Details, datasheet, quote on part number: M295V200T-120N3R
PartM295V200T-120N3R
CategoryMemory => Flash
Description2 Mbit 256kb x8 or 128kb X16, Boot Block Single Supply Flash Memory
CompanyST Microelectronics, Inc.
DatasheetDownload M295V200T-120N3R datasheet
  

 

Features, Applications
2 Mbit 128Kb x16, Boot Block) Single Supply Flash Memory

5V10% SUPPLY VOLTAGE for PROGRAM, ERASE and READ OPERATIONS FAST ACCESS TIME: 55ns FAST PROGRAMMING TIME 10s by Byte 16s by Word typical PROGRAM/ERASE CONTROLLER (P/E.C.) Program Byte-by-Byte or Word-by-Word Status Register bits and Ready/Busy Output MEMORY BLOCKS Boot Block (Top or Bottom location) Parameter and Main blocks BLOCK, MULTI-BLOCK and CHIP ERASE MULTI-BLOCK PROTECTION/TEMPORARY UNPROTECTION MODES ERASE SUSPEND and RESUME MODES Read and Program another Block during Erase Suspend LOW POWER CONSUMPTION Stand-by and Automatic Stand-by 100,000 PROGRAM/ERASE CYCLES per BLOCK 20 YEARS DATA RETENTION Defectivity below 1ppm/year ELECTRONIC SIGNATURE Manufacturer Code: 0020h Device Code, 00D3h Device Code, M29F200B: 00D4h DESCRIPTION The is a non-volatile memory that may be erased electrically at the block or chip level and programmed in-system on a Byte-by-Byteor Wordby-Word basis using only a single 5V VCC supply. For Program and Erase operations the necessary high voltages are generated internally. The device can also be programmed in standard programmers. The array matrix organisation allows each block to be erased and reprogrammed without affecting other blocks. Blocks can be protected against programing and erase on programming equipment, and temporarily unprotected to make changes in the application.

A0-A16 Address Inputs Data Input/Outputs, Command Inputs Data Input/Outputs Data Input/Output or Address Input Chip Enable Output Enable Write Enable Reset / Block Temporary Unprotect Ready/Busy Output Byte/Word Organisation Supply Voltage Ground

Parameter Ambient Operating Temperature Under Bias Storage Temperature Input or Output Voltages Supply Voltage

Notes: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not i mplied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Minimum Voltage may undershoot to 2V during transition and for less than 20ns. 3. Depends on range.

DESCRIPTION (Cont'd) Instructions for Read/Reset, Auto Select for reading the Electronic Signature or Block Protection status, Programming, Block and Chip Erase, Erase Suspend and Resume are written to the device in cycles of commandsto a Command Interfaceusing standard microprocessor write timings. The device is offered x 20mm) and SO44 packages. Both normal and reverse pinouts are available for the TSOP48 package. Organisation The M29F200 is organisedas 128K x16 bits selectable by the BYTE signal. When BYTE is Low the Byte-wide x8 organisation is selected and the address lines are DQ15A1 and A0-A16. The Data Input/Output signal DQ15A1 acts as address line A1 which selects the lower or upper Byte of the memory word for output DQ0-DQ7, DQ8-DQ14 remain at High impedan ce. When BYTE is High the memory uses the address inputs A0-A16 and the Data Input/Outputs DQ0-DQ15. Memory control is provided by Chip Enable E, Output Enable G and Write Enable W inputs. AReset/Block TemporaryUnprotection RP tri-level input provides a hardware reset when pulled Low, and when held High (at VID) temporarily unprotects blocks previously protected allowing them to be programed and erased. Erase and Program operations are controlled by an internal Program/Erase Controller (P/E.C.). Status Register data output on DQ7 provides a Data Polling signal, and DQ6 and DQ2 provide Toggle signals to indicate the state of

the P/E.C operations. A Ready/Busy RB output indicates the completion of the internal algorithms. Memory Blocks The devices feature asymmetrically blocked architecture providing system memory integration. Both M29F200T and M29F200B devices have an array of 7 blocks, one Boot Block of 16 KBytes or 8 KWords, two Parameter Blocks of 8 KBytes or 4 KWords, one Main Block of 32 KBytes or 16 KWords and three Main Blocks of 64 KBytes or 32 KWords. The M29F200T has the Boot Block at the top of the memory address space and the M29F200B locates the Boot Block starting at the bottom. The memory maps are showed in Figure 3. Each block can be erased separately, any combination of blocks can be specified for multi-block erase or the entire chip may be erased. The Erase operations are managed automatically by the P/E.C. The block erase operation can be suspended in order to read from or program to any block not being ersased, and then resumed. Block protection provides additional data security. Each block can be separately protected or unprotected against Program or Erase on programming equipment. All previously protected blocks can be temporarily unprotected in the application. Bus Operations The following operations can be performed using the appropriatebus cycles: Read (Array, Electronic Signature, Block Protection Status), Write command, Output Disable, Standby, Reset, Block Prot n , Unp t e cti on Verif y, Unprotection Verify and Block Temporary Unprotection. See Tables 4 and 5.


 

Related products with the same datasheet
M295V200T-120M1TR
M295V200T-120M3R
M295V200T-120M3TR
M295V200T-120M6R
M295V200T-120M6TR
M295V200T-120N1R
M295V200T-120N1TR
M295V200T-120N3TR
M295V200T-120N6R
M295V200T-120N6TR
M295V200T-55M1R
Some Part number from the same manufacture ST Microelectronics, Inc.
M295V200T-120N3TR 2 Mbit 256kb x8 or 128kb X16, Boot Block Single Supply Flash Memory
M295V400B-120M1R 4 Mbit 512kb x8 or 256kb X16, Boot Block Single Supply Flash Memory
M295V400BB45M1T

BULD1101E : High Voltage Fast-switching NPN Power Transistor

ST1394 : IPAD (Integrated Passive and Active Discretes)->IP IEEE1394 One Port Cable Termination Network With Esd Protection Diodes

STH8N80 : N-channel Enhancement Mode Power MOS Transistors

T820-700W : Snubberless Triac

STAC2932B : Transistors, Radio Frequency RF power transistors HF/VHF/UHF N-channel MOSFETs

STR731FV2T6 : Arm7tdmi 32-bit MCU with Flash, 3x CAN, 4 Uarts, 20 Timers, ADC, 12 Comm. Interfaces

PSD913F5-20UI : Flash In-system Programmable ISP Peripherals For 8-bit MCUs

SRT512-W41GE : 13.56 MHz Short-range Contactless Memory chip with 512-bit Eeprom and Anticollision Functions

STF11N52K3 : Fet - Single Discrete Semiconductor Product 10A 525V 30W Through Hole; MOSFET N-CH 525V 10A TO-220FP Specifications: Mounting Type: Through Hole ; FET Type: MOSFET N-Channel, Metal Oxide ; Drain to Source Voltage (Vdss): 525V ; Current - Continuous Drain (Id) @ 25 C: 10A ; Rds On (Max) @ Id, Vgs: 510 mOhm @ 5A, 10V ; Input Capacitance (Ciss) @ Vds: 1400pF @ 50V ; Power - Max: 30W ; Packaging: Tube

M24C08-WDS3TP/W : 1K X 8 I2C/2-WIRE SERIAL EEPROM, PDIP8 Specifications: Density: 8 kbits ; Number of Words: 1 k ; Bits per Word: 8 bits ; Bus Type: Serial ; Production Status: Full Production ; Data Rate: 0 MHz ; Supply Voltage: 5V ; Package Type: LEAD FREE, PLASTIC, DIP-8, DIP ; Pins: 8 ; Operating Range: AUTOMOTIVE ; Operating Temperature: -40 to 125 C

ST72F361AR7TCXE : 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP64 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 8 MHz ; ROM Type: Flash ; Supply Voltage: 4.5 to 5.5 volts ; I/O Ports: 50 ; Package Type: LFQP, Other, 10 X 10 MM, ROHS COMPLIANT, LQFP-64 ; Operating Range: Industrial ; Pin Count: 64 ; Operating Temperature: -40 to 85 C (-40 to 185 F) ; Feat

ST7FLITE39F2M3 : 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP16 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 8 MHz ; ROM Type: Flash ; Supply Voltage: 3 to 5.5 volts ; I/O Ports: 13 ; Package Type: CDIP, Other, 0.300 INCH, PLASTIC, DIP-16 ; Operating Range: Commercial ; Pin Count: 16 ; Operating Temperature: 0 to 70 C (32 to 158 F) ; Features: PWM

 
0-C     D-L     M-R     S-Z