|Category||Communication => Telephony => Line Card|
|Description||WLL & Isdn-ta Subscriber Line Interface Circuit|
|Company||ST Microelectronics, Inc.|
|Datasheet||Download STLC3055 datasheet
|Cross ref.||Similar parts: HC55185AIMZ|
MONOCHIP SLIC OPTIMISED FOR WLL & ISDN-TA APPLICATIONS IMPLEMENT ALL KEY FEATURES OF THE BORSHT FUNCTION SINGLE SUPPLY TO 15.8V) BUILT IN DC/DC CONVERTER CONTROLLER. SOFT BATTERY REVERSAL WITH PROGRAMMABLE TRANSITION TIME. ON-HOOK TRANSMISSION. PROGRAMMABLE OFF-HOOK DETECTOR THRESHOLD METERING PULSE GENERATION AND FILTER INTEGRATED RINGING INTEGRATED RING TRIP PARALLEL CONTROL INTERFACE (3.3V LOGIC LEVEL) PROGRAMMABLE CONSTANT CURRENT FEED SURFACE MOUNT PACKAGE INTEGRATED THERMAL PROTECTION TO +85°C OPERATING RANGE BLOCK DIAGRAM
DESCRIPTION The is a SLIC device specifically designed for WLL (Wireless Local Loop) and ISDNTerminal Adaptors. One of the distinctive characteristic of this device is the ability to operate with a single supply voltage (from to +15.8V) and self generate the negative battery by means an on chip DC/DC converter controller that drives an external MOS switch. The battery level is properly adjusted depending on the operating mode. A useful characteristic for
DESCRIPTION (continued) these applications is the integrated ringing generator. The control interface is a parallel type with open drain output and 3.3V logic levels. The metering pulses are generated on chip starting from two logic signals (0, 3.3V) one define the metering pulse frequency and the other the metering pulse duration. An on chip circuit then provides the proper shaping and filtering. Metering pulse amplitude and shaping (rising and decay time) can be programmed by external components. A dedicated cancellation circuit avoid posPIN CONNECTION
sible CODEC input saturation due to Metering pulse echo. Constant current feed can be set from to 40mA. Off-hook detection threshold is programmable from to 9mA. The device, developed in BCD100II technology (100V process), operates in the extended temperature range and integrates a thermal protection that sets the device in power down when Tj exceeds 140°C.
Parameter Positive Supply Voltage AGND to BGND Pin D1, D2, DET, CKTTX Max. junction Temperature Vbtot=|Vpos|+|Vbat|. (Total voltage applied to the device supply pins).
(1) Vbat is self generated by the on chip DC/DC converter and can be programmed via RF1 and RF2. RF1 and RF2 shall be selected in order to fulfil the a.m limits (see External Components Table page 10)
Symbol Vpos A/BGND Vdig Top Vbat (1) Positive Supply Voltage AGND to BGND Pin D1, D2, DET, CKTTX, PD Ambient Operating Temperature Range Self Generated Battery Voltage Parameter Value +85 -74 max. Unit °C VSymbol Rth j-amb Parameter Thermal Resistance Junction to Ambient Typ. Value 60 Unit °C/W
N. Name VPOS BGND AGND ZAC TX RX CAC ILTF TIP RING RLIM RTH IREF CREV Function Positive supply input ranging from to 15.8V. Battery Ground, must be shorted with AGND. Analog Ground, must be shorted with BGND. AC impedance synthesis. RX buffer output, the AC impedance is connected from this node to ZAC. Protection resistors image (the image resistor is connected from this node to ZAC). Balance Network for to 4 wire conversion (the balance impedance ZB is connected from this node to AGND. ZA impedance is connected from this node ZAC1). 4 wire output port (TX output). The signal is referred to AGND. If connected to single supply CODEC input it must be DC decoupled with proper capacitor. 4 wire input port (RX input); 300K input impedance. This signal is referred to AGND. If connected to single supply CODEC output it must be DC decoupled with proper capacitor. AC feedback input, AC/DC split capacitor (CAC). Transversal line current image output. 2 wire port; TIP wire (Ia is the current sourced from this pin). 2 wire port; RING wire (Ib is the current sunk into this pin). Constant current feed programming pin (via RLIM). RLIM should be connected close to this pin and PCB layout should avoid noise injection on this pin. Off-hook threshold programming pin (via RTH). RTH should be connected close to this pin and PCB layout should avoid noise injection on this pin. Internal bias current setting pin. RREF should be connected close to this pin and PCB layout should avoid noise injection on this pin. Reverse polarity transition time control. One proper capacitor connected between this pin and AGND is setting the reverse polarity transition time. This is the same transition time used to shape the "trapezoidal ringing" during ringing injection. DC feedback and ring trip input. RD should be connected close to this pin and PCB layout should avoid noise injection on this pin.
|Related products with the same datasheet|
|Some Part number from the same manufacture ST Microelectronics, Inc.|
|STLC3055N WLL & Isdn-ta Subscriber Line Interface Circuit|
|STLC3055Q WLL & Isdn-ta Subscriber Line Interface Circuit|
|STLC3065 WLL Subscriber Line Interface Circuit|
|STLC3080 Subscriber Line Interface Circuit|
|STLC30R80 Integrated Ringing Slic For Short Loop Applications|
|STLC5046 Programmable Four Channel Codec And Filter|
|STLC5048 Fully Programmable Four Channel Codec And Filter|
|STLC5411 2B1Q u Interface Device|
|STLC5412 2B1Q u Interface Device Enhanced With Dect Mode|
|STLC5412 2b1q u Interface Device Enhanced With Dect Mode|
|STLC5412FN 2B1Q u Interface Device Enhanced With Dect Mode|
|STLC5432 2MBIT Cept & Primary Rate Controller Device|
|STLC5432Q 2mbit Cept & Primary Rate Controller Device|
|STLC5444 Quad Feeder Power Supply|
M28F201-150N1R : 2 MB 256k X 8, Chip Erase Flash Memory
M36W832TE70ZA6T : 32 Mbit 2mb X16, Boot Block Flash Memory And 8 Mbit 512kb X16 SRAM, Multiple Memory Product
PSD835F2-70JI : Configurable Memory System on a Chip For 8-bit Microcontrollers
TS4974 : 1W Differential Audio Power Amplifier with Up/Down Digital Volume Control Pins At 3.3v, the TS4974 is a dual power audio amplifier capable of delivering 380mW of continuous RMS ouput power into a 8 bridgedtied loads with 1% THD+N. An external standby mode control reduces the supply current to less
M24C01-WBN6T : 16kbit, 8kbit, 4kbit, 2kbit and 1kbit Serial I2C Bus Eeprom
M24128-BFDW3TG : 256/128 Kbit Serial I©÷C Bus Eeprom Without Chip Enable Lines
M41T83ZQA6F : Clock/timing - Real Time Clock Integrated Circuit (ics) Clock/Calendar Tape & Reel (TR) 2.38 V ~ 5.5 V; IC RTC SERIAL W/BATT SW 16QFN Specifications: Date Format: YY-MM-DD-dd ; Time Format: HH MM SS hh (24 hr) ; Voltage - Supply: 2.38 V ~ 5.5 V ; Interface: I²C ; Memory Size: 7B ; Package / Case: 16-QFN ; Packaging: Tape & Reel (TR) ; Type: Clock/Calendar ; Operating Temperature: -40°C ~ 85°C ; Lead Free Status: Lead
LM293WPT : DUAL COMPARATOR, 9000 uV OFFSET-MAX, 1300 ns RESPONSE TIME, PDSO8 Specifications: Supply Voltage (VS): 5 volts ; Operating Temperature: -40 to 105 C (-40 to 221 F) ; Logic Output: O-COL ; Package Type: TSSOP, TSSOP-8 ; Number of Pins: 8 ; Number of Devices: 2
STD20NF10-1 : 25 A, 100 V, 0.045 ohm, N-CHANNEL, Si, POWER, MOSFET, TO-251AA Specifications: Polarity: N-Channel ; MOSFET Operating Mode: Enhancement ; V(BR)DSS: 100 volts ; rDS(on): 0.0450 ohms ; Package Type: ROHS COMPLIANT, TO-251, IPAK-3 ; Number of units in IC: 1
5962-8761701XX : AC SERIES, TRIPLE 3-INPUT NAND GATE, CDFP14 Specifications: Gate Type: NAND ; Supply Voltage: 3V ; Logic Family: CMOS ; Inputs: 3 ; Propagation Delay: 11 ns ; Operating Temperature: -55 to 125 C (-67 to 257 F) ; Pin Count: 14 ; IC Package Type: Other, CERAMIC, DFP-14
54LS42DMQB : Decimal Decoders. These BCD-to-decimal decoders consist of eight inverters and ten four-input NAND gates The inverters are connected in pairs to make BCD input data available for decoding by the NAND gates Full decoding of input logic ensures that all outputs remain off for all invalid (1015) input conditions Diode clamped inputs Also for applications as 4-line-to-16-line.
AT24C16SC : Smart Card/Secure Card. 2-wire Serial EePROM Smart Card Modules 16k (2048 X 8).
CS4297 : Crystalclear Soundfusion Audio Codec 97.
EM83110 : RF Keyboard Encoder.
EPD1600 : 8 Bit uc Based Data Processor ic For Use on Paim Top Devices.
FU-699PDF- : WDM->DWDM. Wavemonitor Integrated CW Light Sauce 25GHz Spacing 16ch Tunable, Wavelength=C-band, Output Power=20mW.
HFBR-2119T : Fiber Optic Transmitter And Receiver Data Links For 266 MBD. Fiber Optic Transmitter and Receiver Data Links for 266 MBd Technical Data Full Compliance with the Optical Performance Requirements of the Fibre Channel Physical Layer Other Versions Available for: - FDDI - ATM Compact 16-pin DIP Package with Plastic ST* Connector Wave Solder and Aqueous Wash Process Compatible Package Manufactured in an ISO 9001 Certified.
LC72348G-9970 : . The is a single chip controller designed unit : mm for portable stereo applications. 3231-QIP64G It incorporates / FM PLL tuner covering the frequency requirements in the USA, Europe, East Europe, and Japan. A 1/4 duty cycle, 1/2 bias LCD driver is also built in. 10 station memories in each of three bands: AM, FM II Integrated 1/4 duty cycle, 1/2 bias.
M68703HA : RF Power Module For 440-470MHz, 12.5V, 50W FM Mobile Radio. PIN: 1 Pin : RF INPUT 1st. DC SUPPLY 2nd. DC SUPPLY 3rd. DC SUPPLY : RF OUTPUT 6 GND: FIN ABSOLUTE MAXIMUM RATINGS (Tc=25°C unless otherwise noted) Symbol VCC ICC Pin (max) PO (max) TC (OP) Tstg Parameter Supply voltage Total current Input power Output power Operation case temperature Storage temperature Conditions ZG=ZL=50, VCC112.5V Ratings to +110.
MC10115 : Quad Line Receiver. The is a quad differential amplifier designed for use in sensing differential signals over long lines. The base bias supply (VBB) is made available at pin 9 to make the device useful as a Schmitt trigger, or in other applications where a stable reference voltage is necessary. Active current sources provide the MC10115 with excellent common mode noise.
MSC220AG : Ethernet Access and Switching Controllers. = Layer 3 Switching Controller ;; Package Type = N/a ;; No. Of Pins =.
S3078 : Multi-rate Limiting Amplifier And Clock Recovery Unit. SiGe BiCMOS Technology +3.3 V Power Supply Integrated Limiting Amplifier No Degradation in Jitter Tolerance down 5 mV Input Loss-of-Signal Detection Supports Clock Recovery for: OC-48 (2488.32 Mbps) with FEC OC-24 (1244.16 Mbps) with FEC OC-12 (622.08 Mbps) with FEC OC-3 (155.52 Mbps) with FEC NRZ data Gigabit Ethernet (GBE) (1250 Mbps) with FEC Fibre.
S558-5999-79 : LAN Magnetic. XFMR Module, 10/100Base-TX. Dual, two-port designs provide excellent EMI and common mode noise suppression Optimized for board layouts utilizing single row and dual stack RJ-45 connectors Operating temperature 70° C Meets all IEEE 802.3 standards including 350µH with 8mA bias Low profile, surface mount packaging rated 225° C peak IR reflow temperature Minimum interwinding breakdown.
SLE66C82P : Security & Chip Card Ics. 16-Bit Security Controller with Memory Management and Protection Unit 0.22 µm CMOS Technology 64-Kbyte ROM, 2304 bytes RAM, 8-Kbyte EEPROM 192-Bit DDES-EC2 Accelerator This document contains preliminary information on a new product under development. Details are subject to change without notice. Revision History: Current Version 11.02 Previous Releases:.
STB7104 : 0.1/2.5 GHZ si Mmic Buffer Amplifier. EXCELLENT ISOLATION LOW CURRENT CONSUMPTION ULTRA MINIATURE SOT323-6L PACKAGE x 0.8 mm) STB7102 HIGH ISOLATION @ 950 MHz) STB7103 HIGH LINEARITY (P1 dB OUTPUT = +1.5 dBm) STB7104 LOW CURRENT CONSUMPTION (2.8 mA) The STB7102, STB7103 and STB7104 designed for Mobile Phone applications (0.1/2.5GHz), are an high isolation Si MMIC Buffer Amplifiers. Manufactured.
TLK3114SBGNT : Gigabit Ethernet/Fibre Channel Transceivers. ti TLK3114SB, 10-Gbps Xaui Transceiver.