|
Details, datasheet, quote on part number:P0724UC
| |
Datasheet text preview:
Multiport SIDACtor Device
Multipor t SIDACtor Device
1 (R1) 2 (G1) 3 (T1) 6 (T2) 5 (G2) 4 (R2)
The multiport line protector is an integrated multichip solution for protecting multiple twisted pair from overvoltage conditions. Based on a six-pin surface mount SOIC package, it is equivalent to four discrete DO-214AA or two TO-220 packages. Available in surge current ratings up to 500 A, the multiport line protector is ideal for densely populated, high-speed line cards that cannot afford PCB inefficiencies or the use of series power resistors. SIDACtor devices are used to enable equipment to meet various regulatory requirements including GR 1089, ITU K.20, K.21, and K.45, IEC 60950, UL 60950, and TIA-968 (formerly known as FCC Part 68).
Electrical Parameters
Part Num b er * P0084U_ P0304U_ P0644U_ P0724U_ P0904U_ P1104U_ P1304U_ P1504U_ P1804U_ P2304U_ P2604U_ P3104U_ P3504U_ VDRM Volts 6 25 58 65 75 90 120 140 170 190 220 275 320 VS Volts 25 40 77 88 98 130 160 180 220 260 300 350 400 VDRM Volts 12 50 116 130 150 180 240 280 340 380 440 550 640 VS Volts 50 80 154 176 196 260 320 360 440 520 600 700 800 VT Volts 4 4 4 4 4 4 4 4 4 4 4 4 4 IDRM µAmps 5 5 5 5 5 5 5 5 5 5 5 5 5 IS mAmps 800 800 800 800 800 800 800 800 800 800 800 800 800 IT Amps 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 IH mAmps 50 50 150 150 150 150 150 150 150 150 150 150 150 CO pF 100 110 50 50 50 40 40 40 30 30 30 30 30
Pins 1-2, 3-2, 4-5, 6-5
Pins 1-3, 4-6
* For individual "UA", "UB", and "UC" surge ratings, see table below. General Notes: · All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range. · IPP is a repetitive surge rating and is guaranteed for the life of the product. · Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. · VDRM is measured at IDRM, and VS is measured at 100 V/µs. · Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for "UA" product. "UB" and "UC" capacitance is approximately 2x higher.
Surge Ratings
IPP 2x10 µs Amps 150 250 500 IPP 8x20 µs Amps 150 250 400 IPP 10x160 µs Amps 90 150 200 IPP 10x560 µs Amps 50 100 150 IPP 10x1000 µs Amps 45 80 100 ITSM 60 Hz Amps 20 30 50 di/dt Amps/µs 500 500 500
Series A B C
http ://www.teccor.com +1 972-580-7777
2 - 22
© 2003 Teccor Electronics SIDACtor® Data Book and Design Guide
Multiport SIDACtor Device
Thermal Considerations
Package Modified MS-013
6 5 4 1 2 3
Symbol TJ TS RJA
Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient
Value -40 to +150 -65 to +150 60
Unit °C °C °C/W
+I +I
IPP Peak Pulse Current %IPP
tr = rise time to peak value td = decay time to half value
IT IT IS S IH IDRM
V --V VT VT VDRM VDRM VS V
S
100
Peak Value
Wavefor m = tr x td
+V +V
50
Half Value
0 0 tr td t Time (µs)
-I -I
V-I Characteristics tr x td Pulse Wave-form
14
Percent of VS Change %
10
IH (TC = 25 °C)
12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160
2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160
IH
25 °C
25 °C
Ratio of
Case Temperature (TC) °C
Junction Temperature (TJ) °C
Normalized VS Change versus Junction Temperature
Normalized DC Holding Current versus Case Temperature
© 2003 Teccor Electronics SIDACtor® Data Book and Design Guide
2 - 23
http:// www.teccor.com +1 972-580-7777
Data Sheets
|
|
