|
Details, datasheet, quote on part number:RBHV7224DG
| |
Datasheet text preview:
HV7224 40-Channel Symmetric Row Driver
Ordering Information
Device 80-Lead Ceramic Gullwing HV7224DG Package Options 64-Lead 3-Sided Die in waffle pack Plastic Gullwing HV7224PG HV7224X 80-Lead Ceramic Gullwing (MIL-STD-883 Processed*) RBHV7224DG
HV7224
* For Hi-Rel process flows, refer to page 5-3 of the Databook.
Features
Processed with HVCMOS® technology Symmetric row drive (reduces latent imaging in ACTFEL displays) Output voltage up to 240V Low-power level shifting Source/Sink current 70mA (min.) Shift Register Speed 3MHz Pin-programmable shift direction (DIR, SHIFT) Hi-Rel processing available
General Description
The HV72 is a low-voltage serial to high-voltage parallel converters with push-pull outputs. It is especially suitable for use as a symmetric row driver in AC thin-film electroluminescent (ACTFEL) displays. When the data reset pin (DRIO) is at logic high, it will reset all the outputs of the internal shift register to zero. At the same time, the output of the shift register will start shifting a logic high from the least significant bit to the most significant bit. The DRIO can be triggered at any time. The DIR and SHIFT pins control the direction of data shift through the device. When DIR is at logic high, DRIOA is the input and DRIOB is the output. When DIR is grounded, DRIOB is the input and the DRIOA is the output. See the Output Sequence Operation Table for output sequence. The POL and OE pins perform the polarity select and output enable function respectively. Data is loaded on the low to high transition of the clock. A logic high will cause the output to swing to VPP if POL is high, or to GND if POL is low. All outputs will be in HighZ state if OE is at logic high. Data output buffers are provided for cascading devices.
Absolute Maximum Ratings
Supply voltage, VDD1 Supply voltage, VPP Logic input levels Continuous total power dissipation 2 Plastic Ceramic Operating temperature range Storage temperature range Lead temperature 1.6mm (1/16 inch) from case for 10 seconds -0.5V to +7V -0.5V to +260V -0.5V to VDD +0.5V 1200mW 1900mW
Plastic -40°C to +85°C Ceramic -55°C to +125°C -65°C to +150°C 260°C
Notes: 1. All voltages are referenced to GND. 2. For operation above 25°C ambient derate linearly to maximum operating temperature at 20mW/°C for plastic and at 19mW/°C for ceramic.
02/96/022
Supertex Inc. does not recommend the use of its products in life support applications and will not knowingly sell its products for use in such applications unless it receives an adequate "products liability indemnification insurance agreement." Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the Supertex website: http://www.supertex.com. For complete liability information on all Supertex products, refer to the most current databook or to the Legal/Disclaimer page on the Supertex website. 1
HV7224
Electrical Characteristics
(over recommended operating conditions of VDD = 5V, VPP = 240V, and TA = 25°C unless noted)
DC Characteristics
Symbol IDD IPP IDDQ VOH VOL IIH IIL ISAT VDD supply current High voltage supply current Quiescent VDD supply current High-level output HVOUT Data out Low-level output HVOUT Data out High-level logic input current Low-level logic input current Saturation current HVOUT P-Ch N-Ch
Note: 1. Only one output can be turned on at a time.
Parameter
Min
Max 10 2.0 4.0 100
Units mA mA mA µA V V
Conditions fCLK = 3MHz Outputs low or High-Z One Output High1 All VIN = GND or VDD IO= -70mA IO= -100µA IO= 70mA IO= 100µA VIH = VDD VIL = 0V
190 4.5 50 0.5 1.0 -1.0 -80 75
V V µA µA mA mA
AC Characteristics
Symbol f CLK tW (H/L) tS U D tH D tS U C t SUE tH C tH E t DHL t DLH
* *
Parameter Clock frequency Pulse width - clock high or low Data set-up time before clock rises Data hold time after clock rises HVOUT delay from clock rises (Hi-Z to H or L) HVOUT delay from Output Enable falls HVOUT delay from clock rises (H or L to Hi-Z) HVOUT delay from Output Enable rises Delay time clock to data output falls Delay time clock to data output rises HVOUT fall time HVOUT rise time POL pulse width Output Enable pulse width Slew rate, VPP or GND
Min
Max 3.0
Units MHz ns ns ns
Conditions
150 50 50 1.0 600 2.0 600 250 250 2.0 2.0 3.0 3.0 45
µs ns µs ns ns ns µs µs µs µs V / µs
CL = 330pF // RL = 10k CL = 330pF // RL = 10k CL = 330pF // RL = 10k CL = 330pF // RL = 10k CL = 15pF CL = 15pF CL = 330pF // RL = 10k CL = 330pF // RL = 10k
tO N F tO N R tP O W tO E W
One active output driving 4.7nF load
* The delay is measured from the trailing edge of the clock but the data is triggered by the rising edge of the clock. There is an internal delay for the data output which is equal to tWH. Therefore the delay is measured from the trailing edge of the clock.
2
HV7224
Recommended Operating Conditions
Symbol VDD VPP VIH VIL fCLK IO TA IOD Logic supply voltage High voltage supply Parameter Min 4.5 0 0.7 VDD 0 Max 5.5 240 VDD 0.2VDD 3 ±70 Plastic Ceramic Allowable pulse current through output diode -40 -55 +85 +125 ±300 Units V V V V MHz mA °C °C mA
High-level input voltage Low-level input voltage Clock frequency High voltage output current Operating free-air temperature
Notes: Output will not switch at V PP = 0V. Power-up sequence should be the following: 1. Connect ground. 2. Apply VDD. 3. Set all inputs (Data, CLK, Enable, etc.) to a known state. 4. Apply VPP. 5. The VPP should not drop below VDD or float during operation. Power-down sequence should be the reverse of the above.
Input and Output Equivalent Circuits
VDD VDD VPP
Input
Data Out
HVOUT
GND (Logic) Logic Inputs
GND (Logic) Logic Data Output
GND (Power) High Voltage Outputs
3
|
|
