|Description||256k -32k X 8, Chip Erase- Flash Memory|
|Company||ST Microelectronics, Inc.|
|Datasheet||Download M28F256 datasheet
FAST ACCESS TIME: 90ns LOW POWER CONSUMPTION Standby Current: 100µA Max 10,000 ERASE/PROGRAM CYCLES 12V PROGRAMMING VOLTAGE TYPICAL BYTE PROGRAMMING TIME 10µs (PRESTO F ALGORITHM) ELECTRICAL CHIP ERASE IN 1s RANGE INTEGRATED ERASE/PROGRAM STOP TIMER EXTENDED TEMPERATURE RANGES
Figure 1. Logic Diagram DESCRIPTION The M28F256 FLASH Memory Is a non-volatile memory which may be erased electrically at the chip level and programmed byte-by-byte. It is organised as 32K bytes of 8 bits. It uses a command register architecture to select the operating modes and thus provides a simple microprocessor interface. The M28F256 FLASH Memory is suitable for applications where the memory has to be reprogrammed in the equipment. The access time of 100ns makes the device suitable for use in high speed microprocessor systems.
G W VPP VCC VSS Address Inputs Data Inputs / Outputs Chip Enable Output Enable Write Enable Program Supply Voltage Ground
Symbol TA TSTG VIO VCC VA9 VPP Parameter Ambient Operating Temperature Storage Temperature Input or Output Voltages Supply Voltage A9 Voltage Program Supply Voltage, during Erase or Programming Value to 14 Unit °C
Note: Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the SGS-THOMSON SURE Program and other relevant quality documents.
DEVICE OPERATION The M28F256 FLASH Memory employs a technology similar a 256K EPROM but adds to the device functionality by providing electrical erasure and programming. These functions are managed by a command register. The functions that are addressed via the command register depend on the voltage applied to the VPP, program voltage,
input. When VPP is less than or equal to 6.5V, the command register is disabled and M28F256 functions as a read only memory providing operating modes similar to an EPROM (Read, Output Disable, Electronic Signature Read and Standby). When VPP is raised to 12V the command register is enabled and this provides, in addition, Erase and Program operations.Operation Read Output Disable Standby Electronic Signature
- DQ7 Data Output Hi-Z Codes Data Output Data Input Hi-Z
Identifier Manufacturer's Code Device Code A0 VIL VIH DQ0 0 Hex Data 20h 0A8h
READ ONLY MODES, VPP 6.5V For all Read Only Modes, except Standby Mode, the Write Enable input W should be High. In the Standby Mode this input is 'don't care'. Read Mode. The M28F256 has two enable inputs, E and G, both of which must be Low in order to output data from the memory. The Chip Enable (E) is the power control and should be used for device selection. Output Enable (G) is the output control and should be used to gate data on to the output, independant of the device selection. Standby Mode. In the Standby Mode the maximum supply current is reduced to 100µA. The device is placed in the Standby Mode by applying a High to the Chip Enable (E) input. When in the Standby Mode the outputs are in a high impedance state, independant of the Output Enable (G) input. Output Disable Mode. When the Output Enable (G) is High the outputs are in a high impedance state.
Electronic Signature Mode. This mode allows the read out of two binary codes from the device which identify the manufacturer and device type. This mode is intended for use by programming equipment to automatically select the correct erase and programming algorithms. The Electronic Signature Mode is active when a high voltage 13V) is appliedto address line A9 with E and G Low. With A0 Low the output data is the manufacturer code, when A0 is High the output is the device type code. All other address lines should be maintained Low while reading the codes. The electronic signature may also be accessed in Read/Write modes. READ/WRITE MODES, 11.4V VPP 12.6V When VPP is High both read and write operations may be performed. These are defined by the contents of an internal command register. Commands may be written to this register to set-up and execute, Erase, Erase Verify, Program, Program Verify and Reset modes. Each of these modes needs 2
|Related products with the same datasheet|
|Some Part number from the same manufacture ST Microelectronics, Inc.|
|M28F256-10 256k -32k X 8, Chip Erase- Flash Memory|
|M28F256-10B1TR 256k ( 32k X8, Chip Erase ) Flash Memory|
|M28F256-12-1 256k -32k X 8, Chip Erase- Flash Memory|
|M28F256-12B1TR 256k ( 32k X8, Chip Erase ) Flash Memory|
|M28F256-15-1 256k -32k X 8, Chip Erase- Flash Memory|
|M28F256-15B1TR 256k ( 32k X8, Chip Erase ) Flash Memory|
|M28F256-20-1 256k -32k X 8, Chip Erase- Flash Memory|
|M28F256-20B1TR 256k ( 32k X8, Chip Erase ) Flash Memory|
|M28F256A-10 256k -32k X 8, Chip Erase- Flash Memory|
|M28F512 512k -64k X 8, Chip Erase- Flash Memory|
|M28LV64 Obsolete - 64K (8K X 8) Low Voltage Parallel EePROM With Software Data Protection|
|M28LV64-200K1 64k 8k X 8 Low Voltage Parallel EePROM With Software Data Protection|
CMI9738_4CH : AC'97 Codec. Versatility 4CH AC97 CODEC, applicable for currently mainstream MB chipsets of Intel, VIA, Ali, and SIS. CMI9738 is ideal for PC2001-compliant desktops, notebooks, and home entertainment PCs where high-quality audio is a must. 4CH Playback The specially-designed 4CH hardware architecture of CMI9738 allows all types of south bridge to playback 4CH audio,.
PU17310 : . The PLUS17310 PLD is a high speed, combinatorial Programmable Logic Array. The Philips Semiconductors state-of-the-art Oxide Isolated Bipolar fabrication process is employed to produce maximum propagation delays 10ns or less. The 24-pin PLUS17310 device has a programmable AND array and a programmable OR array. Unlike PAL® devices, 100% product term.
LH4012K : Wideband Buffer.
1SMB33 : Zener Overvoltage Transient Suppressors.
EC33 : Oscillator. DATE: TO: FROM: RE: September 20th, 2006 All Sales Personnel Mark Stoner Product Termination To all concerned parties, This bulletin is to notify all customers of the discontinuation of the following Ecliptek series effective September 20th, 2006: Series EC33 2.5V 4 pad SMD Plastic Oscillator Recommended Replacement or EC37 In compliance with our End of Life.
CAT16-000F2 : Cat/cay 16 Series-chip Resistor Arrays. 5,000 pcs. per reel CAY16-J8) 4,000 pcs. per reel (CAT16-J8) Paper tape REV.03/15/04 s are subject to change without notice. Customers should verify actual device performance in their specific applications. .
4-1879064-7 : 1.5µF Tantalum Capacitor 2312 (6032 Metric) 50V; CAP TANT 1.5UF 50V 10% 2312. s: Capacitance: 1.5µF ; Voltage - Rated: 50V ; Tolerance: ±10% ; : General Purpose ; Operating Temperature: -55°C ~ 125°C ; Lead Spacing: - ; ESR (Equivalent Series Resistance): 1.500 Ohm ; Lifetime @ Temp.: - ; Mounting Type: Surface Mount ; Type: Molded ; Package / Case:.
1955460000 : Free Hanging (In-Line) Terminal Block - Headers, Plug And Socket Connectors, Interconnect Plug, Female Sockets; CONN PLUG TERM BLCK 5.00MM 13POS. s: Terminal Block Type: Plug, Female Sockets ; Positions Per Level: 13 ; Pitch: 0.197" (5.00mm) ; Number of Levels: 1 ; Header Orientation: - ; Plug Wire Entry: 180° ; Termination: Screw ; Wire Gauge: 12-26.
MS3102E18-1P : Aluminum, Olive Drab Cadmium Plated Panel Mount, Flange Circular Connectors, Interconnect Receptacle, Male Pins; CONN RCPT 10 POS BOX MNT W/PINS. s: Connector Type: Receptacle, Male Pins ; Shell Size - Insert: 18-1 ; Mounting Type: Panel Mount, Flange ; Fastening Type: Threaded ; : - ; Packaging: Bulk ; Number of Positions: 10 ; Termination: Solder.
GTC020R-20-14P : Olive Drab, Silver Plated Panel Mount, Flange; Through Hole Circular Connectors, Interconnect Receptacle, Male Pins; CONN RCPT 5POS BOX MNT W/PINS. s: Connector Type: Receptacle, Male Pins ; Shell Size - Insert: 20-14 ; Mounting Type: Panel Mount, Flange; Through Hole ; Fastening Type: Reverse Bayonet Lock ; : - ; Packaging: Bulk ; Number of Positions:.
RT0402FRE0716K5L : 16.5K Ohm 0.063W, 1/16W Chip Resistor - Surface Mount; RES 16.5K OHM 1/16W 1% SMD 0402. s: Resistance (Ohms): 16.5K ; Power (Watts): 0.063W, 1/16W ; Tolerance: ±1% ; Packaging: Tape & Reel (TR) ; Composition: Thin Film ; Temperature Coefficient: ±50ppm/°C ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant.
4-641237-4 : Gold Free Hanging (In-Line) Rectangular - Free Hanging, Panel Mount Connectors, Interconnect Receptacle; 14P MTA100 CONN ASSY RED 30AU. s: Color: Red ; Connector Type: Receptacle ; Contact Finish: Gold ; : Closed End ; Mounting Type: Free Hanging (In-Line) ; Number of Rows: 1 ; Pitch: 0.100" (2.54mm) ; Row Spacing: - ; Packaging: Bulk ; Fastening Type:.
M2GL050-FGG896 : IC FPGA 50K LUT W/TXRS 896-FPGA. s: Family: Embedded - FPGAs (Field Programmable Gate Array) ; Series: IGLOO2 ; Number of LABs/CLBs: - ; Number of Logic Elements/Cells: 56340 ; Total RAM Bits: 1869824 ; Number of I /O: 377 ; Number of Gates: - ; Voltage - Supply: 1.14 V ~ 1.26 V ; Mounting Type: Surface Mount ; Operating Temperature: 0°C ~ 85°C.
FI-B2012-102KJT : 1 ELEMENT, 1 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD. s: Mounting Option: Surface Mount Technology ; Devices in Package: 1 ; Core Material: Ferrite ; Lead Style: WRAPAROUND ; Application: General Purpose, RF Choke ; Inductance Range: 1 microH ; Inductance Tolerance: 10 (+/- %) ; DCR: 0.4000 ohms ; Rated DC Current: 50 milliamps ; Q Factor:.
GAL-1 : 0 MHz - 8000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER. s: Amplifier Type: Power Amplifier ; Applications: RF Microwave ; Frequency Range: 0.0 to 8000 MHz ; Minimum Gain: 9 dB ; Input VSWR: 1.8 1 ; Output VSWR: 1.8 1 ; Package Type: SOT-89, 3 PIN ; Nominal Impedance: 50 ; Operating Temperature: -45 to 85 C (-49 to 185 F).
252133 : PANEL MOUNT, BOARD TERMINATED, FEMALE, MCX CONNECTOR, SOLDER, RECEPTACLE. s: Connector Type: MCX ; Gender: Female ; Termination Types: SOLDER.
414352-1 : PANEL MOUNT, BOARD TERMINATED, FEMALE, BNC CONNECTOR, SOLDER, JACK. s: Connector Type: BNC ; Gender: Female ; Termination Types: SOLDER.
552R-01ILF : 200 MHz, OTHER CLOCK GENERATOR, PDSO20. s: Device Type: Clock Generator ; Bus Interface: CMOS ; Package Type: Surface Mount, SSOP, 0.150 INCH, ROHS COMPLIANT, SSOP-20 ; Supply Voltage: 3 to 5.5 volts ; Frequency: 27 MHz ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; / Standards: RoHS, Lead-Free.