operating modes similar to an EPROM (Read, Output Disable, Electronic Signature Read and Standby). When VPP is raised to 12V the command regsiter is enabled and this provides, in addition, Erase and Program operations. READ ONLY MODES, VPP 6.5V For all Read Only Modes, except Standby Mode, the Write Enable input W should be High. In the Standby Mode this input is don't care. Read Mode. The M28F101 has two enable inputs, E and G, both of which must be Low in order to output data from the memory. The Chip Enable (E) is the power control and should be used for device selection. Output Enable (G) is the output control and should be used to gate data on to the output, independant of the device selection. Standby Mode. In the Standby Mode the maximum supply current is reduced. The device is placed in the Standby Mode by applying a High to the Chip Enable (E) input. When in the Standby Mode the outputs are in a high impedance state, independant of the Output Enable (G) input.

Output Disable Mode. When the Output Enable (G) is High the outputs are in a high impedance state. Electronic Signature Mode. This mode allows the read out of two binary codes from the device which identify the manufacturer and device type. This mode is intended for use by programming equipment to automatically select the correct erase and programming algorithms. The Electronic Signature Mode is active when a high voltage 13V) is applied to address line A9 with E and G Low. With A0 Low the output data is the manufacturer code, when A0 is High the output is the device type code. All other address lines should be maintained Low while reading the codes. The electronic signature may also be accessed in Read/Write modes. READ/WRITE MODES, 11.4V VPP 12.6V When VPP is High both read and write operations may be performed. These are defined by the contents of an internal command register. Commands may be written to this register to set-up and execute, Erase, Erase Verify, Program, Program Verify and Reset modes. Each of these modes needs 2 cycles. Eah mode starts with a write operation to set-up the command, this is followed by either read or write operations. The device expects the first cycle be a write operation and does not corrupt data at any location in the memory. Read mode is set-up with one cycle only and may be followed by any number of read operations to output data. Electronic Signature Read mode is set-up with one cycle and followed by a read cycle to output the manufacturer or device codes.


Related products with the same datasheet
Some Part number from the same manufacture ST Microelectronics, Inc.
M28F101-150P6 1 Megabit -128k X 8, Chip Erase- Flash Memory
M28F101-150XK1 1 MB 128k X 8, Chip Erase Flash Memory
M28F101-200-1 1 Megabit -128k X 8, Chip Erase- Flash Memory
M28F101-200K1 1 MB 128k X 8, Chip Erase Flash Memory
M28F101A-100-1 1 Megabit -128k X 8, Chip Erase- Flash Memory

M27256-1F1 : NND - NMOS 256 Kbit (32KB X8) uv EPROM

PSD4235F1-A-12UI : Flash In-system-programmable Peripherals For 16-bit MCUs

PSD4235G3V-15JI : Flash In-system-programmable Peripherals For 16-bit MCUs

PSD935F3V-B-15B81 : Configurable Memory System on a Chip For 8-bit Microcontrollers

T1213NH : 800V Standard Triac

ST7PLITEU05M6TR : 8-bit MCU with Single Voltage Flash Memory, ADC, Timers

ST92F124CR1T6 : 8/16-bit Single Voltage Flash MCU Family WITH RAM, E3 Tm(emulated Eeprom), CAN 2.0B AND J1850 BLPD

STM6519ALARUB6F : Pmic - Supervisor Integrated Circuit (ics) Smart Reset Tape & Reel (TR) -; IC SMART RESET 6UDFN Specifications: Output: Open Drain or Open Collector ; Reset: Active Low ; Package / Case: 6-UDFN ; Packaging: Tape & Reel (TR) ; Number of Voltages Monitored: - ; Reset Timeout: Adjustable/Selectable ; Type: Smart Reset ; Voltage - Threshold: - ; Operating Temperature: -40C ~ 85C ; Lead Free

M95128-RCS6G/K : SPI BUS SERIAL EEPROM Specifications: Memory Category: PROM, EEPROM

5962-87615012X : AC SERIES, TRIPLE 3-INPUT NAND GATE, CDFP14 Specifications: Gate Type: NAND ; Supply Voltage: 3V ; Logic Family: CMOS ; Inputs: 3 ; Propagation Delay: 11 ns ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Pin Count: 14 ; IC Package Type: Other, CERAMIC, DFP-14

0-C     D-L     M-R     S-Z