|
|
Part: CXOMOSCILLATOR
Category:
Timing Circuits
-> Oscillators
-> Crystal/Quartz Oscillators
-> Crystal Oscillators
Description: 1.25 MHZ to 100 MHZ Ultra-low Profile (1.3mm) Miniature Surface Mount Crystal_oscillator
Company: Statek Corporation
Datasheet: Download CXOMOSCILLATOR datasheet File size : 186 kB
Request For quote: Find where to buy CXOMOSCILLATOR
Datasheet text preview:
CXOM OSCILLATOR
1.25 MHz to 120 MHz
TM
Ultra-Low Profile (1.3mm) Miniature Surface Mount Crystal Oscillator
DESCRIPTION
Statek's surface-mount CXOM oscillator consists of a TTL and CMOS compatible hybrid circuit and a STATEK miniature quartz crystal in an ultra-low profile ceramic package with one of the smallest footprints available in the industry.
FEATURES
Designed for surface mount applications using infrared, vapor phase, wave solder or epoxy mount techniques TTL and CMOS compatible Low power consumption Optional Tri-State or Output Enable Low EMI emission High shock resistance Full military testing available Hermetically sealed ceramic package
APPLICATIONS
A
TOP
GM M 4.19
actual size
side view
PACKAGE DIMENSIONS
D
2
BOTTOM
3
Industrial, Computer & Communications General purpose clock oscillator PCMCIA (FAX, Modem and LAN) Smart Card PDA and notebook computers Military & Aerospace Airborne hybrid computer Military high speed modem MCM
DIM A B C*
SUGGESTED LAND PATTERN
.067(1.70) .070(1.78)
1
4
D
B
C
E
TYP. INCHES 0.256 0.197 0.051 0.055 0.060 mm 6.50 5.00 1.30 1.40 1.52 0.070 0.263 0.204 0.055
MAX. INCHES mm 6.68 5.18 1.40 1.78
D E
Termination material is Au over Ni (SMI), solder dip (SM3) also available. *SMI termination; SM3 = 0.063 in. (1.60 mm) Max.
.065(1.65)
.201(5.11)
.136(3.45)
. 37(3.48) 1
GRID PLACEMENT COURTYARD
10116 - Rev C
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS
Specifications are typical at 25oC unless otherwise noted. Specifications are subject to change without notice. Supply Voltage Calibration Tolerance* Frequency Stability**
_ 5V + 10% (3V available)
Supply Voltage VDD -0.5V to 7.0V Storage Temperature -55OC to +125OC Maximum Process Temperature 260OC, 10 seconds
TRUTH TABLE
A: B: C:
O O
+ _ + _ + _
0.01% (100ppm) 0.1% 1.0%
+ _ + _ + _
PIN 1* CXOM-10E Low (0) High (1) CXOM-10T CXOM-10N Low (0) High (1) NC
* Normally high (internal pull-up resistor)
PIN 3 High (Z) Freq. Output High (Z) Freq. Output Freq. Output
_ 0O C to + 50OC from + 5 to
30ppm 50ppm 100ppm
-10 C to +70 C from 10 to
O
O
+ _
-40 C to +85 C from 20 to 100ppm -55OC to +125OCfrom Supply Current 14 mA for 50 MHz 12 mA for 40 MHz 10 mA for 30 MHz 8 mA for 24 MHz TTL Load CMOS Load Start-up Time Rise/Fall Time Duty Cycle Aging, first year Shock, survival*** Vibration survival 10 @ 5V 15 pF (up to 50 pF available) 5 msec. MAX. 3 nsec. Typ., 6 nsec. MAX. 40% Min., 60% MAX. 10 ppm MAX. 3,000g peak 0.3 msec., 1/2 sine 20g rms 10-2000 Hz random
+ _
+ _
30 to
+ _
ENABLE VS. TRI-STATE
Enable: When pin 1 is low (0), the oscillator stops oscillation. Tri-state: When pin 1 is low, the oscillator is running. However, the output buffer amplifier stops functioning and output is in high impedance (Z) state. Enable Current consumption when pin 1 is low Output recovery delay when pin 1 changes from low (0) to high (1) Low Delayed Tri-state High Immediate
Operating Temperature -10OC to +70OC Commercial -40OC to +85OC Industrial -55OC to +125OC Military
* Tighter tolerances available ** Does not include calibration tolerances *** High shock version available Note: all parameters are measured at ambient temperature with a 10M and 10pF load at 5V
PIN CONNECTIONS
___
1. Output Enable, INH (Tri-State) or NC 2. Ground 3. Output 4. VDD
PACKAGING
CXOM - Tray Pack (Standard) - 16mm tape, 7" or 13" reels (Optional) Per EIA 481 (see data sheet 10109)
HOW TO ORDER CXOM SURFACE MOUNT CRYSTAL OSCILLATORS CXOM "S" if special or custom design. Blank if Std. S 10 T *E = Enable T = Tri-State N = Neither SM3 32 MHz ( 100ppm **Calibration Tolerance @ 250C (A) (B) (C) / 100ppm / 200ppm / I )
10 = 10 TTL Load
Frequency Blank = SM1(std.) SM1 = Gold Plated SM3 = Solder Dipped
Total Frequency Frequency Stability over Tolerance Temp. Range
Temp. Range: C = Commercial I = Industrial M = Military S = Special
* Enable available over 10MHz ** Other calibration fill in ppm
10116 - Rev C
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
Others parts begin by cx
CX-1 CX-2 CX-3 CX-4 CX-5 CX-6 CX-7 CX-8 CX-9 CX-10 CX-11 CX-12 CX-13 CX-14 CX-15 CX-16
|
|
|
