Details, datasheet, quote on part number: STLV3243EB
CategoryInterface and Interconnect => RS-232 (EIA-232)
DescriptionRS-232 Interface ICs
± 15 kV ESD protected 2.3 to 5.5 V, 400 kbps, RS-232 transceiver with auto-power-down
CompanyST Microelectronics, Inc.
DatasheetDownload STLV3243EB datasheet
Find where to buy


Features, Applications

ESD protection for RS-232 I/O pins: 8 kV IEC 1000-4-2 contact discharge 15 kV human body model 1 mA supply current achieved when in autopower-down 250 kbps minimum guaranteed data rate Guaranteed 6 V/ms slew rate range Guaranteed mouse drive ability 0.1 µF external capacitors Meet EIA/TIA-562 specifications Available in Flip-Chip28 package auto-power-down enabled, the device is automatically activated when a valid signal is applied to any receiver input. Typical applications are notebooks, PDAs, smartphones, hand-held equipment, palmtop computers, peripherals, battery-powered equipment, and printers.


The STLV3243EB device consists of 3 drivers, 5 receivers and a dual charge-pump circuit. All transmitter outputs and receiver inputs are protected ±8 kV USING IEC 1000-4-2 contact discharge and ±15 kV using the human body model. The receiver R2 is always active to implement a wake-up feature for serial port. The device is guaranteed to run at data rates of 250 kbps while maintaining RS-562 output levels. The auto-power-down feature operates when FORCEON is low and FORCEOFF is high. During this operation mode, if the device does not sense a valid RS-562 signal, the driver outputs are disabled. If FORCEOFF is set low, both drivers and receivers (expert R2B) are shut off, and supply current is reduced to 1 µA. Disconnecting the serial port or turning off the peripheral drives causes the auto-power-down condition to occur. Auto-power-down can be disabled when FORCEON and FORCEOFF are high, and this should be done when driving a serial mouse. With Table 1. Device summary

Pin configuration. 3 Maximum ratings. 5 Electrical characteristics. 6 Application circuit. 9 Timing diagrams. 10 Package mechanical data. 12 Revision history. 15

Symbol C1+ V+ VCC FORCEON R1OUT R3OUT Name and function Second receiver input voltage Third receiver input voltage Fourth receiver input voltage Fifth receiver input voltage First transmitter output voltage Second transmitter output voltage -5.5 V generated by the charge pump First receiver input voltage Third transmitter output voltage Third transmitter input voltage First transmitter input voltage Second transmitter input voltage Positive terminal of inverting charge pump capacitor Negative terminal of inverting charge pump capacitor Fourth receiver output voltage Fifth receiver output voltage Positive terminal of voltage- charge pump capacitor 5.5 V generated by the charge pump Supply voltage Drive high to override automatic circuitry keeping transmitters on (FORCEOFF must be high) First receiver output voltage Third receiver output voltage 3/16


Some Part number from the same manufacture ST Microelectronics, Inc.
TDA7493 Audio Power Amplifiers3 W + 3 W dual BTL class-D audio amplifier
TDA7590 Audio Processor ICs, DigitalDatasheet Digital signal processing IC for speech and audio applications
STA339BWS Sound Terminal >5V2.1-channel high-efficiency digital audio system
TDA7461 Car Entertainment ICsCar radio signal processor
L9935 Motor DriversTwo-phase stepper motor driver
L4949E Voltage RegulatorsDatasheet Multifunction very low drop voltage regulator
STV8172A Processors For DisplaysVertical deflection booster for 3 App TV/monitor applications with 70 V flyback generator
STV9325 Processors For DisplaysVertical deflection booster for 2.5 App TV/monitor applications with 70 V flyback generator
TEA3718 Integrated Power StagesStepper motor driver
M41T11 Serial Real-Time ClocksDatasheet Serial real-time clock with 56 bytes of NVRAM
STCL1100 Silicon OscillatorsSilicon Oscillators High frequency silicon oscillator family
EMIF01-TV02F3 EMI Filtering & Signal ConditioningSingle line IPAD\", EMI filter and ESD protection
STP24DP05 LED Driver (Power Logic)24-bit constant current LED sink driver with output error detection
ST6200C 8-bit Microcontrollers8-bit Microcontrollers 8-bit MCUs with A/D converter, two timers, oscillator safeguard & safe reset
ST6208C 8-bit MCUs With A/D Converter, Two Timers, Oscillator Safeguard & Safe Reset8-bit MCUs with A/D converter, two timers, oscillator safeguard & safe reset
UPSD3212A 8-bit MicrocontrollersFlash programmable system device with 8032 MCU with USB and programmable logic
UPSD3454E 8-bit MicrocontrollersTurbo Plus series Fast Turbo 8032 MCU with USB and programmable logic
VIPER16 AC-DC ConversionFixed frequency VIPer™ plus family
VIPER27 AC-DC ConversionOff-line high voltage converters
L6562AT PFC ControllersPFC Controllers Transition-mode PFC controller

74AC16541 : CMOS/BiCMOS->AC/ACT Family->Advanced High Speed CM 16-BIT Bus Buffer With 3-STATE Outputs (NON INVERTED)

M27C256B-90-6 : 256 Kbit (32KB X8) uv EPROM And OTP EPROM

LD39080PT-R : The LD39080 is a fast ultra low drop linear regulator which operates from 2.5V to 6V input supply. A wide range of output options are available. The low drop voltage, low noise, and ultra low quiescent current make it suitable for low voltage microprocessor and memory applications. The device

ST72321BR7-AUTO : Microcontrollers for Automotive 8-bit MCU for automotive with 32 to 60 Kbyte Flash/ROM, ADC, 5 timers, SPI, SCI, I2C interface

NAND04GW4B2CZL6F : 4gbit, 2112 Byte Page, 3V, Multi-level NAND Flash Memory

IRF840_02 : N-channel 500V - 0.75Ąř - 8A To-220 Powermesh˘âii Mosfet

SM15T7V5AY : Tv - Diode Circuit Protection 6.4V 1500W; TRANSIL 1500W 7.5V UNIDIR SMC Specifications: Package / Case: DO-214AB, SMC ; Packaging: Tape & Reel (TR) ; Polarization: Unidirectional ; Power (Watts): 1500W ; Voltage - Reverse Standoff (Typ): 6.4V ; Voltage - Breakdown: 7.13V ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant

M54HC390F1R : HC/UH SERIES, ASYN NEGATIVE EDGE TRIGGERED 3-BIT UP DECADE COUNTER, CDIP16 Specifications: Counter Type: BCD/Decade Counter ; Counter Category: Asynchronous ; Counter Direction: UP ; Supply Voltage: 4.5 ; Package Type: DIP, CERAMIC, DIP-16 ; Logic Family: CMOS, HC/UH ; Number of Pins: 16 ; Number of Stages (Bits): 3 bits ; Clock Frequency: 33 MHz ; Operating Temperature: -

M95640-RDW6TG/B : 8K X 8 SPI BUS SERIAL EEPROM, PDSO8 Specifications: Density: 66 kbits ; Number of Words: 8 k ; Bits per Word: 8 bits ; Bus Type: Serial ; Production Status: Full Production ; Data Rate: 5 MHz ; Logic Family: CMOS ; Supply Voltage: 5V ; Package Type: 0.169 INCH, HALOGEN FREE AND ROHS COMPLIANT, TSSOP-8, TSSOP ; Pins: 8 ; Operating Rang

ST72P321BR7T7 : 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64 Specifications: Life Cycle Stage: ACTIVE ; Clock Speed: 16 MHz ; ROM Type: MROM ; Supply Voltage: 3.8 to 5.5 volts ; I/O Ports: 48 ; Package Type: LFQP, Other, 10 X 10 MM, ROHS COMPLIANT, PLASTIC, LQFP-64 ; Operating Range: Auto ; Pin Count: 64 ; Operating Temperature: -40 to 125 C (-40 to 257 F) ;

5962-8512702XX : HC/UH SERIES, ASYN NEGATIVE EDGE TRIGGERED 12-BIT UP BINARY COUNTER, CDFP16 Specifications: Counter Type: BINARY COUNTER ; Counter Category: Asynchronous ; Counter Direction: UP ; Supply Voltage: 4.5 ; Package Type: CERAMIC, FP-16 ; Logic Family: CMOS, HC/UH ; Number of Pins: 16 ; Number of Stages (Bits): 12 bits ; Clock Frequency: 22 MHz ; Operating Temperature: -55 to 125

Same catergory

422COR : Two Channel Rs-232 to Rs-422 Converter. This to RS-422 converter converts unbalanced RS-232 signals to balanced RS-422 signals. The RS-422 Standard uses a balanced voltage digital interface to allow communications of 90K bits per second on cable lengths of 4000 feet. Ten receivers can be connected to any one driver for use in multi-drop systems. The RS-232 port uses a female DB25 type of connector.

EL7232C : Dual Channel, High-Speed, High-current Line Driver With 3-State. Dual Channel High Speed High Current Line Driver w 3-State 3-State output 3V and 5V input compatible Clocking speeds to 10 MHz 20 ns Switching delay time 2A Peak drive Low matched output impedance 5X Low quiescent current 5 mA Wide operating voltage 4 5V--16V The EL7232C 3-state drivers are particularly well suited for ATE and microprocessor based applications.

GT-1B : Gt-1x Series Are Small Gifts That CAN be Used as Mini Torches. GT-1X Series are small gifts that can be used as mini torches. They can give out ultraviolet radiation and purple light. It can be used to recognise some kind of counterfeit money. GT-1R has a pink appearance. GT-1B has a blue appearance. GT-1W has a silvery white appearance. GT-1Y has a yellow appearance. Power Dissipation @ Ta=25°C Forward Current,.

LB1241 : Flourescent Display Tube Driver. The LB1241 has been designed for interfacing low-level digital devices to fluorescent display tubes. Its 8-circuit independent Darlington output stage is used for digit and segment drivers. Equivalent pull-down resistors are built in ; externally connected resistors to prevent ghosts are no longer required. Output is activated when input voltages are at a low level,.

LB1661 : 2-phase Unipolar Brushless Motor Driver. Applications . Output current 1.5 A. On-chip output protect zener diodes (LB1660N,. 1664N) stage withstand voltage: (LB1661, 1665). Output On-chip hall input amplifier. On-chip protector against lock. With lock detect pin SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534.

MCCS142238 : 18-bit Switchable Active Scsi-2 Bus Terminator (110 Ohms) With Voltage Regulator And Inverted Disconnect.

NJU3719 : 24 Bit Serial to Parallel Converter.

SLA24C04-D : 4 Kbit 512 X 8 Bit Serial CMOS EePROMs, I2c Synchronous 2-wire Bus. SLx 24C04 4 Kbit × 8 bit) Serial CMOS-EEPROM with I2C Synchronous 2-Wire Bus SLx 24C04 Revision History: Previous Version: Page (in previous (in current Version) Current Version: 1998-07-27 06.97 Subjects (major changes since last revision) Text was changed to "Typical programming time 5 ms for to 16 bytes". CS0, CS1 and CS2 were replaced by n.c. The paragraph.

SN65LVDS348D : ti SN65LVDS348, Quad LVDS Receiver With -4 to 5V Common-mode Range. TIA/EIA-644A Standard Single-Channel Signaling to 560 Mbps 5 V Common-Mode Input Voltage Range Flow-Through Architecture Active Failsafe Assures a High-level Output When an Input Signal Is not Present SN65LVDS348 Provides a Wide Common-Mode Range Replacement for the SN65LVDS048A or the DS90LV048A APPLICATIONS D Logic Level Translator D Point-to-Point.

SN65MLVD201 : . D Low-Voltage Differential to 55- Line D Type-1 Receivers Incorporate mV of D Cellular Base Stations D Central-Office Switches D Network Switches and Routers The 203, 206, and 207 are multipoint-low-voltage differential (M-LVDS) line drivers and receivers, which are optimized to operate at signaling rates to 200 Mbps. All parts comply with the multipoint.

SN751177N : ti SN751177, Dual Differential Driver/receiver Pairs. Meet or Exceed the Requirements of ANSI Standards TIA/EIA-422-B and TIA/EIA-485-A and ITU Recommendations V.10 and V.11 Designed for Multipoint Bus Transmission on Long Bus Lines in Noise Environments Driver Positive- and Negative-Current Limiting Thermal Shutdown Protection Driver 3-State Outputs Receiver Common-Mode Input Voltage Range 12 V Receiver.

SN754410NE : ti SN754410, Quadruple Half-h Drivers. 1-A Output-Current Capability Per Driver Applications Include Half-H and Full-H Solenoid Drivers and Motor Drivers Designed for Positive-Supply Applications Wide Supply-Voltage Range 36 V TTL- and CMOS-Compatible High-Impedance Diode-Clamped Inputs Separate Input-Logic Supply Thermal Shutdown Internal ESD Protection Input Hysteresis Improves Noise Immunity.

SN75C1406D : ti SN75C1406, Triple Low-power Drivers And Receivers. Meet or Exceed the Requirements of TIA/EIA-232-F and ITU Recommendation V.28 Very Low Power Consumption. 5 mW Typ Wide Driver Supply Voltage Range. ±15 V Driver Output Slew Rate Limited to 30 V/µs Max Receiver Input Hysteresis. 1000 mV Typ Push-Pull Receiver Outputs On-Chip Receiver 1-µs Noise Filter Functionally Interchangeable With Motorola MC145406.

TD62064BP-1 : Package = DIP16 ;; Function = 4ch. Darlington Sink Driver ;; Rating = 80V / 1.5A.

V300PSC : PCI Controllers. First Generation Pci System Controller. V3 Semiconductor makes no warranties for the use of its products. V3 does not assume any liability for errors which may appear in this document, however, we will attempt to notify customers of such errors. V3 Semiconductor retains the right to make changes to either the documentation, or component without notice. Please verify with V3 Semiconductor.

LTC4311 : Low Voltage I2C/SMBus Accelerator The LTC4311 is a dual I2C active pull-up designed to enhance data transmission speed and reliability for bus loading conditions well beyond the 400pF I2C limit. The LTC4311 operates at supply voltages from 1.6V to 5.5V and is also compatible with SMBus. The LTC4311 allows multiple device connections or a longer, more.

0-C     D-L     M-R     S-Z