Details, datasheet, quote on part number: STLVDS47B
PartSTLVDS47B
CategoryInterface and Interconnect
Description3V LVDS Quad CMOS Differential Line Driver
CompanyST Microelectronics, Inc.
DatasheetDownload STLVDS47B datasheet
  

 

Features, Applications
3V LVDS QUAD CMOS DIFFERENTIAL LINE DRIVER

>400 MBPS (200MHZ) SWITCHING RATES FLOW-THROUGH PINOUT SIMPLIFIES PCB LAYOUT 300ps (MAX.) DIFFERENTIAL SKEW 1.8 ns (TYP.) PROPAGATION DELAY 3.3V POWER SUPPLY DESIGN 350 mV DIFFERENTIAL SIGNALING LOW POWER DISSIPATION AT 3.3V STATIC IN TRISTATE) INTEROPERABLE WITH EXISTING 5V LVDS RECEIVERS HIGH IMPEDANCE ON LVDS OUTPUT ON POWER DOWN CONFORMS TO TIA/EIA-644 LVDS STANDARD INDUSTRIAL OPERATING TEMPERATURE RANGE TO +85 C) AVAILABLE IN SURFACE MOUNT (SOIC) AND LOW PROFILE TSSOP PACKAGE

DESCRIPTION The is a quad CMOS flow-through differential line driver designed for applications requiring ultra low power dissipation and high data rate. The device is designed to support data rates in excess 400Mbps (200 MHz) utilizing Low Voltage Differential Signaling (LVDS) techology. The STLVDS47 accepts low voltage TTL/CMOS input levels and translates them to low voltage ORDERING CODES

(350 mV) differential output signals. In addition, the driver support a TRI-STATE function that may be used to disable the output stage, disabling the load current, and thus dropping the device to an ultra low idle power state of 1.3mW typical. The STLVDS47 has a flow-through pinout for easy PCB layout. The EN and EN* inputs are ANDed together and control the TRI-STATE output. The STLVDS47 and companion line receiver (STLVDS48) provide a new alternative to high power pseudo-ECL devices for high-speed point-to-point interface applications.

Comments 50 parts per tube / 20 tube per box 2500 parts per reel 2500 parts per reel

PlN N SYMBOL DIN1 DIN2 VCC GND DIN3 DIN4 EN* DOUT1+ DOUT1Enable First Driver Input Second Driver Input Supply Voltage GROUND Third Driver Input Fourth Driver Input Enable (inverting) Fourth Driver Inverting Output Fourth Driver non-Inverting Output Third Driver non-Inverting Output Third Driver Inverting Output Second Driver Inverting Output Second Driver non-Inverting Output First Driver non-Inverting Output First Driver Inverting Output NAME AND FUNCTION

Symbol VCC DIN EN, EN* DOUT+,DOUTISCTOUT Tstg Supply Voltage Input Voltage Enable Input Voltage Output Voltage Short Circuit Duration Storage Temperature Range Parameter Value to 3.9 Continuous +150 C Unit

Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied.

Symbol VCC VIH VIL TA Supply Voltage High-Level Input Voltage Low-Level Input Voltage Operating Free-Air Temperature -40 Parameter Min TYP 3.3 Max 3.6 Unit V C


 

Related products with the same datasheet
STLVDS47BD
STLVDS47BDR
STLVDS47BTR
Some Part number from the same manufacture ST Microelectronics, Inc.
STLVDS47BD 3V LVDS Quad CMOS Differential Line Driver
STLVDS9637B High Speed Differential Line Receivers
STM1001 Reset Circuit
STM1645-10 RF Power Module Satellite Communications Applications
STM1645-30
STM2DPFS30L P - Channel 30v - 0.145ohm - 2a Minis0-8 StripFET MOSFET Plus Schottky Rectifier
STM351-2 RF Power Module Wireless Local Loop Applications
STM376-2
STM6316 DVD Optical Disc - Integrated Solution For DVD Players
STM690 3V Supervisor With Battery Switchover
STM690A 5V Supervisor With Battery Switchover
STM690RM6E 3V Supervisor With Battery Switchover
STM705 5V Supervisor
STM706 3V Supervisor
STM707 5V Supervisor
STM708 3V Supervisor
STM795 3V Supervisor With Battery Switchover
STM7E1 7 e 1 Channels Switch Array
STM7E1A
STm8000 Dvd-recorder Market With System-on-chip Solution
STM802 Solenoid Controller ic
Same catergory

485LP9TBN : Port Powered Rs-232 to Rs-485 Converter. The is a port-powered two-channel to RS-485 converter. It converts TD and RD RS-232 lines to balanced RS-485 signals. The unit can be powered from the RS-232 handshake lines, DTR and RTS. One of these handshakes must be high (asserted) to power the unit (See Table 1). DTR must be asserted to receive data. The RS-485 driver is enabled when RTS is asserted.

5962-9762201Q2A : ti SN55LVDS32, Quad LVDS Receiver. Meet or Exceed the Requirements of ANSI TIA/EIA-644 Standard Operate With a Single 3.3-V Supply Designed for Signaling Rate to 400 Mbps Differential Input Thresholds 100 mV Max Typical Propagation Delay Time 2.1 ns Power Dissipation 60 mW Typical Per Receiver at 200 MHz Bus-Terminal ESD Protection Exceeds 8 kV Low-Voltage TTL (LVTTL) Logic Output Levels.

DS92CK16 : Bus LVDS Tranceivers and Repeaters. DS92CK16 - 3V BLVDS 1 to 6 Clock Buffer/bus Transceiver, Package: Tssop, Pin Nb=24.

eKK8301 : Keyboard Controller.

FW323 : 1394a Pci Phy/link Opebl-host Controller Interface.

ILX485 : Interface ic. General The ILX485 is low-power transceivers for RS-485 and RS422 communication. IC contains one driver and one receiver. The driver slew rates of the ILX485 is not limited, allowing them to transmit to 2.5Mbps. These transceivers draw between 120A and 500A of supply current when unloaded or fully loaded with disabled drivers. All parts operate from.

ITI8000 : CompactPCI. Series Compactpci Multifunction Adapters User's Guide V1.0 12/01.

LC895194 : Cd-rom Error Correction Lsi With On-chip Atapi (IDE) Interface. CD-ROM Error Correction LSI with On-Chip ATA-PI (IDE) Interface CD-ROM error detection and correction, ATA-PI (IDE) interface (including the register and other blocks) ATA-PI (IDE) interface Supports 16-speed playback (with IORDY): Using 70 ns DRAMs 16.6 MB/s transfer rate: Using 70 ns DRAMs Supports the use of from M of buffer RAM. (DRAM) Allows the user.

M54977P : Latched/Addressable. Bi-cmos 12-bit Serial-input Latched Driver. The is a semiconductor integrated circuit fabricated using Bi-CMOS technology. It contains a serial input to serial/parallel output 12-bit CMOS shift register and CMOS latch as well as bipolar 12-bit parallel-output driver. Clock Serial input T 1 S-IN 11 O10 Parallel outputs q Serial input to serial/parallel output q Cascade connections possible through.

M56693FP : Latched/Addressable. Bi-cmos & Dmos 32-bit Serial-input Latched Driver.

SN54BCT543FK : Octal Registered Transceivers With 3-state Outputs. State-of-the-Art BiCMOS Design Significantly Reduces ICCZ 3-State True Outputs Back-to-Back Registers for Storage ESD Protection Exceeds 2000 V Per MIL-STD-883C, Method 3015 Package Options Include Plastic Small-Outline Packages (DW), Ceramic Chip Carriers (FK) and Flatpacks (W), and Plastic and Ceramic 300-mil DIPs (JT, NT) The BCT543 octal transceiver.

SN55121 : Dual Line Driver: 2 Drivers. The SN55121 and SN75121 dual line drivers are designed for digital data transmission over lines having impedances from to 500. They are also compatible with standard TTL logic and supply-voltage levels. The low-impedance emitter-follower outputs of the SN55121 and SN75121 can drive terminated lines such as coaxial cable or twisted pair. Having the outputs.

SN75150D : ti SN75150, Dual Line Driver. Meets or Exceeds the Requirement of TIA/EIA-232-F and ITU Recommendation V.28 Withstands Sustained Output Short Circuit to Any Low-Impedance Voltage Between 25 V and V 2-s Maximum Transition Time Through the 3-V Transition Region Under Full 2500-pF Load Inputs Compatible With Most TTL Families Common Strobe Input Inverting Output Slew Rate Can Be Controlled.

SN75172 : Rs485/422a Quad Line Driver With 3-state Outputs: 4 Drivers. Meets or Exceeds the Requirements of ANSI Standards EIA/TIA-422-B and RS-485 and ITU Recommendation V.11 Designed for Multipoint Transmission on Long Bus Lines in Noisy Environments 3-State Outputs Common-Mode Output Voltage Range 12 V Active-High and Active-Low Enables Thermal Shutdown Protection Positive- and Negative-Current Limiting Operates From.

SN75188 : Rs232 Quad Line Driver (mc1488n): 4 Drivers. Meet or Exceed the Requirements of ANSI EIA/ TIA-232-E and ITU Recommendation V.28 Designed to Be Interchangeable With Motorola MC1488 Current-Limited Output: 10 mA Typical Power-Off Output Impedance: 300 Minimum Slew Rate Control by Load Capacitor Flexible Supply Voltage Range Input Compatible With Most TTL Circuits The MC1488, SN55188, and SN75188.

TFB2010MHSB : Standard Line Circuits. ti TFB2010, Futurebus+ Arbitration Bus Controller.

UDN2544 : . Combining logic gates and high-current bipolar outputs, the UDN2544B quad Darlington power driver provides an interface between low-level logic circuitry and high-power loads. Each of the four outputs can sink A in the on state with peak inrush currents 2.5 A. The four power outputs are each comprised of an opencollector Darlington driver and an internal.

UPD72870 : Ieee1394 1-chip Ohci Host Controller. The PD72870, 72871 are the LSIs which integrated OHCI-Link and PHY function into a single chip. The PD72870, 72871 comply with the P1394a draft 2.0 s and the OpenHCI IEEE1394 1.0 and work to 400 Mbps. These make design so compact for PC and PC card application. Compliant with Link Layer Services as defined in 1394 Open Host Controller Interface release.

 
0-C     D-L     M-R     S-Z