|
Details, datasheet, quote on part number:P0721UC
| |
Datasheet text preview:
Multiport SLIC Protector
Multipor t SLIC Protector
1 (T1) 2 (G1) 3 (R1) 6 (T2) 5 (G2) 4 (R2)
This multiport line protector is designed as a single-package solution for protecting multiple twisted pair from overvoltage conditions. Based on a six-pin SOIC package, it is equivalent to four discrete DO-214AA packages. Available in surge current ratings up to 500 A for a 2x10 µs event, the multiport line protector is ideal for densely populated line cards that cannot afford PCB inefficiencies or the use of series power resistors. For specific design criteria, see details in Figure 3.24.
Electrical Parameters
VDRM Volts Part N u m be r * P0641U_ P0721U_ P0901U_ P1101U_ 58 65 75 95 VS Volts VT Volts 77 88 98 130 4 4 4 4 VF Volts 5 5 5 5 IDRM µAmps 5 5 5 5 IS mAmps 800 800 800 800 IT Amps 1 1 1 1 IH mAmps 120 120 120 120 CO pF 70 70 70 70
Pins 1-2, 2-3, 4-5, 5-6
* For individual "UA" and "UC" surge ratings, see table below. General Notes: · All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. · IPP is a repetitive surge rating and is guaranteed for the life of the product. · VDRM is measured at IDRM. · VS and VF are measured at 100 V/µs. · Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. · Off-state capacitance is measured across pins 1-2, 2-3, 4-5, or 5-6 at 1 MHz with a 2 V bias and is a typical value. Capacitance across pins 1-3 or 4-6 is approximately half. "UC" capacitance is approximately 2x the listed value for "UA" product. · Parallel capacitive loads may affect electrical parameters.
Surge Ratings
IPP 2x10 µs Amps 150 500 IPP 8x20 µs Amps 150 400 IPP 10x160 µs Amps 90 200 IPP 10x560 µs Amps 50 120 IPP 10x1000 µs Amps 45 100 ITSM 60 Hz Amps 20 50 di/dt Amps/µs 500 500
Series A C
http ://www.teccor.com +1 972-580-7777
2 - 58
© 2003 Teccor Electronics SIDACtor® Data Book and Design Guide
Multiport SLIC Protector
Thermal Considerations
Package Modified MS-013
6 5 4 1 2 3
Symbol TJ TS RJA
Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient
Value -40 to +150 -65 to +150 60
Unit °C °C °C/W
+II +
IPP Peak Pulse Current %IPP
VF
tr = rise time to peak value td = decay time to half value
IT IS IH IDRM VT
100
Peak Value
VS VDRM -V -V
VT
Wavefor m = tr x td
IDRM VDRM IH IS IT
+V +V
50
Half Value
VS
0 0 tr td t Time (µs)
-I -I
V-I Characteristics tr x td Pulse Wave-form
14
Percent of VS Change %
12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160
IH IH (TC = 25 °C)
10
2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160
25 °C
25 °C
Ratio of
Case Temperature (TC) °C
Junction Temperature (TJ) °C
Normalized VS Change versus Junction Temperature Normalized DC Holding Current versus Case Temperature
© 2003 Teccor Electronics SIDACtor® Data Book and Design Guide
2 - 59
http:// www.teccor.com +1 972-580-7777
Data Sheets
|
|
