Details, datasheet, quote on part number: M28F201-150K3TR
PartM28F201-150K3TR
CategoryMemory => Flash
Description2 MB 256k X 8, Chip Erase Flash Memory
CompanyST Microelectronics, Inc.
DatasheetDownload M28F201-150K3TR datasheet
Quote
Find where to buy
 
  

 

Features, Applications

10% SUPPLY VOLTAGE 12V PROGRAMMING VOLTAGE FAST ACCESS TIME: 70ns BYTE PROGRAMMING TIME: 10s typical ELECTRICAL CHIP ERASE in 1s RANGE LOW POWER CONSUMPTION Active Current: 15mA typical Stand-by Current: 10A typical 10,000 PROGRAM/ERASE CYCLES INTEGRATED ERASE/PROGRAM-STOP TIMER OTP COMPATIBLE PACKAGES and PINOUTS ELECTRONIC SIGNATURE Manufacturer Code: 20h Device Code: F4h DESCRIPTION The M28F201 FLASH Memory product is a nonvolatile memories which may be erased electrically at the chip level and programmed byte-by-byte. It is organised as 256K bytes. It uses a command register architecture to select the operating modes and thus provide a simple microprocessor interface. The M28F201 FLASH Memory product is suitable for applications where the memory has to be reprogrammed in the equipment. The access time of 70ns makes the device suitable for use in high speed microprocessor systems.

G W VPP VCC VSS April 1997 Address Inputs Data Inputs / Outputs Chip Enable Output Enable Write Enable Program Supply Voltage Ground

DEVICE OPERATION The M28F201 FLASH Memory product employs a technology similar a 2 Megabit EPROM but add to the device functionality by providing electrical erasure and programming. These functions are managed by a command register. The functions that are addressed via the command register depend on the voltage applied to the VPP, program voltage, input. When VPP is less than or equal to 6.5V, the command register is disabled and the M28F201 functions as a read only memory providing operating modes similar to an EPROM (Read, Output Disable, Electronic Signature Read and Standby). When VPP is raised to 12V the command register is enabled and this provides, in addition, Erase and Program operations. READ ONLY MODES, VPP 6.5V For all Read Only Modes, except Standby Mode, the Write Enable input W should be High. In the Standby Mode this input is 'don't care'. Read Mode. The M28F201 has two enable inputs, E and G, both of which must be Low in order to output data from the memory. The Chip Enable (E) is the power control and should be used for device selection. Output Enable (G) is the output control and should be used to gate data on to the output, independantof the device selection.

Symbol TA TSTG VIO VCC VA9 VPP Parameter Ambient Operating Temperature Storage Temperature Input or Output Voltages Supply Voltage A9 Voltage Program Supply Voltage, during Erase or Programming Value to 14 Unit C

Note: Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the SGS-THOMSON SURE Program and other relevant quality documents.

- DQ7 Data Output Hi-Z Codes Data Output Data Input Hi-Z
Output Disable Standby Electronic Signature Read
Notes: X = VIL or VIH. 2. Refer also to the Command table.
Identifier Manufacturer's Code Device Code A0 VIL VIH DQ0 0 Hex Data 20h F4h

 

Related products with the same datasheet
M28F201-120K1TR
M28F201-120K3R
M28F201-120K3TR
M28F201-120K6R
M28F201-120K6TR
M28F201-120N1R
M28F201-120N1TR
M28F201-120N3R
M28F201-120N3TR
M28F201-120N6R
M28F201-120N6TR
M28F201-120XK1R
Some Part number from the same manufacture ST Microelectronics, Inc.
M28F201-150K6R 2 MB 256k X 8, Chip Erase Flash Memory
M28F256 256k -32k X 8, Chip Erase- Flash Memory
M28F256-10B1TR 256k ( 32k X8, Chip Erase ) Flash Memory
M28F256-12-1 256k -32k X 8, Chip Erase- Flash Memory
M28F256-12B1TR 256k ( 32k X8, Chip Erase ) Flash Memory
M28F256-15-1 256k -32k X 8, Chip Erase- Flash Memory

M27512-F-1 : NND - NMOS 512 Kbit (64KB X8) uv EPROM

M27V160-100F6TR : 16 Mbit 2mb x8 or 1mb X16 Low Voltage uv EPROM And OTP EPROM

SM15T7V5AMDG : Transil->1.5kW Transil

ST19WR66 : Dual Contactless Smartcard MCU With Map, RF Uart, Iart & 66 Kbytes High Density EePROM

TL1431AC : Programmable Voltage Reference

M95256-RBN3P : 256 Kbit Serial SPI bus Eeprom with high Speed Clock

ULQ2801_08 : Eight Darlington Array

NAND04GW4B4DZL1F : 4gbit, 2112 Byte Page, 3V, Multi-level NAND Flash Memory

ST92F124CV1QC : 8/16-bit Single Voltage Flash MCU Family WITH RAM, E3 Tm(emulated Eeprom), CAN 2.0B AND J1850 BLPD

M95320-RDW3TG/B : 4K X 8 SPI BUS SERIAL EEPROM, PDSO8 Specifications: Density: 33 kbits ; Number of Words: 4 k ; Bits per Word: 8 bits ; Bus Type: Serial ; Production Status: Full Production ; Data Rate: 5 MHz ; Logic Family: CMOS ; Supply Voltage: 5V ; Package Type: 0.169 INCH, HALOGEN FREE AND ROHS COMPLIANT, TSSOP-8, TSSOP ; Pins: 8 ; Operating Rang

STRH100N6FSY3 : 48 A, 100 V, 0.035 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-254AA Specifications: Polarity: N-Channel ; MOSFET Operating Mode: Enhancement ; V(BR)DSS: 100 volts ; rDS(on): 0.0350 ohms ; Package Type: ROHS COMPLIANT, HERMETIC SEALED PACKAGE-3 ; Number of units in IC: 1

STEVAL-ISA176V1 : Power Management IC Development Tools 5V/1A optoless charger (CC/CV) using ALTAIR05T-800 STMicroelectronics ALTAIR05T-800 All-Primary-Sensing Switching Regulator is a high-voltage switcher intended for operating directly from the rectified mains with minimum external parts. It combines a high-performance low voltage PWM controller chip and an 800V avalanche-rugged power section in th

 
0-C     D-L     M-R     S-Z