Details, datasheet, quote on part number: STLVDS31BTR
PartSTLVDS31BTR
CategoryInterface and Interconnect
DescriptionHigh Speed Differential Line Drivers
CompanyST Microelectronics, Inc.
DatasheetDownload STLVDS31BTR datasheet
Cross ref.Similar parts: SN65LVDS31PW, DS90LV031ATMTC/NOPB, AM26C31, AM26C31-EP, AM26C31M, AM26C32, AM26C32-EP, AM26C32M, AM26LS31, AM26LS31M
Quote
Find where to buy
 
  

 

Features, Applications

MEETS OR EXCEEDS THE REQUIREMENTS OF ANSI TIA/EIA-644 STANDARD LOW VOLTAGE DIFFERENTIAL SIGNALING WITH TYPICAL OUTPUT VOLTAGE OF 350mV AND A 100 LOAD TYPICAL OUTPUT VOLTAGE RISE AND FALL TIMES 750ps (400Mbps) TYPICAL PROPAGATION DELAY TIMES OF 1.7ns OPERATES FROM A SINGLE 3.3V SUPPLY POWER DISSIPATION 25mW TYPICAL PER DRIVER AT 200MHz DRIVER AT HIGH IMPEDANCE WHEN DISABLED OR WITH VCC =0V PIN COMPATIBLE WITH THE AM26LS31, SN65LVD31 LOW VOLTAGE TTL (LVTTL) LOGIC INPUT LEVELS

DESCRIPTION The is a quad differential line drivers that implements the electrical characteristics of low voltage differential signaling (LVDS). This signaling technique lowers the output voltage levels of 5V differential standard levels (such TIA/EIA-422B) to reduce the power, increase the switching speeds and allows operations with a ORDERING CODES

3.3V supply rail. Any of the four current mode drivers will deliver a minimum differential output voltage magnitude of 247mV into a 100 load when enabled. The intended application of this device and signalling technique is for point-to-point baseband data transmission over controlled impedance media approximately 100. The transmission media may be printed circuit board traces, backplanes or cables. The ultimate rate and distance of data transfer is dependent upon the attenuation characteristics of the media and noise coupling to the environment. The STLVDS31 is characterized for operation from to 85C.

Package SO-16 (Tube) SO-16 (Tape & Reel) TSSOP16 (Tape & Reel)
Comments 50parts per tube / 20tube per box 2500 parts per reel 2500 parts per reel

PlN N SYMBOL 4Z G GND VCC Driver Inputs Driver Outputs Driver Outputs Enable Ground Supply Voltage NAME AND FUNCTION

L=Low level, H=High Level, X=Don't care, Z= High Impedance

Symbol VCC VI Tstg Supply Voltage (Note 1) DC Input Voltage Storage Temperature Range Parameter Value -0.5 to (VCC to +150 Unit V C

Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. Note 1: All voltages except differential I/O bus voltage, are with respect to the network ground terminal.

Symbol VCC VIH VILI TA Supply Voltage HIGH Level Input Voltage LOW Level Input Voltage Operating Temperature Range -40 Parameter Min. Typ. 3.3 Max. 3.6 Unit V C


 

Related products with the same datasheet
STLVDS31BD
STLVDS31BDR
Some Part number from the same manufacture ST Microelectronics, Inc.
STLVDS32 High Speed Differential Line Receivers
STLVDS32B
STLVDS3486B
STLVDS3487AD
STLVDS3487B High Speed Differential Line Drivers
STLVDS385 3.3V Programmable LVDS Transmitter 24-BIT Flat Panel Display (FPD) LINK-85MHZ
STLVDS385B +3.3V Programmable LVDS Transmitter 24-BIT Flat Panel Display (FPD) LINK-85MHZ
STLVDS385B High Speed Flat-panel Display Interface
STLVDS385BTR 3.3V Programmable LVDS Transmitter 24-BIT Flat Panel Display (FPD) LINK-85MHZ
STLVDS47 3v LVDS Quad CMOS Differential Line Driver
STLVDS47B 3V LVDS Quad CMOS Differential Line Driver
STLVDS9637B High Speed Differential Line Receivers
STM1001 Reset Circuit
STM1645-10 RF Power Module Satellite Communications Applications
STM1645-30
STM2DPFS30L P - Channel 30v - 0.145ohm - 2a Minis0-8 StripFET MOSFET Plus Schottky Rectifier
STM351-2 RF Power Module Wireless Local Loop Applications
STM376-2
STM6316 DVD Optical Disc - Integrated Solution For DVD Players
STM690 3V Supervisor With Battery Switchover
STM690A 5V Supervisor With Battery Switchover
 
0-C     D-L     M-R     S-Z