Details, datasheet, quote on part number: PSD935F2-15UI
PartPSD935F2-15UI
CategoryMemory
DescriptionConfigurable Memory System on a Chip For 8-bit Microcontrollers
CompanyST Microelectronics, Inc.
DatasheetDownload PSD935F2-15UI datasheet
  

 

Features, Applications

to 4 Mbit of Primary Flash Memory (8 uniform sectors) 256Kbit Secondary Flash Memory (4 uniform sectors) to 64 Kbit SRAM Over 3,000 Gates of PLD: DPLD 52 Reconfigurable I/O ports Enhanced JTAG Serial Port Programmable power management High Endurance: ­ 100,000 Erase/Write Cycles of Flash Memory ­ 1,000 Erase/Write Cycles of PLD

This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice.

The PSD9XX series of Programmable Microcontroller (MCU) Peripherals brings In-System-Programmability (ISP) to Flash memory and programmable logic. The result is a simple and flexible solution for embedded designs. PSD9XX devices combine many of the peripheral functions found in MCU based applications: 4 Mbit of Flash memory A secondary Flash memory for boot or data Over 3,000 gates of Flash programmable logic 64 Kbit SRAM Reconfigurable I/O ports Programmable power management.

PSD935G2 The PSD935G2 device offers two methods to program PSD Flash memory while the PSD is soldered to a circuit board.

An IEEE 1149.1 compliant JTAG-ISP interface is included on the PSD enabling the entire device (both flash memories, the PLD, and all configuration) to be rapidly programmed while soldered to the circuit board. This requires no MCU participation, which means the PSD can be programmed anytime, even while completely blank. The innovative JTAG interface to flash memories is an industry first, solving key problems faced by designers and manufacturing houses, such as:

First time programming ­ How do I get firmware into the flash the very first time?
JTAG is the answer, program the PSD while blank with no MCU involvement.
Inventory build-up of pre-programmed devices ­ How do I maintain an accurate

count of pre-programmed flash memory and PLD devices based on customer demand? How many and what version? JTAG is the answer, build your hardware with blank PSDs soldered directly to the board and then custom program just before they are shipped to customer. No more labels on chips and no more wasted inventory.

Expensive sockets ­ How do I eliminate the need for expensive and unreliable

sockets? JTAG is the answer. Solder the PSD directly to the circuit board. Program first time and subsequent times with JTAG. No need to handle devices and bend the fragile leads.

Two independent flash memory arrays are included so the MCU can execute code from one memory while erasing and programming the other. Robust product firmware updates in the field are possible over any communication channel (CAN, Ethernet, UART, J1850, etc) using this unique architecture. Designers are relieved of these problems:

Simultaneous read and write to flash memory ­ How can the MCU program the

same memory from which it is executing code? It cannot. The PSD allows the MCU to operate the two flash memories concurrently, reading code from one while erasing and programming the other during IAP.

Complex memory mapping ­ How can I map these two memories efficiently?

A Programmable Decode PLD is embedded in the PSD. The concurrent PSD memories can be mapped anywhere in MCU address space, segment by segment with extremely high address resolution. As an option, the secondary flash memory can be swapped out of the system memory map when IAP is complete. A built-in page register breaks the MCU address limit.

Separate program and data space ­ How can I write to flash memory while it

resides in "program" space during field firmware updates, my 80C51 won't allow it The flash PSD provides means to "reclassify" flash memory as "data" space during IAP, then back to "program" space when complete. PSDsoft ­ ST's software development tool ­ guides you through the design process step-by-step making it possible to complete an embedded MCU design capable of ISP/IAP in just hours. Select your MCU and PSDsoft will take you through the remainder of the design with point and click entry, covering...PSD selection, pin definitions, programmable logic inputs and outputs, MCU memory map definition, ANSI C code generation for your MCU, and merging your MCU firmware with the PSD design. When complete, two different device programmers are supported directly from PSDsoft ­ FlashLINK (JTAG) and PSDpro. The PSD935G2 is available an 80-pin TQFP package. Please refer to the revision block at the end of this document for updated information.


 

Related products with the same datasheet
PSD935F1-12B81I
PSD935F1-12J
PSD935F1-12JI
PSD935F1-12M
PSD935F1-12MI
PSD935F1-12U
PSD935F1-12UI
PSD935F1-15B81
PSD935F1-15B81I
PSD935F1-15J
PSD935F1-15JI
PSD935F1-15M
Some Part number from the same manufacture ST Microelectronics, Inc.
PSD935F2-20B81 Configurable Memory System on a Chip For 8-bit Microcontrollers

FLC01-200H : Fire Lighter Circuit - (ASD)

M27C4002-45XB6X : 4 Mbit 256kb X16 uv EPROM And OTP EPROM

M54HC123D : Rad-hard Dual Retriggerable Monostable Multivibrator

M58WR064EB70ZB6 : 64 Mbit (4MB X 16, Multiple Bank, BURST) 1.8V Supply Flash Memory

PSD935F3V-90B81I : Configurable Memory System on a Chip For 8-bit Microcontrollers

M29W200BT55M1F : 2 Mbit (256kb x8 or 128kb x16, Boot Block) Low Voltage Single Supply Flash Memory

TSD4M150 : N-channel Enhancement MODE Isofet Power MOS Transistor Module

STPS20M100SG-TR : Diodes, Rectifier - Single Discrete Semiconductor Product 20A 100V Schottky; DIODE SCHOTTKY 100V 20A D2PAK Specifications: Diode Type: Schottky ; Voltage - DC Reverse (Vr) (Max): 100V ; Current - Average Rectified (Io): 20A ; Voltage - Forward (Vf) (Max) @ If: 850mV @ 20A ; Reverse Recovery Time (trr): - ; Current - Reverse Leakage @ Vr: 40ľA @ 100V ; Speed: Fast Recovery =< 500ns,>200mA (Io) ; Mounti

STPS2530CG : Diodes, Rectifier - Array Discrete Semiconductor Product 12.5A 30V Schottky; DIODE SCHOTTKY 30V 12.5A D2PAK Specifications: Diode Type: Schottky ; Diode Configuration: 1 Pair Common Cathode ; Voltage - DC Reverse (Vr) (Max): 30V ; Current - Average Rectified (Io) (per Diode): 12.5A ; Voltage - Forward (Vf) (Max) @ If: 530mV @ 12.5A ; Current - Reverse Leakage @ Vr: 1mA @ 30V ; Reverse Recovery Time (trr):

M95256-WMN3P/V : 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 Specifications: Density: 262 kbits ; Number of Words: 32 k ; Bits per Word: 8 bits ; Bus Type: Serial ; Production Status: Full Production ; Data Rate: 5 MHz ; Supply Voltage: 5V ; Package Type: 0.169 INCH, ROHS COMPLIANT, TSSOP-8, TSSOP ; Pins: 8 ; Operating Range: AUTOMOTIVE ; Operating Temperatur

SPC560P34L1BEFAX : RISC MICROCONTROLLER Specifications: Life Cycle Stage: ACTIVE

ST7PMC2S4T6 : IC,MICROCONTROLLER,8-BIT,ST72 CPU,QFP,44PIN,PLASTIC Specifications: Life Cycle Stage: ACTIVE

 
0-C     D-L     M-R     S-Z